No video

Computer power supply for car amp

  Рет қаралды 1,373,751

CrazySub777

CrazySub777

Күн бұрын

Adaptation computer power supply for car amplifier

Пікірлер: 485
@210Designs
@210Designs 7 жыл бұрын
Did the same thing for test bench. Great vid!
@Kotastraphy
@Kotastraphy 7 жыл бұрын
Hi Great Video i have actually done this project my self and something i found thats good is if you draw to much current from them they normally shut off automatically before they damage them selves. another power source i used was the LED power kits you can buy off Ebay as they actually have a variable voltage from 10-14.5 volts which is super useful however they dont protect them selves so you have to be careful you dont draw to much current from them havent killed one my self yet but i have had one get pretty warm
@Kotastraphy
@Kotastraphy 7 жыл бұрын
Provo Beast Audio Installation I am not using high power amps but I am using a 23 amp power supply and had no issue in the 2 years of use its had
@Kotastraphy
@Kotastraphy 7 жыл бұрын
should be fine computers dont use full power from power supplys so
@Divinelime
@Divinelime 7 жыл бұрын
thank u bro its working and i can understand easily thumbsup new subscriber
@anupambhowal1554
@anupambhowal1554 7 жыл бұрын
Thanks for video.Nicely explained.
@bsundarsuraj
@bsundarsuraj 7 жыл бұрын
You got the ability to explain like a teacher. Nice Share. Suggest me one CAR woofer with inbuilt amplifier.
@djebliusto9919
@djebliusto9919 4 жыл бұрын
Good work To protect the ATX again short circuit. It will be better to connect the Green wire (power on) to Relay contact with black wire. And to energize the relay with the 12 v or 5 v accorditly.
@benardwambui9083
@benardwambui9083 4 жыл бұрын
Thanks for this a question how do I reduce the screeching sound from the power supply when I switch off
@Lust4Shorts
@Lust4Shorts 5 жыл бұрын
It's soo useful Instead of buying power supply I used atx and got more output for my home theatre 😍🙏
@Speakershocker
@Speakershocker 7 жыл бұрын
Du weist schon das PC Netzteile Schaltnetzteile sind oder? Die sind für die Dauerlast einer Endstufe nicht ausgelegt, folglich dessen reagieren Schutzeinrichtungen auch nicht immer und das Ding falckelt schneller ab als Du geiler Sound sagen kannst. Die Endstufe die du dran hängst wird eh nicht mehr als stabile 20 Watt rausgehen, weil die Spannung von Anfang an schon zu gering ist. Wenn man 50 Euro für ein Netzteil und 50 Euro für eine Endstufe ausgehen hat, plus Kleinteile ist das für 20 Watt rausgeschmissenes Geld. Davon bekommt man ne t.amp e400. Die leistet locker 10 mal mehr als die 20 Watt die bei dem Pfusch rauskommen. Strom ist Lebenslänglich!
@user-lu6fy3md4h
@user-lu6fy3md4h 7 жыл бұрын
great brother but can u tell me what is song name u add in video started plzz
@tomkocur
@tomkocur 6 жыл бұрын
The problem with cheap computer PSUs is that 12V output depends on the load on 5V rail. If there's no load, you will get a very soft 12V rail - voltage will quickly decrease with any load. To get the most out of a PSU like this, you need to put a solid load on the 5V rail. It's a different story with modern PSUs that get 5V and 3,3V output from a 12V rail and will allow you to drain full power from the 12V rail (that's also how you know it's this kind of power supply - max output on a 12V rail will be the same as a total max output).
@antonioprado8068
@antonioprado8068 6 жыл бұрын
Tomas Kuruc I just bought a thermaltake sp-850m for a jl360/2. Amp uses a 50amp fuse. The psu is 70a/840watt on single 12v. Would I still need a dummy load on the 5v and 3.3. I purposely got a bigger psu that is also an 80plus bronze to help with heat and efficiency as I need this amp to run at least at 80% load,bridged which will be between 280-360 watts. And this needs to run for a minimum of 5hrs at this load. So I know the basics which is adding all yellow, black and putting green/black. Now what I need help with is efficiency, and stable load. So if that requires dummy resisters etc and where, please shed light or find me a video of someone doing exactly this cause all these video sick cause they never show the system working or if they do, at what volume to let me know it's stable
@tomkocur
@tomkocur 6 жыл бұрын
that all depends, check the actual voltage on 12V rail while the amp is in load, if it doesn't fall below 11,5V, you're all good, if it does, just connect a couple of car bulbs (in parallel) to the 5V rail (red). That PSU has a strong 12V rail and is quite modern, so it might not even have the type of regulation that's used on cheap PSUs.
@sajiprasad
@sajiprasad 3 жыл бұрын
Please simplify didnt understand..what is 5 v rail
@brandonjohnson7851
@brandonjohnson7851 3 жыл бұрын
Very easy I use to do this when I was 15 I’m 33 now
@sinuromeo3905
@sinuromeo3905 4 жыл бұрын
Thnz brother i have successfully connected to amp
@ernestosantizo7974
@ernestosantizo7974 7 жыл бұрын
Man thanks for this. You really saved me here. Appreciate it.
@steveespinoza200
@steveespinoza200 3 жыл бұрын
11.97 is a little low. Should be more like 13.5 to 14.0 to get thr best power
@sterlingbartlowe3056
@sterlingbartlowe3056 4 жыл бұрын
watts = amps x volts. The chart on the side of the power supply, the one the video shows, has the watts listed for each of the rails, and a maximum overall wattage. Divide that wattage by 12 and you got your amps. Use the proper sized wire for that amperage if you use a junction block, and I wouldn't use a cheap or exceptionally long power cable or extension cord.
@rmblwgn
@rmblwgn 4 жыл бұрын
12v amps are always listed on the sticker on back.usually No need for estimating
@niknovsak3288
@niknovsak3288 2 жыл бұрын
So I get a 650w power supply for a 600w mono amp and connect all ground wires together and all 12v wires together and make a psu on switch and hook up my amp?
@kennymelusi8067
@kennymelusi8067 7 жыл бұрын
ya it work, I tried it and it worked thanks
@jenelskiemajiks9934
@jenelskiemajiks9934 4 жыл бұрын
i did this and after a week for 3 hours a day of playing disco music, the power supply blown up. it wont last because it is not designed for heavy surge during rapid bass kicking. i used 750 watts PSU for 300watt car amp but it toasted some rectifier and resistors.
@expressfax5420
@expressfax5420 4 жыл бұрын
WHAAAAT 750W PSU IS BOOOOM GONE?
@expressfax5420
@expressfax5420 4 жыл бұрын
Was it bronze 80+ quality psu
@Anjalinayyar132
@Anjalinayyar132 4 жыл бұрын
this is real review
@dntlss
@dntlss 4 жыл бұрын
Let me ask you something,lets say you had a amp and a car stereo and a speaker and you just wanted to check and see if everything works,could you hook it up to a car battery for lets say a couple of minutes? not permanent,just to see if everything is OK? thank you for your time.
@dominodd3879
@dominodd3879 3 жыл бұрын
@@dntlss you would have to make a simple 12v switch for the amplifier. I dont know about the stereo but i know u can connect an amplifier to a car battery. Exocontralto does it all the time
@adrianmilanesi9143
@adrianmilanesi9143 Жыл бұрын
Hi Great video, if i join +12V1 and +12V2 will i get 30 amps output? Thanks
@vinothkumarnagarajan2968
@vinothkumarnagarajan2968 6 жыл бұрын
Awesome video mate thanks lot for clarify my doubt great video good efforts ......thanks mate
@mdshoeab808
@mdshoeab808 5 жыл бұрын
This video is so helpful ,thanks a lot.
@crownedmedia7936
@crownedmedia7936 4 жыл бұрын
I figured out if you get a cheap crappy bluetooth speaker gut it then wire the insides to a car sub it works fine.. it works with any speaker, I've tried all 20 of mine
@1oneguythat
@1oneguythat 4 жыл бұрын
Rip bt speakers lol
@1oneguythat
@1oneguythat 4 жыл бұрын
Ive thought about doing this, the power wire got a short on one of my bt board gonna hard wire it and do just that
@onca6742
@onca6742 4 жыл бұрын
I did the same thing It was a jbl extreme 2, I took the tweeters and hooked it up to 2 12 inch kickers with the 2 tweeters on the bottom of the box
@ProjectHazy
@ProjectHazy 4 жыл бұрын
Best video yet!
@electronicshelpcare
@electronicshelpcare 5 жыл бұрын
Great video.
@jingoit6545
@jingoit6545 3 жыл бұрын
Is there a downside to using the switch on the back of the psu instead?
@raymondkhan2709
@raymondkhan2709 4 жыл бұрын
Great video. Thumbs up. How and what wire should I use for low voltage led strips
@DJRS9045
@DJRS9045 4 жыл бұрын
I have one power supply, a pioneer head unit and one car amp that I need to power. Will one power supply power both at the same time?
@alexanderoronov4392
@alexanderoronov4392 6 жыл бұрын
Neat work, bro. Love it.
@deedogg83
@deedogg83 7 жыл бұрын
can you use 2 power supplies together wire in parallel if the amps are different. if so will it boost the amps up
@j-walking7080
@j-walking7080 7 жыл бұрын
I'm here looking for that same answer also :'(
@deedogg83
@deedogg83 7 жыл бұрын
Justin Chan no u can't it will not do anything to the amps
@j-walking7080
@j-walking7080 7 жыл бұрын
dwayne Wilcott so what u mean is if i use two amps it won't work or??
@deedogg83
@deedogg83 7 жыл бұрын
wiring 2 power supplies with different amps won't give u a higher amp count. your best bet is to find a power supply that has the right power and amps u need. I use 2 power supplies to do my boombox one to run my CD player and lights and another power supply just for my sub
@j-walking7080
@j-walking7080 7 жыл бұрын
dwayne Wilcott oh im currently running my car stereo on a gamecube power supply and it works fine. But i guess I'll just use one computer psu for my amp that I'm gonna buy soon.
@shivamchaudhary5042
@shivamchaudhary5042 6 жыл бұрын
Thanks bhai abb mera apm ghr pr bhi chal rha hai thanks guru............🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏😘😘😘😘😘😘😘😘😘😘😘😘😘😘😘😘😘😘😘😘
@Davindersingh-oy9zx
@Davindersingh-oy9zx 6 жыл бұрын
bhai kitne watt ka amp chla rhe ho .
@Davindersingh-oy9zx
@Davindersingh-oy9zx 6 жыл бұрын
ok bro
@Davindersingh-oy9zx
@Davindersingh-oy9zx 6 жыл бұрын
sony 1000 watt 4 channel. model number = xmn10044
@Davindersingh-oy9zx
@Davindersingh-oy9zx 6 жыл бұрын
kitne paise lg jayenge bhai g
@Davindersingh-oy9zx
@Davindersingh-oy9zx 6 жыл бұрын
sony 1800 watt 420 rms
@davidrollison6756
@davidrollison6756 6 жыл бұрын
and you can run these supplys together to get as much volts as you need. if you hook the blue off of #1 supply and the yellow off #2 supply together then come off of the blue and yellow thats left not used you will get 48 volts. hook 3 supplys together get even more
@videomaker811
@videomaker811 6 жыл бұрын
No u wrong. Please learn electronic. The voltage is still the same just increase the current. But u can't combine all of them cause it have different current output. If u device draw more current then the one with lower current output will burn the ic inside the psu.
@TechnikToni-Overtribe
@TechnikToni-Overtribe 7 жыл бұрын
you have to load down the 5v rail to stabilize the 12v rail
@trei2unu
@trei2unu 7 жыл бұрын
what resistor value is recommended for that?
@manuelpereiradasilva9930
@manuelpereiradasilva9930 7 жыл бұрын
DerTechnikKanal Google Tradutor
@Pirmy76
@Pirmy76 7 жыл бұрын
Never used a dummy load for this. The 12V was always stable. I used this power supply in my workshop for years... and never had problems.
@_24___
@_24___ 4 жыл бұрын
@@trei2unu 1 ohm 20w
@raymondkhan2709
@raymondkhan2709 2 жыл бұрын
Great video. How do I add a voltage meter . Or annotate meter, whatever I should be looking at before I fry something
@bobbavet
@bobbavet 6 жыл бұрын
Thanks for the vid. Do you have to use all the black wires or can you just use the same amount as the yellow wires? Do you think you could power 2 x 200W car amps with a single 500W PSU? I would like to put 2 in for shaker driver in a car sim seat. 1 for left channel and 1 for right channel.
@mc__mauri8863
@mc__mauri8863 6 жыл бұрын
in theory its possible, but it can burn your wires so its not safe
@_24___
@_24___ 4 жыл бұрын
Use 4 black wire and 4 yellow wire
@mohamedfaizalyacoob8731
@mohamedfaizalyacoob8731 5 жыл бұрын
I have 2400w hoofer that need how much amp ? Or Enough for this watts ?
@bacardilove1981
@bacardilove1981 5 жыл бұрын
Ok with the voltage but when yhe amp needs amperes what you will going yo do??? I have put it with me US Amps 1600w 4 channel inly a 10inch woofer and the speakers play from cd player but after turn on the volume starts blinking like a Christmas tree..
@vpLuBu
@vpLuBu 5 жыл бұрын
You need a bigger psu, they make some that go up to 1500 watts. You would have to run 2
@omkargavali6197
@omkargavali6197 6 жыл бұрын
Hello Brother I always watch your videos I am also interested to make a car audio system inside my house but actually I am a Mechanical Engineer So can please tell me how to get with amplifer and power Supply because I have JBL 1100 Watt amplifer
@juliojayayala5592
@juliojayayala5592 7 жыл бұрын
just like you said , the 12v converter doesn't give much power to my amplifier and as soon as I turn up the volume the stereo shuts off , so I was gonna go with a 26 amp battery but then I saw your video and looks like a better solution , my amifier is a 4 channel 900 watt max , can you send me a link of a good cpu power supply that will give good power , wud reall appreciate it , thanks
@maltepettersson3083
@maltepettersson3083 7 жыл бұрын
Jay Ayala go with both battery and psu
@AntonioFerreira-pg1fh
@AntonioFerreira-pg1fh 5 жыл бұрын
Parabéns amigo ótimo vídeo.
@meenatchisundaram2462
@meenatchisundaram2462 7 жыл бұрын
Great..!
@meenatchisundaram2462
@meenatchisundaram2462 7 жыл бұрын
Generally .. SUV batteries are 80-90 Ah - 12V . 12 x 80 = 960 watts.There is no problem . If we connect it in to a heavy truck battery (150 Ah ) 150Ah x 12v =1800w there is also no problem with the car audio we know ! In my point of view computer power supply output which we are using is a pure DC as like from battery source. So no need to panic..!
@Pirmy76
@Pirmy76 7 жыл бұрын
I think you should learn the difference between A and Ah. Saying that a 80 Ah battery is 960W is... well totall nonsense. The 80Ah battery specification meand that the battery has 80Ah capacity. It means that a battery can supply 80A for one hour. Example: if you have a device that uses 10A 12V (120W), the battery will be dead in 8 hours. If you have a device that uses 40A 12V (480W) then the battery will be dead in 2 hours. Calculating Ah x V is.. nonsense.
@shahtajahmed4887
@shahtajahmed4887 6 жыл бұрын
4ch amp ko minimum 25ampare Chaya or 2ch main agr skr hai 10ampare chalay GA ya 1woofer par 15ampare chalay GA ya main nay try Kia hai
@itmightbeken8371
@itmightbeken8371 7 жыл бұрын
Think i might try this
@simbatale
@simbatale 6 жыл бұрын
Hi mate! Thx the video! The thing is I did everything the same as you but when I start it the fan is rolling a short time and turning off. I read many forum sites but no one can give a normal answer. The power supply is brand new. What do you think?
@josephsvensson6637
@josephsvensson6637 6 жыл бұрын
Some atx power supplies will shut off after a while if no load is detected. Try putting a 1A load on the 5V rail. A 5 ohm power resistor should do the trick, just make sure its rated for at least 5W
@simbatale
@simbatale 6 жыл бұрын
I ordered an older type of power supply and it is working but I have two power supply now lol anyway I will try the resistor trick. I hope it will be working. Thank you for your advice. :)
@Jawad.1
@Jawad.1 5 жыл бұрын
The problem (at your side) is with the positive and negative connection with the amp! You have connected positive 12v wire of PSU with negative 12v wire of the amp. Connect positive with positive and negative with negative and your problem will be solved. PSU turns itself off when it senses the improper connection. It's a safety measure built into it.
@felixlegendre2145
@felixlegendre2145 5 жыл бұрын
the problem is that the psu have an over current/over voltage protection that cut the power when it exceed the current limit imposed by the psu. it is possible to bypass those protection by buying some circuit board sold on internet for about 5-25$
@shivnoorsinghbajwa6503
@shivnoorsinghbajwa6503 4 жыл бұрын
How much ampher we get after joining all wires 🤔 plz reply I want to use car amp.. at home
@_24___
@_24___ 4 жыл бұрын
0:09 you can read that
@davidrollison6756
@davidrollison6756 6 жыл бұрын
shefin you would have to get a smaller amp hour battery like a 12v 1ah i think. stay with 12v but get smaller batterys and test witch one puts out 1amp. or get a amp step down off ebay
@jayhonda8759
@jayhonda8759 3 жыл бұрын
do you have to use all the wires in order to make this work or can you just use one coming off one of the runs?
@bosskage8474
@bosskage8474 3 жыл бұрын
U could use onley one
@amandlaawethu1538
@amandlaawethu1538 Жыл бұрын
I hooked mine up & it sounds distorted. I connected black & yello
@jesusmusicson
@jesusmusicson 7 жыл бұрын
Where did you get the connector you put to the Source ????? please help me
@aurimuxlt1
@aurimuxlt1 5 жыл бұрын
4:24 what kind of transition block is that? how is it called?
@Josh-km9vc
@Josh-km9vc 4 жыл бұрын
I connected my Green wire to a ground to test the PSU and the fan comes on for just a couple seconds then shuts off. What's the deal?
@-AnEv942
@-AnEv942 3 жыл бұрын
some require to see a load on the 5v rail to stay on...light bulb 10 watt resistor etc. Some have 'sense' wires monitoring voltage connected at 21 pin connector. If you see different colored wires going to same pin these should remain connected together. ie mine had a brown wire connected to orange 3v pin and a pink wire to red 5v pin.
@erickfierro4930
@erickfierro4930 6 жыл бұрын
No mantiene un amplificador sonando ya que el voltaje de la fuenta baja demasiado y se apaga el ampli... Yo lo hize y no me sirvió
@johnwohlheter601
@johnwohlheter601 5 жыл бұрын
I would like to power a MTX 8000 12" sub with my old cooler master 500watt power supply. The sub is 400 rms. I was thinking of getting a 300 watt car amp. Would a class A/B or class D amp make best use of a 500watt PSU?
@maltepettersson3083
@maltepettersson3083 5 жыл бұрын
I don't think it's gonna handle 300w very good. Use 200w amplifiers to be safe or get a 12v battery instead, better and safer
@team72filo
@team72filo 4 жыл бұрын
Could yòu please tell me which kind of switcher do i need to connect the green and the black cable forma the on/off?
@chrisram9424
@chrisram9424 7 жыл бұрын
Do u have to use a 3 amp to push the car amplifier
@angelobrown7757
@angelobrown7757 3 жыл бұрын
Which wires is 12volt?and which isgnd?
@TragicalGamerRobloxMore
@TragicalGamerRobloxMore 2 жыл бұрын
yellow is usually 12 volt and black is usually gnd
@krishnendudasgupta3707
@krishnendudasgupta3707 5 жыл бұрын
Is it capable to give 18 amp at 12 V Continiously ? Means rated current at 12 V continiously or it trip if I continuously draw the rated current from it ?
@unvme786
@unvme786 4 жыл бұрын
Hi. I am planning to buy an amp JL audio xd1000/1 to power 2 x 600w subwoofers what do you recommend for this to test working
@anmoldeep9841
@anmoldeep9841 7 жыл бұрын
i have got an 300w amplifier having 25a fuse. So can I use 500w psu which gives 12v dc and 24a.
@_24___
@_24___ 4 жыл бұрын
Yes
@theminimalist9882
@theminimalist9882 6 жыл бұрын
I followed all the mentioned procedures correctly and when i switched on the smps it will automatically turned off.. The amplifier light is blinked once and turn off.. Please give me a solution. Hope your reply soon...
@mrcoolguy0591
@mrcoolguy0591 6 жыл бұрын
ANSHU J same here
@Jawad.1
@Jawad.1 5 жыл бұрын
Possible Solution for the problem that you're encountering is: The problem (at your side) is with the positive and negative connection with the amp! You have connected positive 12v wire of PSU with negative 12v wire of the amp. Connect positive with positive and negative with negative and your problem will be solved. PSU turns itself off when it senses the improper connection. It's a safety measure built into it.
@EweToobUsername
@EweToobUsername 7 жыл бұрын
A real PSU modder would have taken apart the psu so the +5 was available for LEDs and the +12 was coming straight off the PSU's breadboard.
@Ottonic6
@Ottonic6 6 жыл бұрын
Oh, that's what a "real" PSU modder does. Gee, glad I know that... Now I can sleep at night...
@davidrollison6756
@davidrollison6756 6 жыл бұрын
blue as ground will double the volts! so if yellow+ground= 12v blue+yellow=24v
@thejourniganadventures7391
@thejourniganadventures7391 7 жыл бұрын
Will this set up run a head unit and an amp for a subwoofer.
@Pin90able
@Pin90able 7 жыл бұрын
o dont think so try running them in separate power sources
@namegoeshere69
@namegoeshere69 6 жыл бұрын
Yes it will work,but your taking a bit of power away from the amp,you would also want to fuse them separately that way. Use the PSU to power the amp and use a 12v wall adapter to power the head unit
@ankitmeena_ind
@ankitmeena_ind 5 жыл бұрын
are bhiya is SMPS se bass tube power on to ho gyi lekin AMP kam pad rahe he, ye SMPS 12 v 14 amp ka he or bass tube ko 30 amp chahiye, meri bass tube baj to rahi he par low amp hone ki wajaha se bhrrrr bhrrrr kar rahi he
@RajKumar-qm7sb
@RajKumar-qm7sb 5 жыл бұрын
Bhai amplifier ko chalane ke liye kitne amp ki jarurat hai smps le ya transform
@pritamamrutkar8809
@pritamamrutkar8809 5 жыл бұрын
how much ampere needed to run car amplifier can we run on seperate transformer 12v 25 ampere or it runs on smps and which one is best for sound output smps or transformer
@pritamamrutkar8809
@pritamamrutkar8809 4 жыл бұрын
@All in One can we run 10inch bass on smps
@aleqsbitadzeee3389
@aleqsbitadzeee3389 6 жыл бұрын
End whear is amps? 😁 12v? 😁 What u cen to do this 12v?
@dorotejtaseski
@dorotejtaseski 7 жыл бұрын
my amplifier is 75 ampers so computer power supply vould be good or not??? l think computer power supply is good for 25amper amp...l need answers pls hellp :D
@maltepettersson3083
@maltepettersson3083 7 жыл бұрын
lyrics dj well I think I'm going to use a car battery that's hookt up to a PSU and from battery to amp. Because some amplifiers draw just to much amps for a PSU at a few seconds (when the bass drops) and that's when it's good to have a battery also connected to the amplifier. and when I'm not playing and have everything turnt off then you should of course not charge the battery with a PSU cuz it WILL overcharge the battery. So buy a 12v battery charger that's ONLY connected when the hole system is off, so the battery is ready at 12v when you want to play, and have the PSU on while playing music so you don't have to turn down and charge after a while of playing. hoped this helped you.
@ramsingh-en8cb
@ramsingh-en8cb 6 жыл бұрын
agr hm sound jada krte h to 5 amp. km pd jata h is liye ye kamyab nai h
@polcat79
@polcat79 7 жыл бұрын
clever git. great way to recycle.
@garyr7027
@garyr7027 6 жыл бұрын
Now how you gonna supply power to the PSU in a vehicle? There is a way, but not worth what it takes to get it done.
@doja_dre
@doja_dre 6 жыл бұрын
It's meant for in home powering of an amplifier, not going in the car.
@garyr7027
@garyr7027 6 жыл бұрын
Andre Verska ahhh... got it.
@Sfto727
@Sfto727 4 жыл бұрын
I am currently using trying to build one did all wires same as u my watts on power supply is 350 max an I have a 2500 watt amp pushing a 15inch subwoofer. But if I run volume up to 25 its stays running anything after that it dies??? Help
@karlmagnuson737
@karlmagnuson737 4 жыл бұрын
Your power supply should have at least 150w of headroom more than your amplifier. Your subwoofer works at low volume because you aren't asking much from the power supply, but once you give it a higher load the thing craps out because it is no where near powerful enough to support your amplifier.
@jamesgoodacre2305
@jamesgoodacre2305 4 жыл бұрын
Hi, your amp in the real world won't be putting out 2500 watt. You need to know the rms wattage.that usually will be quite a bit lower. Also you need to make sure that any psu you use has adequate amp rating which is the same or better still slightly higher than your amplifier. Check this by simply checking fuses on you amplifier. I would have thought a psu of say 750w minimum with a amp rating of say 60amp would be plenty powerful enough.
@MommyThessKitchen
@MommyThessKitchen 3 жыл бұрын
Naku wala ako alam dito,akap ko na rin Bahay mo na wala kawala
@kuronekosan2830
@kuronekosan2830 Жыл бұрын
Mine is turning red meaning going to protection mode even with no rcas and speaker wires connected ..it's been working fine for 1 year..i didn't use them for 2 months and now it's hsving this issue
@mijan7522
@mijan7522 Жыл бұрын
Can car amp and car stereo run on 1 psu? I just try but amp don't run but player ok. Why?
@aver1234a_ttv
@aver1234a_ttv Жыл бұрын
Too low amperage I presume or you didn't run power to the remote on
@aryanman2
@aryanman2 6 жыл бұрын
Is it pantomime?!
@megahilmi6773
@megahilmi6773 5 жыл бұрын
Good job
@TechTricks786
@TechTricks786 4 жыл бұрын
Amazing
@davidrollison6756
@davidrollison6756 6 жыл бұрын
figured id throw that out there in case anyone did not know
@ironservice4416
@ironservice4416 7 жыл бұрын
Not necessary wires could be to unsolder, and not cut off
@oranbazak3056
@oranbazak3056 7 жыл бұрын
Is it matter with PSU i use for 2000w AMP?
@stateofemergency4966
@stateofemergency4966 6 жыл бұрын
Will this work with any amp??
@electronicstuff4958
@electronicstuff4958 5 жыл бұрын
Nope...actually you cant drive any power amp. With that
@Jordanred23
@Jordanred23 4 жыл бұрын
Could you please tell me which kind of switch i need to connect the green and the black cable to power on and off the PC adapter?(a link maybe)
@bosskage8474
@bosskage8474 3 жыл бұрын
12v switch
@Ls.nando05
@Ls.nando05 3 жыл бұрын
any type of off and on switch you could find some in auto zone for abt $3+ or at walmart
@luckyanna9594
@luckyanna9594 4 жыл бұрын
Koi bhi black or yellow wire le skte he??
@circuit.breaker
@circuit.breaker 4 жыл бұрын
Yes
@esescomputer2709
@esescomputer2709 5 жыл бұрын
its necessary to use car audio cap bank?
@ryanzehner7351
@ryanzehner7351 5 жыл бұрын
I'm Using 2 clarion 5 Channel pro audio Amps 3 alpine 750watt mono amps 1 alpine .2 channel amp and dti 2500 mono amplifier a kenwood touch screen in dash and speakers I'm Running 3 mtx 10s 1ohm Running 2 .alpine 10in single voice coil at 4ohm two 3 ohm 8 in And kenwood 6x9 and a Finally aoldschool hx2 12in at 2ohm sounds amazing competition status
@bacardilove1981
@bacardilove1981 5 жыл бұрын
All that amps and sub only with one PSU??????? How many amp the psu gives you and all that play normal????
@jonasmontana7648
@jonasmontana7648 5 жыл бұрын
I use 12 volts but i also need 5volts how many ground i need in 5 volts thank youu
@kaisermilenium
@kaisermilenium 4 жыл бұрын
trate de cambiarle una bobina que esta recalentada de una fuente de poder de pc de las que estan en el secundario aun asi la fuente enciende pero se apaga al rato, le coloque una identica de otra fuente, marca el mismo valor de la otra pero no enciende le vuelvo a colocar la recalentada y si enciende, fuente cual es ese misterio?
@hardikspd
@hardikspd 6 жыл бұрын
Can u pls tell i can run my sony xpold amp 600 watt with smps power supply 12 wat 24 mpr
@ct.opgaming5440
@ct.opgaming5440 3 жыл бұрын
Thanks broo❤️❤️
@boschbouchenak5445
@boschbouchenak5445 6 жыл бұрын
good job bro
@cheri758
@cheri758 5 жыл бұрын
For my car audio amp i'm using 2 1000w bitcoin miner psu wich has only 12v line and peak 1300w.
@scobby5501
@scobby5501 7 жыл бұрын
can u connect this to another ?
@aakashchoudhary6719
@aakashchoudhary6719 5 жыл бұрын
Bro kya ye car amplifier ka 12v 25amp ka load utha lega? Pls reply
@fahadahmed480
@fahadahmed480 5 жыл бұрын
Check the amps ratings on your power supply
@aakashchoudhary6719
@aakashchoudhary6719 5 жыл бұрын
@@fahadahmed480 ok thanks
@aakashchoudhary6719
@aakashchoudhary6719 5 жыл бұрын
Bro smps ka bijli ki lead kitne rs me aa jayegi?
@HaikalHajja
@HaikalHajja 7 жыл бұрын
it create inverter from ac to dc, but car electricity is dc from the beginning right, it cant be placed directly on a car without the car having dc to ac inverter first.. right ?
@namegoeshere69
@namegoeshere69 6 жыл бұрын
Its pointless to do it that way really,this is just to power the amp on inside your home
@tdmjason
@tdmjason 5 жыл бұрын
mine only puts out 11.4 volts but that will still run 12 volt items - you dont need exactly 12 volts to run 12 volt items - to charge a 12 volt battery to full capacity you need to charge over 12 volts - most cars charge at a max of 14 to 15 volts - anythinig over that things start to fry - ive seen over 18 volts being thrown out of an alternator - thats bad .... charging at a capacity of 10 amps is good - 2 amp to 5 are most trickle wall chargers for batteries.
@alexisgomes6621
@alexisgomes6621 7 жыл бұрын
nice !!
@hamzasat
@hamzasat 4 жыл бұрын
Please help me. is it dangerous to use a power supply that give less power than what the amplifier draw ? I have a crappy pc atx rated as 12.4 = 7.5 Am ( 220 Watts total ) . but my car amplifier is probably 250-500 watts and 40-50 Am
@baileyrosmarin1077
@baileyrosmarin1077 4 жыл бұрын
mehdi Moro there is a key difference between power ratings in car audio and computer components. In computer applications, the psu you own will put out 220w, maybe 250w MAX to give some headroom in the event of power spike. In audio applications power is measured in rms or root mean squared. You should look up the difference between measuring at peak and rms, but if you tried driving your amp with that psu you would blow it up before you get to half volume.
@stevengoelzer
@stevengoelzer 4 жыл бұрын
A good rule to follow when re-using a pc power supply, Look at the AMPS Fuses. You need at least this much amperage on the Power Supply 12V rail(s). For example : If you AMP has 2 x 20A fuses you should at least have 40A of power on the 12V rails. If you had say 42A on your Power supply, It would work but I would not run it hard for very long as the power supply will not last very long pulling max. amps. It would be better to have 50% or more amps to spare. I think doing this will end in tears in days to months as best. Better to just buy a fosi audio BL10C AMP for $45.
@hamzasat
@hamzasat 4 жыл бұрын
@@baileyrosmarin1077 Thank you for your help. I have abandoned that project. Too much risk and the results may not be what im expecting
@hamzasat
@hamzasat 4 жыл бұрын
@@stevengoelzer Thank you for the advice I really don't know shit about electricity and i stayed away my whole life from it . Not gonna start fuckin around now lol as you said. . it's better for me to buy a factory made speakers or boombox... 😊
@goldenstreeetfinance
@goldenstreeetfinance 7 жыл бұрын
Can i connect to Head Unit?
@zeljkoholik5594
@zeljkoholik5594 4 жыл бұрын
thanks works fine
@joey537
@joey537 6 жыл бұрын
Are the wire diagrams the same on all computer power supply??
@mc__mauri8863
@mc__mauri8863 6 жыл бұрын
yes :) it would be disaster if you put 12 volt on 5 volt device
Connect Car Amplifier or Subwoofer at Home
5:15
Techscrew
Рет қаралды 15 М.
PEDRO PEDRO INSIDEOUT
00:10
MOOMOO STUDIO [무무 스튜디오]
Рет қаралды 18 МЛН
Пройди игру и получи 5 чупа-чупсов (2024)
00:49
Екатерина Ковалева
Рет қаралды 4,3 МЛН
Car Audio Amp Computer Power Supply Transformation
28:14
Dominic Gichane
Рет қаралды 23 М.
Powering Car Amps in YOUR HOUSE!
10:27
SparkedEd
Рет қаралды 224 М.
DIY Powerful Ultra Bass Amplifier ATX Computer , Simple Circuit , No IC
13:02
DIY - How to Make a Home Stereo from a  Car Stereo
10:52
Toids DIY Audio
Рет қаралды 1,5 МЛН
how to make 5.1 amplifier class d amplifier 300watts
15:45
ksk makes
Рет қаралды 549 М.
how to wire a computer power supply to a car amplifier tutorial
7:03
Lucid Gaming115
Рет қаралды 43 М.
$10 DC Power Supply - 1 Day DIY
12:14
The Recreational Engineer
Рет қаралды 688 М.