This video shows the process of shortening a long bed frame to a short bed frame for my 1972 Chevy C10. I used a kit from long shot fabrication. You can find it here: www.longshotfab.com/
Пікірлер: 20
@gregmaggielipscomb92466 ай бұрын
Nice work, your frame is sure in nice condition, I look forward to watching more of your work.
@farmingcars6 ай бұрын
Thank you. The rest of the truck is nothing special, but it's a lot of fun!
@DadbrosGarage7 ай бұрын
Looks good fellas!
@willhart7861 Жыл бұрын
I really wish the f150 was as easy to cut down. Nice job!
@farmingcars Жыл бұрын
Thank you!
@buch26532 жыл бұрын
Yeah
@bikeguy0 Жыл бұрын
Hey quick question. I'm having a heck of a time getting my frame stiffeners into the frame rails, like they are too tall by 1/8" and I have to bend the bottom frame rail to get them in there. It doesn't look like you had any of that trouble. Just checking. I'll contact Longshot but I thought I'd put a comment here. My passenger side must have hit a rock and is slightly bent so I'm having to open the frame rail up just a bit but the other side is just fine and it doesn't fit without a ton of persuasion as well and it looks like yours had a good amount of play to get it to line up correctly with the bolt hold and frame. Thx. Mine is a 72 c10 btw.
@farmingcars Жыл бұрын
I was able to slide mine into place pretty easily. There isn't any extra room though, so if yours was high centered on a rock at one time that could cause it.
@cazuro27622 жыл бұрын
You owe me $25 for this subscription
@MichaelWilliams-sj6lo8 ай бұрын
What size of welder are you using? I'm about to use a long shot kit for my truck
@farmingcars8 ай бұрын
It's 140Amp MIG with shielding gas, nothing special. It's rated for up to 1/4".
@MichaelWilliams-sj6lo8 ай бұрын
Thank you@@farmingcars
@Brandonbaughman2 жыл бұрын
Woo Hoo! Plan a hrpt?!?
@farmingcars2 жыл бұрын
If I can get it ready in time.🤞
@nickle549 Жыл бұрын
What happened with the rear cab mount?
@farmingcars Жыл бұрын
The holes in the jig were 1/2" off from where they should have been. I can't remember if they were too far forward or backward. I measured my parts truck to confirm (I didn't check on this frame before I started) It was an easy fix to the jig. I mainly wanted to mention, in case someone else uses the same jig, to check your measurements before drilling the holes.
@nickle549 Жыл бұрын
@@farmingcars I have the same kit and about to install it. I can't believe it's off 1/2"!
@farmingcars Жыл бұрын
It was just the rear cab mounts. Everthing else was correct. It's possible mine was made incorrectly. All in all, the kit saved me a ton of time and I would buy it again.
@elong8588 Жыл бұрын
@@farmingcars sorry for the problem on the cab mount holes. I'm not sure what could of ended up being wrong on the template. I know this video is almost a year old now, but do you know when the kit was purchased? We have sold over 100 of these and have never had a complaint.
@farmingcars Жыл бұрын
@@elong8588 I would have gotten these in December 2021. It's a great kit and made the job pretty simple.