@kenf2662 11 ай бұрын
Could you have removed the spring adjustment bolt and remove the spring thru the hole. by looking at it again you can.
@BehindTheTrigger0 11 ай бұрын
At the moment I can not find my extra trigger. I will say that the spring will not just fall out if you remove the weight adjustment screw. The hole where the screw goes is small so it would be difficult to remove it. There may a step in the assembly to retain the spring. I will look for the spare and keep you posted when I find it. For now I pinned this comment.
@BehindTheTrigger0 10 ай бұрын
I found my spare trigger. The factory spring is a little bit bigger then the adjustment screw hole. So you have to take the trigger out to change the spring.
@kenf2662 10 ай бұрын
@BehindTheTrigger0 Thanks I will be installing the mechanical pencil spring, very little trimming.
@dennisd157 Жыл бұрын
Your video was very helpful. I installed a new spring successfully!
@bapojean5981 16 күн бұрын
For those of you that have replaced your spring. Have you any concern about the trigger being too light of pull? I just replaced mine and now it will fire by just pushing it sideways a bit. Has me concerned about it being safe.
@BehindTheTrigger0 16 күн бұрын
You might have to give it a little more sear engagement to keep it safe.
@bapojean5981 15 күн бұрын
@BehindTheTrigger0 I did adjust it a bit more and have it "fixed". Thank you.
@BehindTheTrigger0 15 күн бұрын
@@bapojean5981 You’re welcome.
@ernestomantegazza7466 2 жыл бұрын
Good review. Did you remember the OD and the lengh of original spring ?
@BehindTheTrigger0 2 жыл бұрын
The factory spring is: O.D. Is about .147. The length is about .357. These measurements are in thousands of an inch
@gordy1961 3 ай бұрын
@@BehindTheTrigger0 Don't suppose you remember the diameter of the spring wire?
@BehindTheTrigger0 3 ай бұрын
@@gordy1961 I don’t. I actually went with the YoDave spring.
@m.fleischman2150 Жыл бұрын
Good video. Thank you - it helped me a lot. That pin was a super PITA to get out but it eventually gave. What is that thing mounted on the action? Is that a light saber from old republic? Those were more civilized times.
@BehindTheTrigger0 Жыл бұрын
If you are referring to the scope it is a Weaver T36
@normkeller2405 Жыл бұрын
Any chance you can re-shoot the video to show what you are doing?
@BehindTheTrigger0 Жыл бұрын
I do have one laying around. It just may take me a moment to get to it.
@ronl384 3 ай бұрын
Aren't you supposed to remove the trigger pull screw and nut first?
@BehindTheTrigger0 3 ай бұрын
I didn’t on any of the six I did. However, the screw was already backed off all the way.
@OFFTHEBEATENPATH1977 Жыл бұрын
Thanks
@BehindTheTrigger0 Жыл бұрын
You’re welcome.
@kitsune4635 Жыл бұрын
what size punch is needed?
@BehindTheTrigger0 Жыл бұрын
Think the punch was .125in / 1/8in in diameter.
Cool Items Official
Рет қаралды 19 МЛН
Фани Хани
Рет қаралды 1,4 МЛН
MCARBO
Рет қаралды 460 М.