Cracking into a CMI Home Safe

Рет қаралды 13,787

2 жыл бұрын

Extract from video 762
BACKGROUND: I was playing around with a CMI H2 home safe and accidentally disconnected the LaGard digital lock cable and then I closed it!
Ooops!
So I had to use a drill and bore camera microscope attack to reconnect the cable so I could get in.
Full video: • EEVblog #762 - How Sec...
Australian made CMI H2 Home Safe
12mm hardended steel door with manganese anti-drill plate
6mm hardended steel case
Support the EEVblog on:
Patreon: / eevblog
Odysee: odysee.com/@eevblog:7
EEVblog Web Site: www.eevblog.com
Main Channel: / eevblog
EEVdiscover: / eevdiscover
AliExpress Affiliate: s.click.aliexpress.com/e/c2LRpe8g
Buy anything through that link and Dave gets a commission at no cost to you.
Donate With Bitcoin & Other Crypto Currencies!
www.eevblog.com/crypto-currency/
T-Shirts: teespring.com/stores/eevblog
#Safecracking #Safes #lockpicking

Пікірлер: 71

@petersage5157 2 жыл бұрын

Dave Jones performs laparoscopy on a safe. I think the tool you want for this is a set of arthroscopy or laparoscopy forceps. They're also great for fishing out screws that get lost in the bowels of a chassis. Adam Savage has several pair and says he uses them almost daily.

@BradR86 2 жыл бұрын

"This /is/ the lockpicking EEVBlogger, and what I have for you today is a CMI home safe!" :D

@chrislaplante5040 2 жыл бұрын

A while back I discovered Fish Hook Remover Tools as one of the best ways to grab something really deep in. Long reach and nearly no working room needed like with a pair of needlenose.

@ncot_tech 2 жыл бұрын

“Won’t give up my day job” But Dave, getting overly excited while making a video is your job! 😉

@BenMitro 2 жыл бұрын

The joy comes from overcoming the obstacle...the safe is just a bloody safe. Nice Dave - your success yell was perfect!

@zyzzy1944 2 жыл бұрын

You should have watched the LockPickingLawyer KZfaq channel. He would have shown you how to open it in 30 seconds using just a wet spaghetti noodle. 😉 I enjoy your videos. Thanks, Jack

@EEVblog2 2 жыл бұрын

I knew it would be only a few minutes before a LPL comment. And the answer is no, he wouldn't be able to get into this.

@KeritechElectronics 2 жыл бұрын

"Heeeeey, it's Dave... again.... in my old lab... and what I have for you today is a CMI wall safe I knowthe code for, but still can't unlock it. There's no keyhole on it either, so we'll have to try a different approach." Bloody entertaining, I was laughing all over! Reminds me of MI and Bond movies.

@HomelessTechnology 2 жыл бұрын

Been a while since I watched a video from the garage! Takes me back to when I first started watching EEVblog

@ITTom 2 жыл бұрын

Background music that works best with this video: Mission Impossible

@EEVblog2 2 жыл бұрын

It's in the original video.

@Phred_Phlintstoner 2 жыл бұрын

Nice! I love watching Dave messing with safes!

@russellhltn1396 2 жыл бұрын

And here I was hoping he'd be going all LPL with a EMP attack.

@higihups 2 жыл бұрын

Well, without power to retract the bolts, an EMP will not help much. Also, a quality safe will not have a "default to open" fallback. Though I have a slight deja vu with this video...

@russellhltn1396 2 жыл бұрын

@@higihups If I remember right, LPL showed that with an EMP attack, the electronics tended to reset to factory. Either a default code found in the user manual, or "unlocked" mode.

@higihups 2 жыл бұрын

@@russellhltn1396 Even if it would be vulnerable to an EMP(what a quality safe should not be, LPL says about that: "it usually works on cheap electronics"), it would not have opened. Neither if there would be a magic ritual, to load the factory settings. It was unplugged.

@andreasu.3546 2 жыл бұрын

My OCD wants me to vacuum up those metal shavings on the bench all the time.

@1231trainfan 2 жыл бұрын

Lock Picking Lawyer has nothing to worry about

@NaoPb 2 жыл бұрын

Well done Dave 👏🏻

@AdityaMehendale 2 жыл бұрын

5:50 6:04 So many opportunities for a double-entendre :p giggidy.

@organiccold 2 жыл бұрын

Dave that was a rookie mistake to leave the cable unplugged, but glad you did it as it provided good content for us :)

@landspide 2 жыл бұрын

nostalgia is strong with this one

@bertblankenstein3738 2 жыл бұрын

Very nice recovery. Well done.

@gregalss 2 жыл бұрын

Great Video Only In Australia

@imajeenyus42 2 жыл бұрын

Get a pair of Hartmann crocodile forceps - they are perfect for jobs like this! The have a little grabber at the end of a long neck which can easily pass through small holes.

@strehlow 2 жыл бұрын

I've got a couple jumbo hemostats that are about 30cm total length. One has a curve to it. Very handy!

@paulpkae 2 жыл бұрын

Brilliant! Watch out Hatton Garden...

@davepauljones 2 жыл бұрын

Nice to see the old Dave again, I'll have some of what your on!

@graeme8755 2 жыл бұрын

Dave is not not that Old, he's matured well.

@umbraelegios4130 2 жыл бұрын

Where is the burning twigs tied to a stick(Torch). All I seen was a Flashlight. 😂

@Fanta.... 2 жыл бұрын

We call everything portable that puts light out a torch downunder mate.

@tom23rd 2 жыл бұрын

Haha too good Dave, triumph!

@AlexPlusLEDS 2 жыл бұрын

Haha, didn't this happen once in the past as well? Same fix, drill a hole and clip it in.

@NeverTalkToCops1 Жыл бұрын

Daiyve, Daiyve, Daiyve, I gave you 30 seconds on this one. That was too much.

@5Breaker 2 жыл бұрын

I wouldn't be a bit surprised if the manufacturer had a professional custom tool just for this kind of work.

@gunplaojisan7557 2 жыл бұрын

I have pretty much same lock on the safe that's bolted to the concrete slab inside the concrete cavity and wired to the seismic sensor and then to the alarm system. so if someone somehow bypass the movement sensor and find its hiding spot soon as he/she touched the safe it will trigger the alarm. I've been replacing the 9V battery every 2 years but wonder what happened when its battery is completely run down. will it work with the programed codes once the battery is replaced?

@EEVblog2 2 жыл бұрын

Yes, the code is stored in EEPROM

@EEVblog2 2 жыл бұрын

@@EarthSouthside No, EEPROM are rated for much longer life, decades.

@coryengel 2 жыл бұрын

“Scissor clamp foreceppie things”, aka hemostats

@SirBoden 2 жыл бұрын

Low range works better for large drill bits. More cutting torque and better control.

@rocketman221projects 2 жыл бұрын

Yes, too high of speed will just burn up the drill bit, especially when you don't use oil. A mag drill would make things much easier as well.

@adam3842 2 жыл бұрын

Well done!

@SystemX1983 2 жыл бұрын

Hi Dave, not sure if these things would have been long enough, but did you try the small clamping type multimeter probes? ======< Some call them "Kleps" (Klemmprüfspitzen) here in Germany.

@paulc9139 2 жыл бұрын

Old habits die hard🤦‍♂🤦‍♂🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣

@evensgrey 2 жыл бұрын

Didn't you do exactly the same thing once before?

@metallitech 2 жыл бұрын

Hm, this felt like a time-warp for some reason...

@Okurka. 2 жыл бұрын

Extract from video 762

@WacKEDmaN 2 жыл бұрын

SMH... you wont do that again will ya?! :P LOL nice job tho!... that was sorta too easy! how long did it take ya all up?!

@ratdude747 2 жыл бұрын

And I thought the "ship in a bottle" laparoscopy work I just did this evening on my 1984 Ford F150's gas tank was bad. The "sock" (pre-filter) on the fuel pickup tube had fallen off (was in there replacing a wonky sending unit, which also contains the pickup tube) and I only had the sending unit hole to work with (I still had it under the truck with the filler neck attached. With my wife's help, I finally was able to fish it out with a coiled part grabber thing. I had tried spearing it with a coat hanger but all that did was turn it into the worlds most annoying game of foosball ever.

@cuteswan 2 жыл бұрын

I remember this. :D

@BRADASSOFFGRIDHOMESTEAD 2 жыл бұрын

Larger the diameter drill, the lower the speed should be. Metal has a law you have to abide by. Surface Feet Per Minute. Different steels/metals have different speeds. With your drill, Aluminum you can run it as fast as you want, but most steels you should be on setting 1 and probably only half speed and using something like WD-40 as a coolant/lubricant.

@Okurka. 2 жыл бұрын

*hardended*

@keithmarlow143 2 жыл бұрын

Just waiting for a comment from the lock picking lawyer....

@EEVblog2 2 жыл бұрын

You won't see it because he can't get into it. There is literally nothing to pick. And there is no way to access the locking retraction bolt mechanism.

@johnsonlam 2 жыл бұрын

New skill ~

@wburger2178 2 жыл бұрын

Next time just ping the LPL beforehand! (LockPickingLawyer)

@Zardwark 2 жыл бұрын

Using the pick that Bosnian Bill and I made..

@chris_is_here_oh_no 2 жыл бұрын

Great video, you may need to start another channel at this point.

@entropyachieved750 2 жыл бұрын

Air arc gouge it...

@McTroyd 2 жыл бұрын

So... how long did it take you to drill holes in the safe? 🙄 #AskingForAFriend 😁

@EEVblog 2 жыл бұрын

Like a minute or something, not long. Didn't have a great bit.

@paulcohen1555 2 жыл бұрын

Sure, sell it with this video and it's worth double the price.

@ChongMcBong 2 жыл бұрын

bobby dazzler :)

@jlphtc 2 жыл бұрын

Lol if you had mig welder (cause their easiest to learn basically point & squirt) you could have just cut yourself a nice little square out with the grinder. Then welded the cut-out back in place. A bit of a sanding the weld flat a touch of paint & no one's the wiser. The alternative was your way & I ain't got your patience to do that.

@SeanBZA 2 жыл бұрын

That is how my father got a house safe, it was broken into with the thieves cutting a hole in the side using a hammer and cold chisel (in the days when angle grinders were a specialty tool, and not common), so he used tinmans rivets to put a patch on the inside to fill the hole, and poured into the side cavity plaster of paris to make it fire resistant again, then spot welded a patch on the outside, and painted it. Nice free safe, and it came with a half dozen keys as well. He used it as a document safe, because of the fire resistance, not as a valuables safe.