CREALITY'S ENDER 3 MAX - NEO - QUICKSTART GUIDE

No video

CREALITY'S ENDER 3 MAX - NEO - QUICKSTART GUIDE

Рет қаралды 20,617

3D Printing Canada

Күн бұрын

Пікірлер: 29

@MineSplosions Жыл бұрын

12:34 By default Cura slicer will not load the bed leveling mesh after leveling, you have to go into the printers start gcode and add "M420 S1 Z10" with no semicolon, on the line after G28 or G29. Otherwise the leveling mesh is not loaded. A semicolon after M420 also stops the code from executing for some reason, despite all other lines having one. M420 is the command for loading the mesh S1 is the enabling of the mesh Z10 tells the printer to stop using the leveling mesh after layer 10 and even out the layers as if they were on a flat bed. Struggled with this for a couple of weeks myself after buying a BLTouch. Hope it helps anyone else running into a similar problem.

@nedh8493 Жыл бұрын

this just saved me a ton of troubleshooting, thank you so much!!!!

@MidnightMaker Жыл бұрын

I just used your video to setup my new printer. This was the best video covering the setup. Thanks!

@khaosbane Жыл бұрын

Thank you, your leveling explanation was perfect.

@ruthlessluder 29 күн бұрын

How do you feed the spool? It's not in the manual nor in this video.

@D2booo 7 ай бұрын

I got a question my filament won’t go in

@ibrahimalrabiah1179 7 ай бұрын

You need to cut the tip of the filament in 45 degrees angle

@1965ryansmith 7 ай бұрын

Thank you very much you have helped me out lot

@josephjolly1936 Жыл бұрын

Thanks for the video.

@JimmyJohnson-ub4rt 9 ай бұрын

great video thank you

@BSSC1775 Жыл бұрын

thank you so much

@SEARCHANChan 6 ай бұрын

If ur printer keeps rebooting The problem is most likely on the power selection in the back

@SEARCHANChan 6 ай бұрын

US only outputs 115 v but printer may be set for 230v

@3Designer_col 4 ай бұрын

I don't understand why you don't just choose 'disable steppers' to make the movement.

@AndrewAHayes Жыл бұрын

Considering the price of electricity these days a faster printer makes more sense.

@ctako13 7 ай бұрын

Any suggestions that are in similar price range?

@AndrewAHayes 7 ай бұрын

@@ctako13 No Idea, I gave up on watching the bed slinger scene ages ago

@bipsendk 9 ай бұрын

What size spring steel PEI sheet would have to be used on the Ender 3 Max Neo ?

@nagarajaprasad8591 5 ай бұрын

Does this have 1 part cooling fan or 2 fans?

@Mystery71145 5 ай бұрын

When i press preheat pla the printer just turns off and then on but it didn’t preheat the pla

@shriek0lego160 2 ай бұрын

Idk if you alr got it working but its the back the red thing that says 115v and 230v I just changed it to 115v and it works 😊😊

@gburger011 5 ай бұрын

i just ordered mine, would there be any issue with me setting up mine with the same measurements has yours?

@dezmas9332 5 ай бұрын

There will be issues, the one I did for my dad required around 1.57 Z offset with a lot of corner adjusting, use your paper and once it seems to stick a lot, you'll have to keep raising until it just about doesn't stick or else it will likely scratch in my experience, though we haven't printed yet due to lack of consumables

@kinvotime490 3 ай бұрын

Until you try to print Petg and the higher temps causes your bowden tube to swell and you can't print. So you upgrade the hot end but there are very few choices for this model. However, you get the Sprite anyway only to find out Creality doesn't support this combination anymore. You think no big deal and search for firmware from other sources only to discover you got the TJC board that hates being upgraded. Now you need to get klipper and do more mods to get you Ender 3 Max Neo to work and realize you have now spent as much money and more time than if you would have just bought the higher end printer from the beginning.

@LordRavensWorld Жыл бұрын

I love the stuff that you do and would love to be able to promote anything of 3D Printing Canada on my KZfaq channel, it would be so awesome to collaborate.