I think too many people underestimate the power of a crimped connection and just assume soldering is always best.
@gusswilder64187 жыл бұрын
For a long-term connection that is to resist oxidation over time, or is to be used in a harsh environment, I would prefer soldering, or soldering the crimped connection.
@eurobum20125 жыл бұрын
dialetric grease will help with oxidation. Flux from the solder will just cause more of it.
@snap-off53834 жыл бұрын
@@eurobum2012 flux does not cause oxidation, its specifically to prevent it during soldering, you think that effect ends after and goes the opposite way? Rosin ACTIVATORS cause the surface of the copper to form copper abietate, which can be confused for oxidation by non-metallurgists. Oxygen cannot penetrate rosin.
@eurobum20124 жыл бұрын
@@snap-off5383 under perfect conditions maybe. Add heat or moisture and all bets are off.
@DaveGamesVT7 жыл бұрын
I now know more about wire crimping than I ever expected to. Thanks!
@augustocharles498 жыл бұрын
This is a Great Tool in order to learn about how to properly crimp your wire with connectors.
@mahendranj34838 жыл бұрын
Very useful , Thanks for the information
@jakubczudek30456 ай бұрын
This is how you demonstrate a true expertise.
@user-nm4bk5rr5b9 жыл бұрын
Thanks for useful information....
@pushpitsuri59899 ай бұрын
Exceptionally Explained👌👌
@rasoulojaghi20012 жыл бұрын
Very goood 👍🏻
@sutejohaksomo31157 жыл бұрын
good information thanks
@jongkeunsong61289 жыл бұрын
excellent...
@jmi9676 ай бұрын
Do the applicator log sheets give the maximum conductivity spec as well as the crimp design range? I could see this as being very useful in the case where conductivity is critical to the application.
@orceshutinoski87504 жыл бұрын
Well, welcome to the ODW ELEKTRONIK! ❤🔥
@marluna_x3 ай бұрын
Holy shitdicks this is so god damn genious
@maninidh54483 жыл бұрын
Firstky thanks for the data My request is about the fabrication process of terminal Thanks
@Lun48124 жыл бұрын
The wire going to the blue ring at 0:15 was not stripped properly lol
@STARDRIVE3 жыл бұрын
Also: 3:59 ¨The area increases proportionally with the diameter¨ False, it increases exponentially ;)
@teconnectivity3 жыл бұрын
Thanks for watching our video and providing your feedback.
@fernandoyamaguchi2 жыл бұрын
@@STARDRIVE Also wrong, it increases quadratically
@STARDRIVE2 жыл бұрын
@@fernandoyamaguchi Last time I checked, quadratically means the exponent is two. So I guess we are both right.
@fernandoyamaguchi2 жыл бұрын
@@STARDRIVE I don’t think so, exponential means that the independent variable is the exponent, 2^x is an exponential function, X^2 is a polynomial function of second order, or quadratical function.
@djdelorie3 жыл бұрын
If the CMA is mm2, why are the calipers set to inches?
@chrisdonnell7200 Жыл бұрын
Interestingly enough, both inches and millimeters are units of length. So a diameter measured in inches still translates into a mm^2 cros section
@calvindekoter21284 ай бұрын
Actually, “circular mils” refers to thousandths (“mils”) of an inch - it is a very confusing unit….
@sobhanathtai18383 жыл бұрын
dear sir please hindi me video provide kro
@transdiego8 жыл бұрын
no this is wrong the yellow wire with the blue terminal is to low you can't see the wires
@gorakhnat5 жыл бұрын
Sir crimper & terminal material gred please inform
@gorakhnat5 жыл бұрын
Please feedback
@roidroid7 жыл бұрын
did i just watch a cult indoctrination video?
@STARDRIVE3 жыл бұрын
The Navy Diver is not a fighting man, he is a salvage expert. If it is lost underwater, he finds it. If it's sunk, he brings it up. If it's in the way, he moves it. If he's lucky, he will die young, 200 feet beneath the waves, for that is the closest he'll ever get to being a hero. A Chief Petty Officer shall not drink. However, if he should drink he shall not get drunk. If he should get drunk, he shall not stagger. And if he should stagger, he shall not fall. And if he should fall, he will fall in such a manner as to cover up his rank so that passerbyers will think he is an officer.