Main Four Power Problem Of Induction Cooker Have To Been Seen In This Video.
Пікірлер: 796
@teknerds4 жыл бұрын
You are good, but you shouldn't recommend shorting the fuse. That is a potential fire hazard, should anything go wrong. In places where there are load shedding and other power grid changes, the device could run over it's ratted current specifications and overheat, possibly causing a fire if there are flammable materials near the device. It's a good video however. Next time, consider talking and explaining using your voice to emphasize and clarify your troubleshooting, fault checking, meter usage and soldering to replace the parts...
@wamperth3 жыл бұрын
Very good video. Personally the music is overpowering, so to watch I turned sound off. Many videos are way more enjoyable without music, this includes professional movies. The one I am waiting for part to repair, the fuse is rated higher than the mains trip, (20A fuse, 20A IGBT, 16A mains trip) so the mains turned off, also the unit was not in use but connected to mains. So in some units if the IGBT goes short, either the fuse blows or the mains trips. Added you to my fixit section and a thumbs up.
@CreativeWorldPro3 жыл бұрын
Noted!
@Vex916T Жыл бұрын
Seriously clicked on this video to fix my induction cooker... but after 30 seconds of listening I decided to drop some molly and dance to this song all night long!
@nd.kushwaha86694 жыл бұрын
आपको दिल से धन्यवाद सर, आपने बहुत अच्छी जानकारी दी
@xerejuneseve63336 жыл бұрын
Thank you !,in my free induction heater it was bad fuse ,IGBT and rectifier.Now i hawe cooker for 8$.
@pramodsdamre66495 жыл бұрын
Thanks for the rip sirji. Me ek refrigeration technician hu bus induction ka kam aap jse achee log you tube dalte ho to apse hi thoda thoda sikh raha hu sirji
@gilthermovp5 жыл бұрын
Cara vc é muito bom, um grande técnico em eletrônica, pena eu não falar inglês. Sou do Brazilian
@CreativeWorldPro5 жыл бұрын
thanks a lot
@wesleyrm Жыл бұрын
Huehue brbr bom dia man!
@vasilepop1444 Жыл бұрын
Muito bem
@EndstyleGG6 жыл бұрын
Good solution, if the fuse keeps popping just get a bigger one, great way to start a fire
@mr.unknowngamerz79553 жыл бұрын
Yes it blasted
@suryaprakashbellary87733 жыл бұрын
Very nice demo .Really useful. Thank you
@CreativeWorldPro3 жыл бұрын
You are welcome!
@teknerds4 жыл бұрын
Another possible problem with these cookers could be the thermistor, and this could be for checking the temperature of the cookware by checking the temperature of the base of the cookware, using a thermistor under the surface or perhaps the glass could have an embedded thermistor, which would mean that the repair would involve replacing the glass with a manufacturer part
@CreativeWorldPro4 жыл бұрын
thanks
@muhammedsabirk7 жыл бұрын
I found several videos about this topic but I think this video more informative
@CreativeWorldPro7 жыл бұрын
thanks
@daynite18822 жыл бұрын
Looks like, overall though if you're in the field like me, it would be simply replacing the board since we're not allowed to do weldments in operating commercial kitchens. But at least now I know HOW to fix it with a soldering kit.
@Bloggerbhat5 жыл бұрын
Your 1st 3 problem solving are very nice but 4th one are not a correct solution's...need replace fuse with proper amp for safety of PCB & also user
@maheshnakh4 жыл бұрын
How to solve e4 error...my induction works fine in shop but shows e4 error in home
@MohamedMohamed-df5uc4 жыл бұрын
@@maheshnakh pa-♧08], ♧1 [.¿
@badrinarayankumawat37773 жыл бұрын
H
@amintaleghani21102 жыл бұрын
@Creative World, Thanks for your video. when i use my induction cooker it will cause the voltage in the house to start fluctuating. could you please advuce what could be cause/problem?
@WilliamAshleyOnline2 жыл бұрын
nice I had some plastic between coil spacing melt, wondering if contact between coil points will cause a short.. the heater is flashing on and off, and prior to me moving the coil that seemed to melt together a bit was not powering on at all.
@CreativeWorldPro2 жыл бұрын
Most likely
@sharonfung17444 жыл бұрын
Sir - thank you for video. I have 3700W 11" Induction coil, it seems to output very low - boils water same speed as 1850W burner. Could problem be with coil - coil still heats pan - or the generator board? It is interesting power is almost half - could somehow one item be damaged on generator ? Thank you
@ashoktripathi74586 жыл бұрын
Useful information,Thanks.
@CreativeWorldPro6 жыл бұрын
welcome
@SubedarSahabAK2 жыл бұрын
Nice and detailed information Can avoid music, Well done , keep it up
@CreativeWorldPro2 жыл бұрын
Noted
@ratnachandawa99165 жыл бұрын
Thanks for your suggestion I got the fault
@CreativeWorldPro5 жыл бұрын
congratulation,
@karthickkr95145 жыл бұрын
Super use full thank you
@sonofusion7 жыл бұрын
while it works, bypassing the blown fuse might not be the best way to fix it. it is better to replace the fuse. anyway, great video. I've fixed some induction cooker previously too.
@CreativeWorldPro7 жыл бұрын
you say right,,, i use some shortcut method to repair the induction cooker
@CreativeWorldPro7 жыл бұрын
you say right,,, i just try my best to see some shortcuts ,,,about the power problem of induction cooker
@basavarajumudhiraj31097 жыл бұрын
Creative World
@wigglypaw5 жыл бұрын
you are correct to replace and not bypass.
@ypjani6693 жыл бұрын
Sirf music hi bajaoge ki kuchh bolke samjaoge ki kyaa kar rahe ho. Agar ham sab samajhte hai ,aisa mante ho to aapke video dekhane ki jarurat kyo hogi?
@melikrasniqi15114 жыл бұрын
Could you make an induction (metal) heater from this?
@anandaraj33664 жыл бұрын
after 2 years use , the i-stove errors E7 after few minutes usage .what may be the problem?
@hariharan9776 жыл бұрын
Thanks, helpful video
@jacintolopez5344 Жыл бұрын
como es posible hacer ese puente en lugar de cambiar el fusible ademas al cambiar el transistor yo cambiaria los iodos rectificadores y claro hace falta una buena limpieza en todas los equipos pero quiero pensar que solo nos esta enseñando las posibles fallas mas comunes y despues hizo los servicios completos . gracias por compartir tus conocimientos . saludos
@CreativeWorldPro Жыл бұрын
thanks a lot
@ridjonful3 жыл бұрын
I agree that the 4th repair tip is not a good practice. The reason we have a fuse is for safety - to prevent electrical fault that may cause fire. Always replace the fuse with the correct specification. Lack of info as when certain electronic parts became shorted, automatically the fuse should blew up or get busted (busted fuse).
@SameerAnsari-sg5xs6 жыл бұрын
Great work bro, keep uploading more, ur like number is 786, don't want to disturb that lucky number
@CreativeWorldPro6 жыл бұрын
ok,,bro
@rodelle2024 жыл бұрын
does a good stove usually have continuity ? i checked my ih stove and the fuse is blown. i replaced the fuse and the stove have continuity.
@jonessoares68962 жыл бұрын
Great work sir thanks regards Jones Soares goa
@m.ramesh21524 жыл бұрын
Useful video. Thanks But the instruction letter color not suitable for reading. Please choose good color for fonts
@CreativeWorldPro4 жыл бұрын
ok
@rubemorada35614 жыл бұрын
my induvtion no display i change rectifier and igbt but ok again i assemble ok running only 2 seconds automatic off no heating but has power;;what do to fix thank you very MORE POWER TO YOU GOD bless
@irfanmestri11777 жыл бұрын
dise vidio veri help full for me tq
@canbeyhan7538 Жыл бұрын
thank you for the video, my cooker gives a fan noise for 1 second as soon as I plug it then immediately stops and no light and dead.. What do you think the problem is about?
@CreativeWorldPro Жыл бұрын
power problem
@bcburnettcom4 жыл бұрын
what did you do to the top of that unit? Bury it in a landfill for a year?
@rpk55684 жыл бұрын
NEVER take anyone's advice when they fix something by shorting the fuse. You'll void your homeowners insurance if the thing burns your house down.
@KING4SNIPR2 жыл бұрын
🤣🤣🤣right
@amolnarwade44022 жыл бұрын
.moolloomm
@hornos27hotmailcom6 жыл бұрын
En el minuto <a href="#" class="seekto" data-time="232">3:52</a> muestra es un tubo de caucho de silicona de alto voltaje para pegar elementos como socket yugos y demas partes moviles, el debio utilizar grasa de silicona disipadora de calor para el IGBT, quimico que es totalmente diferente al utilizado para la reparacion de la estufa de induccion.
@Richag884 жыл бұрын
ясно и без болтовни(+1)
@simontwo8884 жыл бұрын
thanks will try checking
@impossiblenothingkhan5347 жыл бұрын
Nice video sir very helpful thanks
@CreativeWorldPro7 жыл бұрын
welcome
@wigglypaw5 жыл бұрын
Thank you. I would have loved to do this work.But in school, girls were not taught basic life skills and how to fix and make a living. We learned how to make , vanilla pudding, cinnamon toast. Sewing a skirt- which I got a D in which is almost fail. The reason why, my engineering brain said the full skirt mafe me look like an umbrella, so I took the skirt apart the night before, and learned pleating with mathematics for a circle, and then stitched from waistband down exactly 7 inches. Omg it so beautiful and perfectly sewed. That was in 1965. I recently graduated from Academy of Art University, - via computer classes with physical tests and items sewn and mailed in. I graduated Summa Cum Laude. Hahaha! In 1965 I also took the Air Force tests to see what you excell in for your life work. I wanted to be a farmer and have horses, and tried to answer every question that way. HAHA. It came back I was in the Top 10% of the U.S. in Engineering brain skills. After school the Air Force really wanted me, but my parents told me no. They were very constrictive parents. Working at a plant nursery was very good, in their idea, or being a secretary,so I did that. I also had a horse from whem I was 11 years old and never been without one, and I worked as a jockey at Belmont Raceway, but of course my parents would not let me go with my stables to Florida for the winter. I still use my engineering skills to troubleshoot in my mind and find solutions. I think my life was a wasted one, I could have done everything . But, I was a “good daughter” and listened to chauvinistic parents and misogynist father. I would do it all over again if I could. And all these deep thoughts arose from watching a induction cooker being fixed. Thank you so much for not throwing these things out that can be made better than new once again.
@mzlah18204 жыл бұрын
Better if u r slow in explaining.
@offgridlife84486 жыл бұрын
thanks
@aasthaenterprises22735 жыл бұрын
nice video dubara banaye to iski plate ko badalne ka tarika zaroor bataye
@CreativeWorldPro5 жыл бұрын
ok
@subhashchanderdhiman55976 жыл бұрын
electric Point.sir aap ne sb code btay pr E6? code ke fault ke baare me koi video nahi bnai kirpa iske baare me jldi se batay ya videos bnai bnai
@rpdharmasena4946 жыл бұрын
May I get any idea about what is the resistance of the cooker coil???
@akshaymaldhure7 жыл бұрын
Hello, thanks for this video. Trying to switch on the induction cooker blows the fuse away in my house. What could be the issue?
@CreativeWorldPro7 жыл бұрын
try changing the rectifier of induction,,cooker
@electricalcoder30254 жыл бұрын
@@CreativeWorldPro same problem but the fuse goes off only when the coil is connected to the heater ...when I removed the coil and put the fuse it was working fine...when I again put the coil fuse blows off...and resistance of the coil is showing just 5-6ohms only ...what should be the reason
@mohiuddinshah55586 жыл бұрын
sir great work I love that sir in my induction it show E4 what is the fault sir plz reply sir it is prestige induction sir it has two heat sensors sir I am waiting for your reply
@CreativeWorldPro6 жыл бұрын
regestor problem hoita piara
@bnbhatta7 жыл бұрын
It wd have been better if steps were shown to guess/detect the faults - i.e what are the symptoms to conclude that the transistor or the rectifier or any thing else is defective.
@CreativeWorldPro7 жыл бұрын
there may be beep sound,,or no display on the induction cooker
@dadasochougule26656 жыл бұрын
prestige induction cooker has only been sound after on condition but no display
@nashwanashwa62994 жыл бұрын
My prestige induction cooker some time working. But suddenly off. After some time it is working.
@Petalheart38615 жыл бұрын
thank you
@joaopaulosouza-espiritualidade6 жыл бұрын
Hi, a great vídeo. Could you help me, my induction cooktop IS needing repair. All part funciona, but not heat sufficient. Do you know what kind problem?
@CreativeWorldPro6 жыл бұрын
you should check the heating coil
@joaopaulosouza-espiritualidade6 жыл бұрын
@@CreativeWorldPro thank, do you know how can i check? I checked with The multimeter and The Signal continuity is ok.
@masterbasu5 жыл бұрын
Do tarikha hai 1. Capacitor 5mfd/400 volt replece. 2 . Heat control preset 203 k replece job done
@aditya1986jain5 жыл бұрын
It is not a very easy to check the power rating of induction cook top as it works on the principle of induction not on the joule heating, i can suggest an alternative method to chek the rating of a induction cook top. To check the power rating of the induction cook top. Let the rating is X, Now take 1 lit of water and record the initial temperature T1 degree Celcius, Now pour this water into a steel (or recommended ) flat base flask ,( base should be nearly equal to the specified area ), Keep this water for heating for 1 min (60 seconds in 100 percent mode) stir it and record the temperature T2 degree Celcius. Now you can use 70*(T2-T1) to find out the rating, this value should not be less then 75 percent of the rated value.
@tntpillaithulaseedharanpil30253 жыл бұрын
Very good, thank u bro
@CreativeWorldPro3 жыл бұрын
Welcome
@tommyp99894 жыл бұрын
I have the ihe3790 240v after clean it let it sit for a week before I plug in the cable. No power on display . Remove the housing found the fuse blown. Put in a new fuse 15a 250vac with is the original. I replace the same fuse plug in. Fuse blown again. What should I do now?
@salvador541005 жыл бұрын
one of the two condensers of 8 microfarads is destroyed, can it be the cause of another electronic component? thankyou very much.
@bhupendrakumarr69272 жыл бұрын
For common man needs what are problems and cost for repairs with cost of spare Finally where spare available
@dhananjayas68873 жыл бұрын
U R brilliants sir ji. thank u ❤️.
@CreativeWorldPro3 жыл бұрын
So nice of you
@AbdulKalam-ge8pu3 жыл бұрын
Upar ka Upar Kaya Shisha Kahan Milega Upar Kaya Shisha Kahan Milega
@AbdulKalam-ge8pu3 жыл бұрын
Iska Saman Kahan Milega induction chulha ka Upar Ka Sheesha yah ka saman Kahan Milega kahan per iska market hai
@us.eth.p2 жыл бұрын
i need to know that in fourth problem... while rectifying it which wire you used to join the fuse by replacing the old faulty one
@danieledgardopalomar78124 жыл бұрын
con cuanto de tension continua funciona?
@eshivakumar59014 жыл бұрын
Super bro we want more than video
@jaik28194 жыл бұрын
Main LED is blinking (ON/OFF switch) and beep sound is also working, but when I press the other buttons then there is no action. What might be the issue. Recently I have washed the stove with water (In top of the panel, I think few drops got into inside).
@CreativeWorldPro4 жыл бұрын
you should wash panel board with cleaner and replace all switch
@needi513 жыл бұрын
Great Video! Very helpful!
@CreativeWorldPro3 жыл бұрын
Glad it was helpful!
@magicalempire6 жыл бұрын
wow how about if when switched on the electric in the house goes off? any ideas
@CreativeWorldPro6 жыл бұрын
you should check Mosfet And Rectifier Diode
@waynerwalber6310 Жыл бұрын
In step 4 did you leave the bridge on the fuse line? Wouldn't we have to identify and correct the reason for the blown fuse and replace it with another of the same current? Thanks. I already liked and subscribed to the channel.
@CreativeWorldPro Жыл бұрын
I did not have fuse, at that time. For that, i follow that method. But everybody should use fuse.
@waynerwalber6310 Жыл бұрын
Ok.
@manjunathga16966 жыл бұрын
The video really informative,My induction top as i switch on the mains it get tripped off ,I checked the power supply chord, it is not fused .What could be the problem ? and how to set right?
@muthukumarselvaraj25504 жыл бұрын
transitor change me
@zuchamotungoe68175 жыл бұрын
Part 4 i try but when i fix with wire the wire blows and my MCB 16 ampere shut down so i would be happy if you make video for this symptom.
@CreativeWorldPro5 жыл бұрын
sure,,i will try my best
@RioRio-pc5vl6 жыл бұрын
is there is any polarity in filter capacitor mpk x2 and mpkh sh. it is polarized or not???????? Sir
@spadixsharma46745 жыл бұрын
Sir, my induction gets on!! But doesn’t sense the cookpan!!! Instead produces sound in a regular interval... when paused the sound disappers!! Can you help ?
@CreativeWorldPro5 жыл бұрын
what is the main problem ?
@freakbot10563 жыл бұрын
Induction cooker making a regular beeping while a pan is not placed on it while active isn't itself a problem but in most cases be part of its programming . The things I do in similar situations are ; 1) Resolder the ground jumper line . 2)Check the box capacitor 5 muF,(make Shure to remove them and check underneath it) 3)check the 8550 and 8050 transistors . 4)while plugged in series ,put multimeter in DC and while placing negative probe on Bridge Rectifier negative ,check the resistors to see if any of them are open .
@bikashbarua.38862 жыл бұрын
Fantastic solutions.
@CreativeWorldPro2 жыл бұрын
Glad you think so!
@petesmith64005 жыл бұрын
Awesome work =)
@danielpoirier66843 жыл бұрын
I have a whirlpool induction hob, error code e60 on the 4 ron quesque that does not work
@user-ue2st4jm3k2 жыл бұрын
Thank you But i have different problem It is working for a second or more sometime for 4 minutes ...then return to standby ..or start on off by himself or time going crazy
@lalrinkimaralte42354 жыл бұрын
Philips HD4920 problem. Leds are lighted but I cannot switch on. I replaced the switch but the problem still same. What may be the problem? Please suggest.
@zmsky46667 жыл бұрын
Thank u my problem is solved
@CreativeWorldPro7 жыл бұрын
congratulation
@ZehrilaChilgoja4 жыл бұрын
Can u explain use of silicon rubber paste.?
@jburdman78 ай бұрын
should be thermal compound NOT rubber. Rubber is a thermal insulator
@gangirin6 жыл бұрын
hai.....my igbt got bursted, watching your video ,i changed it myself, but it worked only for around 15 minutes and then again got short, the original board had igbt n1600, they have mentioned 20a and 2000v in the circuit board, the replacemment igbt that i got from store was 1b16aj/fga25n120antd... can u please tell me whether the replacement given is okay , then the problem must be in my soldering, thank u.
@CreativeWorldPro6 жыл бұрын
you need to use the same Value IGBT
@ranadheerreddy61924 жыл бұрын
I'm having heating problem with my induction stove can you help
@catsoup39766 жыл бұрын
Really appreciate this but the problem I'm facing is not here.
@CreativeWorldPro6 жыл бұрын
thanks
@narendrasolanki67617 жыл бұрын
your presention good
@rajakumarsingh3145 Жыл бұрын
Bhai new induction me ceramic vs glass kon better hoga Prestige ka ceramic atlus 3.0 1200watt. Vs pigeon crystal glass favorite ic 1800watt. Kon accha hoga ?
@CreativeWorldPro Жыл бұрын
Pigeon crystal glass 1800 watt will be better
@saiprasad80012 жыл бұрын
When i use a neon tester to check the stove top or the vessel placed on it the neon glows. Is that normal? I used the voltmeter to check the voltage between the vessel and Earth/ground and it shows about 30V.
@CreativeWorldPro2 жыл бұрын
no problem
@roykirich4 жыл бұрын
nowadays some electronic component manufacturers use iron instead of copper for example in resistors, could the magnetic property in them make them heat up especially those near the copper coil induction element. using a neodymium magnet will tell you if its pure copper or iron used.
@CreativeWorldPro4 жыл бұрын
Yes, absolutely
@jackberi95845 жыл бұрын
VERY GOOD VIDEO, you could also speak would be better, nice work
@CreativeWorldPro5 жыл бұрын
sure,
@leelathambiraj53823 жыл бұрын
My induction stove is connected to power when switched on .the light glows.but further process does not go.what am I to do.pl.expain
@jitendrapradhan46044 жыл бұрын
Thank you
@pkadram6 жыл бұрын
thanks so much
@CreativeWorldPro6 жыл бұрын
welcome
@ROXAIKI5 жыл бұрын
Podrías traducir al español gracias
@CreativeWorldPro5 жыл бұрын
no
@alaguayyanan33386 жыл бұрын
nice thank-you
@CreativeWorldPro6 жыл бұрын
most welcome
@viralvirusgaming94883 жыл бұрын
Good information sir thanks you
@CreativeWorldPro3 жыл бұрын
So nice of you
@Newkomsan5 жыл бұрын
Hi thanks u
@amitpatel8334 жыл бұрын
Nice, very usefull vidio
@CreativeWorldPro4 жыл бұрын
thanks a lot
@govindpatel39196 жыл бұрын
Super 4 fault repair indection cooking top
@cherryzeng52585 жыл бұрын
cool
@tayyabbagwan91753 жыл бұрын
भाई प्रॉब्लम बता रहे हो या म्यूजिक सुना रहे हो ?
@stuntbikeslovers24073 жыл бұрын
😂😂😂
@shrishyambhagatambala50983 жыл бұрын
सही बात बोली है भाई साहब आपने
@syahbudinharahap50664 жыл бұрын
Kang klo sensor seperti optic dvd putih2nya hancur diakalinnya bisa ga kang
@anumalik19384 жыл бұрын
अच्छी जानकारी। मेरे पास इनलसा का है उसकी एक 22ओम की रेजिस्टेंस फटी हुई मिली। उसको लगाने पर वही दुबारा जल गई व फ्यूज भी जल गया। फ्यूज दुबारा लगाया तो 4007 डायोड जल गया व बहुत आग जली प्लग में। क्या कारण हो सकता है ?
@CreativeWorldPro4 жыл бұрын
loose contract or short circuit.
@94373719446 жыл бұрын
i have a problem.. igbt gonna shorted i replaced it with new one now viper 12a ic is heating i replace new one and s8050 tranistor and 78l05 voltage ic also still heating 12 a ic whats problem and the transformer also heating.
@gladvinsingh54494 жыл бұрын
VERY NICE BRO
@worldpower26 жыл бұрын
sir ji maine induction cooker me diode,igbt, 12a ic naye lga diye h 1850,1820 ke transistor check kar liye h.sahi h,shot bhi nahi h.chalu nahi ho rha h display fan me koi halchal nahi ho rahi h... capacitor par 340dc,or ek prove capacitor par dusri display output socate par chake karne par sab par 340,340 dc bta rha h plz help me.
@siewmailee30583 жыл бұрын
where to buy the fuse for kitchen couture induction cooker C201-20D5
@NickyDIY1015 жыл бұрын
I found Boom!!! when pluged, then open the cover and found fuse exploded. What should I check first?
@CreativeWorldPro5 жыл бұрын
mosfet, bridge rectifier and diode
@electricalcoder30254 жыл бұрын
@@CreativeWorldPro same problem but the fuse goes off only when the coil is connected to the heater ...when I removed the coil and put the fuse it was working fine...when I again put the coil fuse blows off...and resistance of the coil is showing just 5-6ohms only ...what should be the reason
@veerapandipriya27152 жыл бұрын
Super very useful
@hkomar3875 жыл бұрын
पानी गरम कर रहा है पर आवाज, साउंड, मे अंतर है क्या करें