Cutting the holes! | DIY bow thruster install

Рет қаралды 13,512

4 жыл бұрын

Second video in a 4 part series where I'll be installing a Sidepower 40SE bow thruster in a Beneteau 34 Oceanis.
This episode will cover the cutting of the holes for the tunnel in the hull, preparing the inner for fiberglassing and prepping the tunnel.
If you haven't seen first episode, please feel free to do so: • Finding the correct tu...
Link to more info on fiberglassing
Boat works today: / boatworkstoday
Sail Life: / madsdahlke
Royalty Free Music from Bensound

Пікірлер: 27

@pierre-rose7783 2 жыл бұрын

Everyone should install a bow thruster !

@BevMtnGds Жыл бұрын

Nice job and great info on the carbide blade.

@OrvilleHarmison 4 жыл бұрын

Now I am wondering if my 40 Oceanis is double hull to? I guess I will find out when I start cutting holes in her, at least I won't be surprised if it is. I am saving each of the videos in this series for a instruction book for when I put my bow thruster in. Thank you so much for making this video series.

@jacobkollerup 4 жыл бұрын

You are welcome. You should be able to check if you have a double hull under your cabin sole. If you see bare fiberglass, then it´s probably a sandwich construction. If it´s nice gelcoated surface and sound hollow, then you have the same as mine. How old is your boat? Mine is a 2012, so fairly new

@OrvilleHarmison 4 жыл бұрын

@@jacobkollerup Mine is a 1996 and yes it is gel coated in my bilges but it doesn't sound hollow. Guess I will find out when I start working on it. All I am waiting on is for this pandemic to be over. Be safe out there.

@johnyalowica8423 9 ай бұрын

Hello! I not sure where to find the link for tool you used to mark your holes! Do you remember where you found the link? Cheers John

@jacobkollerup 9 ай бұрын

Hi John. It’s my own design that I 3D printed:)

@alejandroborobiamoreno6070 4 жыл бұрын

Very nice video thanks for sharing. I am a new into owning a sailboat. Last November I bought an oceanis 323 from 2007 also in Copenhagen area! Can't wait to put it on the water. Mine has already installed a bow thruster, but I am thinking to install a windlass. Do you think I could power the windlass from the thruster battery? If you are preparing your boat for the season I would love to see some videos on how are you doing.

@jacobkollerup 4 жыл бұрын

Hi! Very glad you liked it. I’ll improve the audio for upcoming videos, since the wind noise is quite awful on this one. Congratulations with the boat and coming into sailing, you will definitely not regret it. Yes, you should absolutely be able to power your windlass from the thruster battery, just remember some thick wires and you should be good to go. There will be lots of more videos to come:)

@captmiker7423 4 жыл бұрын

Thank you. Another great video! Now that I understand what’s involved, you’re saving me a lot of money. Bow thrusters including install can cost $10,000-$12,000 in my area. Most of that is labor. Could you sand/grind the very bottom center of the compartment so the tube is bonded w/ thickened epoxy the entire length below the tube?

@jacobkollerup 4 жыл бұрын

I'm glad you liked it and found it helpful, always good to save a few bucks;). Yes, you can definitely fill the underside of the tunnel with thickened epoxy and glass over. However the installs where I've seen it done is mainly where the tunnel sits very close to the bottom and glassing all the way around would be impossible. In my install I can easily do the normal glassing around. On the Crownline I did, the filling of thickened epoxy, so it´s a matter of the individual install.

@RH-mr4hq 4 жыл бұрын

I am installing a bow thruster right now as well. What are you planning to use for fiberglassing? what type of mat/roving, laters? Epoxy? Thanks and great channel!

@jacobkollerup 4 жыл бұрын

Hi! I’ll be using west systems epoxy and biaxial 300gr (maybe 600gr on the flat surfaces). Reason for going with the epoxy is the excellent moisture barrier (on the outside). Inside because the epoxy works down to around 4 degrees C, where a polyester needs 12-15 degrees C. Also the lack of styrene fumes is also quite nice. Downside is the price! Here the price of epoxy is about 4x the price of poly. I hope to have the next video up within 2 weeks. The sound quality will be greatly improved in the next video. Thanks for watching:)

@gayetmenglik1551 Жыл бұрын

👍❤👌

@jacobkollerup Жыл бұрын

🙏🏻🤗

@Mifseafood 2 жыл бұрын

Where were you able to get that 3d printed piece? I have a 3d printer and can print that piece out. Can you send me the file by chance? Thank you!

@jacobkollerup 2 жыл бұрын

I designed it myself. Sure I can send you the stl file. Just need your email:)

@johnyalowica8423 10 ай бұрын

5:27 where did you find the scribe to mark your holes?

@jacobkollerup 10 ай бұрын

Hi, I modeled it in 3D and then 3D printed it

@johnyalowica8423 9 ай бұрын

0:26 can I buy it from you?

@johnyalowica8423 9 ай бұрын

1:26 I will be installing a bow thruster in our sailboat We bought a 1984 Scia 50!

@jacobkollerup 9 ай бұрын

I can send you the 3D file, it’s a quite simple print if you know someone who has a hobby 3D printer.

@johnyalowica8423 9 ай бұрын

@@jacobkollerup could you send me the file? That would be great!

@johnyalowica8423 9 ай бұрын

0:06 would you be able to print me one and I will pay you for it? For shipping too!

@jacobkollerup 9 ай бұрын

Let me figure out. It’s for US right? Note that it only works for the Ø125 mm tunnel

@treashurehunter800 Жыл бұрын

Your goggles clearly aren't keeping the dust out.