Cub Cadet 102 Rustoration clutch rebuild pt 1

Рет қаралды 9,888

2 жыл бұрын

We address a clutch slippage problem in a cub cadet 102. Initially thought it was a pressure plate issue, turns out it was much more than that. We got it fixed only to find another drivetrain problem. We’ll address that in the next episode. Thanks for watching!

Пікірлер: 28

@bighoss7790 Жыл бұрын

Super helpful. Im building a puller with the same 3 pin style clutch and i bought the tractor as a roller and couldnt figure out for the life of me how that clutch worked, this helped a ton and made me realize what a money pit i bought

@karnesmotorsports Жыл бұрын

Lol money pits for sure! I have cub 3 pullers for my kids. Glad I could help! Thanks for watching!

@bighoss7790 Жыл бұрын

@karnesmotorsports actually I was the one with the 7790 diesel at Pike, that's what I'm putting the cub rear in. Ended up having belt slip and it was my weak link so I can't add any power till that's fixed.

@bighoss7790 Жыл бұрын

@karnesmotorsports you wouldn't have any pressure plates kicking around would you? I'm thinking mine are pretty badly pitted up just from the exterior look, I havnt torn into it yet.

@rodeleon2875 Жыл бұрын

you have a gem there. creeper and headlights. nice options. i've been picking those old narrow frames up when i see a good deal. i have a 100 that needs the clutch among other things. thanks for the video. helps a lot. i really like how you took the front end and hood off all in one clip. makes it a lot easier to straighten/shim it when going back on.

@karnesmotorsports Жыл бұрын

Thanks! I’ve never had a creeper before, it is pretty handy. I didn’t really realize not a lot had headlights. I don’t really know why I bought this tractor, but it’s come in handy. I put a sleeve hitch on it, got a snow blower for $22 from a local auction. It has the cleanest narrow frame deck I’ve ever seen. I was snagging them up whenever I found a good deal, it’s getting harder to find a good deal on one. Yea the hoods can be a pain when taken off the grill. Just gotta watch your fingers, it’s a heck of a pinch point, I learned the hard way! Thanks for watching!

@fredst.george5311 Жыл бұрын

Nice job showing the works of a clutch. I’ve been looking at ever 16:56 video trying to find the proper way to install those 3 small springs that go on motor side of clutch. Your video showed me exactly witch side goes towards motor.

@karnesmotorsports Жыл бұрын

Glad I could help! Thanks for watching!

@TheCanadianBubba 2 жыл бұрын

Nice work, almost looked pitted like the disc rusted to the plate somewhere along the way. Best days to you and your family 👍🏼

@karnesmotorsports 2 жыл бұрын

Yea that’s what I’m thinking is it rusted itself together at some point. The guy threw a new disc in it and then the spring broke.

@Noah-zs7uk 5 ай бұрын

Nice work I'am working on a 104 pulling tracter

@karnesmotorsports 5 ай бұрын

Cool! That will a good one! Message me on Facebook if you have any questions or need some parts. I’ll help you out if I can. Thanks for watching!

@Noah-zs7uk 4 ай бұрын

@@karnesmotorsports ok tkanks

@Surroundedbyevil368 Жыл бұрын

I bought a 102 at a swap meet Friday it had a brand new spark plug and a fresh oil change I should have been suspicious. I brought it home and after a couple of hours it started smoking and died. Plug fouled you guessed it oil. It had a small gas leak I thought it was the sediment bowl it turned out to be the gas tank bearings in the generator starter are bad but it still charged the steering was so bad you couldn't drive it in a straight line after closer inspection I found that the front axle had been ripped off of the frame and re-welded back on but they did not Square it or true it up. The only thing that does not need attention is the rear axle. So now I have a 102 I'm parting out. I found it it's worth more in Parts than it is whole.

@karnesmotorsports Жыл бұрын

Yea they’re definitely worth more parting them out. It makes you wonder what people do to these to destroy them, they’re tougher than woodpecker lips!! I’ve bought a couple for parts over the years with intentions to sell the parts. I usually end up finding another one and building 1 out of the two. We’ve been using the crap out of this one recently. I scored a snow blower at an auction for like $20, used that a few times this winter, I found a snow plow for the front, I added a sleeve hitch to it. It’s pretty handy! I guess I’ll keep her around. I have a 125 I want to get going the hydro would be handy for yard work. I have another 102 I bought for parts. It had been sitting for years, I cleaned the points and the carb it fired right up and ran. I’ve been lucky on the last couple I’ve bought. Thanks for watching!

@Surroundedbyevil368 Жыл бұрын

@@karnesmotorsports I guess I'll be looking for a parts tractor. I like messing around with them in the garage no one bothers me when I'm in there good video thanks.

@dianasimon2060 Жыл бұрын

Those springs are a tirade springs. Most leave them off

@MINItraktor196 7 ай бұрын

😎👍

@shaungoldsmith8055 2 жыл бұрын

Can I get the info for the guy with the blue spring and other clutch parts? Please iam rebuilding my late grandfather's 102

@karnesmotorsports 2 жыл бұрын

www.zkbrmachine.com his clutches and clutch parts are all we run. Thanks for watching!

@dianasimon2060 Жыл бұрын

I took my shaft out without taking grill off and not move engine. Undo clutch hanger, drive pin out of shaft in front of tranny. That shaft will go out on right side right behind generator.

@karnesmotorsports Жыл бұрын

Good to know! I’ll try it that way next time. Yea those anti rattle springs, this is the only cub I’ve ever owned that had them on there. Thanks for watching!

@Realtruth454 11 ай бұрын

Would you have the part numbers for everything? I need to do the same as you on my 102.

@karnesmotorsports 11 ай бұрын

I don’t have part numbers handy, Go check out www.zkbrmachine.com their website is pretty easy to navigate. I got a driveshaft, throw out bearing, a blue spring, and some 5/8” collars. I used the stock replacement clutch disk that was in it. I’ll go check it out and see if I can come up with some numbers for you. We use kerber’s clutches in all our pullers. They’re the absolute best bang for the buck.

@jamesfogerty3044 7 ай бұрын

Where are youse guys getting parts at? Not much on the old cubs about here.. parts can e difficult… did repower with HF. Any advise would be helpful thanks

@karnesmotorsports 7 ай бұрын

www.zkbrmachine.com makes alot of parts. They make some repower adaptors and the best performance clutch components. I make/modify some stuff myself. Parts are out there. Midwest super cub, Brian’s cub parts also. Thanks for watching.

@dianasimon2060 Жыл бұрын

Let’s try again…those springs are antirattle springs.

@karnesmotorsports Жыл бұрын

I knew what you meant lol! Those springs were foreign to me. We usually pitch the stock clutch/driveshaft and swap in a 3 puck for pulling. This tractor is a neat one to have around, purrs like a kitten at a milk pail! Thanks for watching!