a new 22xx mod for thoes that want more power from their crosman airgun
Пікірлер: 52
@nowthenletmesee11 жыл бұрын
Its ok with an extended probe, not a standard one as the standard will just sit inside the pellet skirt and not push it far enough past the transfer port...
@neilthomas9365 Жыл бұрын
Im going to buy a spare probe and try this and chrono to see what it does. Great idea 👍
@KevinMillard68 Жыл бұрын
let us know how it works out for you
@TigrrrTamer11 жыл бұрын
thanks for the simple inexpensive trick. great advice. hope you got yourself a better webcam since this was done ;-)
@MrYingvar Жыл бұрын
Proof that pushing the pellet into the barrel further than OEM location is a power loss, is that a barrel length increase, results in a power increase. Similar mod is to clock the bolt and cut (dremel cutoff wheel) a slot from tip to the flange. Slot to be inline with port. As in decreasing the bolt tip diameter, it allows increase gas flow and improves laminar flow. This post is 11 years old and it is still relevant, assume job. Also works on 13xx models.
@KevinMillard68 Жыл бұрын
thanks
@KevinMillard6811 жыл бұрын
no it still stays as it would stock all i have done is turn the diameter of the tip down to allow more air flow, i did a test today on my sons 2240 his totaly stock was shooting 418 fps.. with just the mod of the probe it now chronys at 463.5 FPS so thats a good increase for sure..that with a 14.6 grain crosman premier hollow point pellet
@TigrrrTamer11 жыл бұрын
hmmm... now I have to buy a drill press? ;) do they make those hollow tubes that you put on a drill, to make large holes for doorhandles for example, but in a smaller version, to remove material around a piece like this?
@wllm99511 жыл бұрын
Very helpful - I tried it;and it worked as described!
@b57ecv12 жыл бұрын
All makes sense good video.
@tobinfitzl342511 жыл бұрын
i'm on a budget, so I don't want to spend any more money, what do you think about sanding the probe down with a dremel?
@jtchen2210 жыл бұрын
Dude, what an awesome tip. Thank you!!!
@KevinMillard6810 жыл бұрын
your welcome
@tobinfitzl342511 жыл бұрын
great idea, I don't have a lathe or access to one, any other way I can do this?
@pathunting12 жыл бұрын
Thanks great video
@KevinMillard6811 жыл бұрын
no it does not use up any more co2 it only allows whats not getting used to get used and up the power of the gun..
@KevinMillard6811 жыл бұрын
good to hear the info was helpful
@KevinMillard6812 жыл бұрын
thanks have a great weekend
@TigrrrTamer11 жыл бұрын
thanks very much for the great tip! you have this nice lathe to do this with... any ideas on how to do it without a lathe?
@KevinMillard6811 жыл бұрын
If you feel you got the skills then go for it, other wise for 20.00 ill put one in the mail for ya this gets you probe only that's moded you will need a new probe cocking Handel that's threaded, I might sill have a few left of those ill have to check.
@KevinMillard6811 жыл бұрын
well when you use an extended probe you lose speed depending on your mods sometimes it pay more to just leave the probe alone and you will gain alot of power depending of course on your mods.. there are way to many combinations of mods
@screamindimon9 жыл бұрын
Can this be done with a Dremel power tool,and a vice?
@KevinMillard689 жыл бұрын
not that iam aware of i always use the proper tool for the job
@tobinfitzl342511 жыл бұрын
does this use up more co2 ?
@davidgreen2442 Жыл бұрын
Great contends but video focus is blurred
@KevinMillard68 Жыл бұрын
crapy camera tech at the time
@donwadsworth75063 жыл бұрын
Can you make me a power mod for the 2240 that hits roughly 650 fps ? If so what would be the cost ?
@KevinMillard683 жыл бұрын
youll need a 24 inch Barrel and a power adjuster a transfer port drilled to 3.8 mm a really soft but still effective valve return spring bore out the front cap on the valve about 3.4 down and a 2289 hammer spring and a lightened hammer as well as a trigger mod to super lighten the trigger to hair pin trigger sensitivity
@KevinMillard6811 жыл бұрын
glade it helped you
@KevinMillard6811 жыл бұрын
thanks
@KevinMillard6811 жыл бұрын
you can buy one from me , i have several left in stock, in .22 cal
@xiavue26068 жыл бұрын
hey bro i have a 1322 crosman with a 18" barrel is a power adjuster work on it
@KevinMillard688 жыл бұрын
hi there yes the power adjusters will work on all the 13xx and 22xx series crosman guns keep in mind the power up is a sweet spot what your going is adjusting preload but to much is bad to little is bad so its all about finding the right spot then lock it in and your good to go with all other present mods
@ralphreynolds26216 жыл бұрын
House trailers
@jeanclaudeboutique65266 жыл бұрын
Wouach.....!!!!!!
@KevinMillard68 Жыл бұрын
english dude
@devinthebodeau868210 жыл бұрын
Awesome video. Great easy free mod. I have a 2289 with a 12" barrel and average fps of ~482. With your mod i took my probe down to 1mm -1.25mm and was windering about where you think the fps will be now?
@KevinMillard6810 жыл бұрын
the mod gives you approx 20 to 30 fps gain
@devinthebodeau868210 жыл бұрын
awesome. thx
@KevinMillard6810 жыл бұрын
Devin Thebodeau your welcome
@Skaetdude9 жыл бұрын
Hi...I'm looking for one of these!Any more for sale?Have Paypal or EMT. Thanks
@KevinMillard689 жыл бұрын
Skaetdude i dont do mod parts any more sorry man check out the airgun fourms
@KevinMillard6811 жыл бұрын
auctually i have a 1080p HD camcorder now take money you know every one starts some where
@KevinMillard6812 жыл бұрын
your welcome
@larryeyster80788 жыл бұрын
You showed us what you did but not how you did it.
@KevinMillard688 жыл бұрын
+Larry Eyster if i show you everything how will you ever learn anything
@KevinMillard6812 жыл бұрын
your welcome galde to have been of help
@bienvenidojr.cabrera16763 жыл бұрын
Pls improve all your presentation. It's blurd
@KevinMillard683 жыл бұрын
kinda hard this was done long time ago and thats what they say thats life and i cant make everyone happy but most are so oh well so sorry that the video bothered you this was done along time ago and tech was was it was then
@KevinMillard6811 жыл бұрын
i sell them or you can learn how to use a drill press like a lathe
@Pongo132010 жыл бұрын
Do you still have these for sale? I can send you a bank issued money order, you can cash it first then mail me the part - hell Ill send you cash if you want.
@KevinMillard6810 жыл бұрын
sorry man i got rid of all the mod parts when i got rid of my guns.