Creality K1 and K1 Max - Using Creality Print as Slicer

Рет қаралды 26,290

11 ай бұрын

Why limit yourself when using Creality Cloud on your new Creality K1 or K1 Max? Check out Creality Print for slicing your awesome 3D models from Printables, Thangs, or other 3D model-sharing sites. With Creality Print you can Slice, send and manage your 3D printer. Enjoy the fun with 3d printing using Creality Print.
Join this channel to get access to the perks:
/ @zachary3dprints
Subscribing is free it doesn't cost anything Just 1 click and like this video, it will help KZfaq bots take over the world!
You can support me on Patreon:
/ zachary3dprints
Social Media:
Facebook: / zachary-3d-prints-1051...
Twitter: / 3dzachary
Instagram: / zachary3dprints
Streambeats from Harris Heller:
STREAMBEATS Copyright Free Music for Streamers (and KZfaqrs!)
Lo-Fi ►► www.streambeats.com/spotify/l...
Synthwave ►► www.streambeats.com/spotify/s...
EDM ►► www.streambeats.com/spotify/edm
Hip Hop ►► www.streambeats.com/spotify/h...
Rock ►► streambeats.com/spotify/origi...
On any other music service just search for Harris Heller
Happy 3D printing, Zachary 3D Prints
#Zachary3Dprints
#Z3DP
#letsmakesomefunwith3dprinting

Пікірлер: 48

@missilpeludo8813 4 ай бұрын

Thanks Zach…. You’re amazing your tips helps me a lot!!!!

@Zachary3DPrints 2 ай бұрын

Hey, sorry for the late reaction. Thank you very much

@vinylsteve Ай бұрын

Thank you :-)

@jerryw5225 10 ай бұрын

Dark Ages here, are you saying I will not need a program (in between my modeling software and the slicing software) to check the integrity of models I make before entering into the Creality Slicer? Thanks

@Zachary3DPrints 9 ай бұрын

Hello Dark Ages, like mentioned, I like to use Printables or other sites to download my models and slice them with Creality Print. You can use Creality Print to look up a model and then slice it or send it directly to your printer if the slicer settings are in the model settings

@bahadir716 8 ай бұрын

Thank you bruh. I wanna ask where the settings are like temparatures and speed.

@Zachary3DPrints 7 ай бұрын

There are more videos about Creality Print going to come. Did you saw my last video after this one, about Creality Print?

@jaym6126 9 ай бұрын

How did you change the view angle thing on the right side to show mlitple angles i only have top and front its not a squar

@Zachary3DPrints 8 ай бұрын

Did I changed the view? Hmmm 🤔 holding the mouse buttons and moving the mouse you can pan and tilt the build plate

@jindranereknu5753 10 ай бұрын

Tell me how to stop printing for a change of filaments in this App?

@Zachary3DPrints 9 ай бұрын

Sorry for the late reply on your comment. Did you find the change option yet? As I have checked, it doesn't seems to have this option. If I find a solution I'll be sharing this

@gabrielaugusto3675 3 ай бұрын

How can i use the k1 in prusa slicer?

@Zachary3DPrints 2 ай бұрын

Sorry for the late reply, I do have a video for that, did you found it? kzfaq.info/get/bejne/Zs2RqLWey9qtdX0.htmlsi=zh_PFvfAzWo5f8-m

@aaronosb7787 6 ай бұрын

How do u change the infill and the number of walls

@Zachary3DPrints 6 ай бұрын

Hey there, I do have a newer video about that, where I show it. kzfaq.info/get/bejne/o7iCecl-x73SdJ8.htmlsi=LQhJpcxk-SU42F5A

@aaronosb7787 6 ай бұрын

Thanks I watched it i just got a k1 max

@malicovasa4571 Ай бұрын

can you add creality printer to bambu studio?

@malditomeobligas4345 Ай бұрын

yes o do it. i am from mexico

@blacknine 10 ай бұрын

Where is support blocker?

@Zachary3DPrints 9 ай бұрын

It doesn't seems to have one, but I might have overlooked it

@jekkedulle 4 ай бұрын

Kan ik Creality Print ook in het Nederlands omzetten?

@Zachary3DPrints 2 ай бұрын

Hmmm, Ik heb er ook eventjes naar gekeken, maar niet gevonden

@aaronloveday4858 10 ай бұрын

Do you know how to change the infill on this software?

@Tenaciouss_B 9 ай бұрын

Hello if you go in and edit the quality profile you can change the infil% it saves to the quality profile once you change it so you can have multiple profiles for different infil %

@elus89 6 ай бұрын

@@Tenaciouss_BRecently went through the infill settings. Infill density doesn't actually change things like one would expect. Instead you have to change the infill line distance. Any infill density below 81% and low line distance give the results you would expect if you want high infill. If you set it above 95% infill density, Creality Print will give the gcode file zero infill. Confusing as could be.

@JohnDStrand 11 ай бұрын

First! Another Slicer! OH MY GOODNESS! One slicer to rule them all!

@Zachary3DPrints 9 ай бұрын

Really? 😂 I think there are some better ones out there, but learning and mastering a few more doesn't harm

@rmgrimshaw23 11 ай бұрын

They just need to change out improve the camera angles for this slicer. It’s frustrating at times. It’s a little slow too but other than that I don’t think it’s terrible.

@Zachary3DPrints 9 ай бұрын

Great idea, I didn't had this issue with the camera.

@djchemical 6 ай бұрын

hold middle mouse wheel to move it around

@rmgrimshaw23 5 ай бұрын

@@djchemical Well shoot, I have my wheel button setup to open a new email page 😂😒

@fusonbradly 9 ай бұрын

Ive never successfully uploaded a sliced model from creality print to the creality cloud

@Zachary3DPrints 7 ай бұрын

Sorry for my late reply. Is your printer connected to Wifi and binded to Creality Cloud?

@elus89 6 ай бұрын

Yeah It crashes the program. If you want to upload you have to go directly to the cloud website via a browser. I'm surprised the OP didn't mention how bad the Creality software is.

@Decoda3D 7 ай бұрын

Where’s the vase mode 😭

@Zachary3DPrints 6 ай бұрын

In my latest video about this slicer I did show that. You can check it out here: kzfaq.info/get/bejne/o7iCecl-x73SdJ8.htmlsi=o2K5YjJYC8CygM7i

@officialWWM 6 ай бұрын

This is terrible. Doesnt work, hides the mouse pointer and crashes all the time!

@Zachary3DPrints 6 ай бұрын

Oh, that is really bad... which OS do you have and which version of the software do you use? Maybe I can help you out

@officialWWM 6 ай бұрын

@@Zachary3DPrints thanks. I’m using Windows 10 and I have the latest version of the Creality software.

@TheTrueMufasa 8 ай бұрын

This slicer is the worst. Keeps crashing, no support blocker. overall trash.

@Zachary3DPrints 7 ай бұрын

Oh that is sad to hear buddy. I hope you have some other really great slicer! Which one is your favorite?

@TheTrueMufasa 7 ай бұрын

i use Cura, even if its does not have a profile for my K1 MAX. It says its 15 hours, but my K1 is 6 hours printing it. Thats the only downside of using Cura without profile...not knowing how long print will be.@@Zachary3DPrints

@skorch91 7 ай бұрын

I’m running Creality Print on a 2015 Mac - that is a little slow for processing the slicing, but it works fine. I like this slicer - I used Cura and can find the custom settings and custom support options. I’m sure they’ll be adding features. If that’s what makes this printer work, I’ll stick with it. I’m not thrilled with their Cloud - I couldn’t get a model to upload - I’m fine with a USB.

@elus89 6 ай бұрын

Not wrong at all. The upload function crashes every time. The model store is obnoxious, filled with nude stuff that will bump to your default page. The infill settings are backwards, don't touch density, instead go with infill line distance (if you dare). The app bogs down after you have changed view a few times. The support options ruin the print quality on anything it gets near. The brims are too sturdy, you have to hack your model up with a knife to get them off. Not sure what my options are with a Ender 3 V3 KE...

@TheTrueMufasa 6 ай бұрын

I just started using Cura, even if the K1 MAX Profile isnt there. The print time goes tru the roof, but its never that long. Cura is so mutch better@@elus89

@cybergnetwork588 5 ай бұрын

TBH, I've had much more success with Creality Print than Orca Slicer. Better quality prints. Ender 3 V3 KE.

@Zachary3DPrints 5 ай бұрын

I can imagine that… these profiles in Creality print are added by Creality themselves… if they p put some time and efforts in other slicers as well, more users can use their favorite slicer and their new printer. Until that time, I’ll make these videos to keep people going with their new printers from Creality. Btw, great printer, the KE!