Cultivator Repair - Replacing the Carburetor (Powermate Part # A200774)

No video

Cultivator Repair - Replacing the Carburetor (Powermate Part # A200774)

Рет қаралды 86,388

Күн бұрын

www.ereplacemen... Click here for more information on this part, installation instructions and more.
This particular carburetor is specific to Powermate manufactured brands, including Powermate and Southland. To find a carburetor specific to your model, visit eReplacementParts.com.
If your cultivator is showing any of these symptoms; replacing the carburetor could solve your problem:
1) The engine won’t start
2) The engine dies often
3) The engine runs poorly
4) The engine lacks power
5) Fuel was left sitting in the cultivator for more than a month
eReplacementParts.com part number: A200774
Tools used for this repair/replacement:
1) Phillip’s screwdriver
2) Hex drivers
3) Receptacle for draining fuel (or fuel-line clamps)
4) Long-nosed pliers
5) Wrench set
6) Small screwdriver
Get model-specific repair help from eReplacementParts.com. Learn how to troubleshoot, diagnose and repair your power tools and equipment with illustrated instructions, hundreds of step-by-step repair videos, and our DIY forum. If you have a power tool or appliance problem, we can help. www.ereplaceme...

Пікірлер: 18

@gerorgemcgrath6321 Жыл бұрын

Thanks for your directions

@TheFatPeguinBand 3 жыл бұрын

My problem is the fuel lines deteriorated and not sure which is the in or out??? Can you help me?

@MikeDMADLabs 7 жыл бұрын

Thanks for this video.

@dodgersfnshepard8673 4 жыл бұрын

Can I take the carb off and toss the entire thing in an ultrasonic cleaner? If if the carbs my problem so instead of tearing down/rebuilding I'm trying my best to cheap problem solve systematically

@dalehammond1749 Жыл бұрын

Very clear, thanks!

@francistukesasaperiki8063 4 жыл бұрын

Boss im from Solomon island and I'm very interested if you make a video of how to repair a makita plan that have so much spark coming with the carbon brush .thanks

@Taydrum 4 жыл бұрын

have one of these, just replaced the carb, fuel is clean and pre mixed, has spark, has excellent compression, replaced fuel lines, primes well. Fuel is getting into the cylinders, and ignition is on, will not start no matter what. Not even a cough

@customcutter100 3 жыл бұрын

Apparently he couldn't get it to crank either. Never showed it running. Did you get your's going! Saw one on CL for $100.

@Taydrum 3 жыл бұрын

@@customcutter100 Its toast. The cylinder was scored and wasn't sealing properly, but, putting oil in the cylinder was giving false compression values. Scratch the excellent compression. The carb was fine, the spark was fine. I'm guessing factory emissions spec carb settings were too lean

@a1930ford 3 жыл бұрын

Do you have a specific video of replacing the carb to the 4-Cycle Lawn Edger, P-WLE-0799-F2N, A100626 carb.? I have good spark, fresh non-ethanal gasoline in tank and tank is half full, good compression and yet, no start on this edger at all. It was used only once this past week when I bought it, but suddenly died out and has not been able to be cranked off since. These edgers have a bad history of being difficult to start. I have ordered a completely new carb for this machine, but that was after using starter fluid to give it a boost when starting up. It ran for a short while with this being done to it. I am in the process of cleaning this carb to see if that may work on it, but I went ahead and ordered a replacement, just in case. Again, do you have a video regarding this particular model edger. It is not the same as the unit you used in this video. Thanks.