washer bottle pump / filter removal feel free to give me feed back good/bad will be appreciate like and subscribe.
Пікірлер: 28
@billm.2477 Жыл бұрын
Thanks so much for this -just used this vid for my Corsa -and job done! I found I could only push the pump upwards (couldn't pop it right out) but that cleared the space to remove the filter (filled with gunk -exctly like yours) and now all 3 jets are working again. Thanks again for an excellent, clear explanation -great work :)
@properjob7970 Жыл бұрын
You're welcome, glad you found it useful. 🙂👍
@Dmerg4 ай бұрын
You've just saved me an MOT failure next month, surprise surprise the filter was clogged. Cheers!
@properjob79704 ай бұрын
That's what I like to hear! You're welcome
@jasondower64192 ай бұрын
Thank you. Saves me a lot of work as I did the water pump filter and fixed problem as I could see a little water when working and the pump noise. Great video
@properjob79702 ай бұрын
You're welcome, thanks for your comment 😊
@Neri42Ай бұрын
Thank you! You helped me 100% with this Video
@Ericcartman8126 Жыл бұрын
Yes I found this "remotely useful" haha - in fact I found it completely useful, saved me a ton of time diagnosing the fault. Thanks for taking the time to post this
@properjob7970 Жыл бұрын
You're welcome, thanks for your feedback 👍
@gattoflyer11 ай бұрын
Good video. Thanks for taking the time to post this.
@properjob797011 ай бұрын
You're welcome, thanks for your comment.
@nicksullivan16152 ай бұрын
Great video thanks 👍
@properjob79702 ай бұрын
You're welcome, thank you 😊
@smurfiennes Жыл бұрын
Thank you, I’ll clean also the little filter as well
@properjob7970 Жыл бұрын
You're welcome, thanks for your comment. 🙂
@Watkinsss2 жыл бұрын
Good vid, thanks for the help!
@properjob79702 жыл бұрын
You're welcome, and thank you.
@KendalSmithy Жыл бұрын
Nice one. Just what I was looking for so will tackle it forthwith.
@properjob7970 Жыл бұрын
Good, thanks for your comment. Good luck 🙂
@blazecsf5124 Жыл бұрын
excellent thaks
@properjob7970 Жыл бұрын
You're welcome 🙂
@blackhurst98 Жыл бұрын
1st had trouble getting the rusted screw out of the wheel arch lining and the reservoir bottle full of gunk like the bottle had a skin of gunk growing in the walls sadly I broke one of the pipes
@properjob7970 Жыл бұрын
That's the joys of working on car's, you could try putting some washing up liquid in the water tank to break up the gunk. Is the pipe broken at the connector? You could shorten it maybe.
@blackhurst98 Жыл бұрын
@@properjob7970 thanks it was the little u bend that joins the pump I pushed the pipe up to the top of engine so I could get a better look the end cracked so I just used some electrical tape to tighten connection pipe seems to holding
@properjob7970 Жыл бұрын
Ideal, that should work OK. It doesn't really put a lot of pressure on the pipes. Cheers
@seyid_can Жыл бұрын
👍
@davidcurry44853 ай бұрын
Hi there, great video .i have a corsa d 2010 with the same problem. Im having problems with the lining screws. Do they unscrew or are they pop rivets. Whats the best tool to remove them. Thanks
@properjob79703 ай бұрын
Thank you, I believe they are like a pin that makes it expand in the hole to secure the lining. You can push it right through and then remove it, but you may lose the centre pin. Hope this helps, cheers