Heck yeah that’s a win

do you have a link?

Thank you!

Those are very great ideas thank you so much. And thank you for taking the time to watch.

Awesome! Glad I could help. Good luck on your band patches. Thanks for watching.

Thanks for the feedback and I appreciate you watching my video! Have a great day.

You bet thanks for watching!

Awesome thank you thanks for watching

Thanks for watching

Thanks for watching

Thank you! Thanks for watching

I used to have a lot of trouble with that to try lighter coats and several coats. Heavier coats tend to bleed under. Also, I use urethane paint instead of water-based, which is a lot easier in my opinion.

Glad you liked it! Thank you!

Thanks for watching 👍

Thank you for watching!

Thank you! And thanks for watching!

I’ve never tried but I couldn’t see why not good idea! Thanks for watching

Just the machines default fine point is what I used. Thanks for watching

I haven’t tried it yet. But I would think it would work just fine. It will be harder to control, but if you could keep your stencil taped down and do a couple passes should work the same as the airbrush. Spray paint just comes out a lot faster So you’d have to be careful. Good luck on your projects and thanks for watching.

I’d do that out of card stock. It is much cheaper and cricut vinyl cutter does a good job cutting stencils on card stock

Thanks for watching!

I appreciate you watching and trying this out for yourself thanks for the feedback! Have a great day!

Sounds like you need a new blade or there’s a way you can up the pressure a tiny bit in the pressure settings. Don’t now where exactly without going through the settings but when I get home I’ll check and I’ll get back with you.

OK now that I’m looking when you select make it in the top right corner make sure your dial is set to custom once you’re done with the prepare menu your click continue. Then you’ll be in the make menu where you select your material. Then in the drop down pressure menu, it’s set to default. Click the drop-down menu and select(more) that will apply more pressure to your cut. Hopefully that fixes your problem.

Not sure never have tried that but I have seen people use a spray adhesive and I have done this and it has worked in the past. Just be careful not to leave any residue on your project. Good to do it on a test piece before doing the actual project. Thanks for watching.

Here is an affiliate link to what I’m talking about. Hope this helps. amzn.to/4acse2Y

I highly doubt that it would work, but you could always try it, but if I had to guess you’re squeegee would catch but not sure haven’t tried this.

Ok thanks for the response!

You can cut 7 but I think if you do 10ml you need a deep point blade.

@reddirtdesigns7021 thanks!

Oh yes sorry about that. I will edit the post. It will be in the description soon. I will also send you the link here in just a second. Thanks so much for watching.

amzn.to/3RvIRj2

Also, I use the 4mil now if you go any thicker, you will have to find a stronger pressure setting, so I suggest going with the 4mil which is what I used in the video.

@@reddirtdesigns7021 thank you!

Wow that’s extremely affordable! Good find thanks for watching

Oh I’m sorry not sure why that is!

I’ve never done that before, but I would go with a sinner stencil material to make sure it can mold around the nail easier, and I would go with a fully transparent to help line it up! Might even try the amzn.to/3KEEI9g this vinyl is sticky on one side which would be great for keeping it in place. Hope this helps I might do some research and figure it out for you. Heck if I figure it out I might even make a tutorial on it. Thanks for watching!

Here is my Amazon link to the airbrush I used and highly recommend. www.amazon.com/dp/B000BQKFAI/ref=cm_sw_r_as_gl_api_gl_i_XJ2NSKW8PE62F5JQEEH9?linkCode=ml2&tag=reddirtdesi08-20

I used the cricket explore air two in this video. And it works really good. Here’s a link to the Amazon machine I used. Hope this helps you. amzn.to/49KeqLT

@@reddirtdesigns7021 thanks!🙏

I’ve never done 5 mm but you might play with the settings and get it to work I prefer 7 mm myself works really well and a Cricut will cut 7 mm

@@reddirtdesigns7021 ..im new to all this. I got the thickness from my 50 star stencil is only 2mm thick. I thought it might be thick be it's not very flimsy.

@@reddirtdesigns7021 ..im try to figure out if it's made out of vinyl or a plastic poster board sheet

Yes, they can be a pain at times. I really like the frisket film I have a video that I show a really cool tricks you can do with it. Airbrush Secret Stencil Technique kzfaq.info/get/bejne/nrmShrl4v6jFlZc.html Might check it out. Tell me what you think is it similar to the way you do it?

@@reddirtdesigns7021 thanks

Thanks for watching