This video describes the basic of DALI lightning system, components used in that and a basic example of installation of DALI system.
Пікірлер: 41
@ursulanield97672 жыл бұрын
Hi Sahil, good video. So the power from the distribution board only goes to the dali control unit ? And can we have two lets say 3 gang switches to switch on and off the lights from different areas in the room, for example if the doors into the room were in opposites sides?
@Imtiyaz5power2 ай бұрын
Awesome ❤
@WorkPlace-ci6lh4 ай бұрын
The guys with this accent are constantly smart))
@hassanyousaf4241 Жыл бұрын
Can we use the same dimmable drive for fans to doing slow and fast ??
@aboodeedodo9494 Жыл бұрын
Thanks sohil , from Saudi Arabia 🌹you make this lesson easier
@sahilkumare93 Жыл бұрын
It's my pleasure
@b.mjoselin64542 жыл бұрын
really good
@azazansari1561 Жыл бұрын
sir light is not working after changing the new dali ballast ?
@dynamotexan2 жыл бұрын
how common/quickly is this method making its way into construction? on my first job using this system. seems vastly over complicated with little benefits. typically we use BAC connected controllers that handle local areas and then send status of switch legs to the central hub to monitor the facilities. this method, as i understand, sends conditions and manual override to the central hub to then cut/connect the raw electoral power to switch legs. i suppose the (relative) benefit.... in the past the individual components (switch/sensors) had built in IDs so that the installer needed the bar code for each piece to settle the network. DIAC allows to change their ID..... still cumbersome
@sahilkumare934 жыл бұрын
Somewhere in this video I mistakenly pronounced lightning which is lighting. ☹️🙏
@HaLam1163 жыл бұрын
Tks so much :) I no understand different between Basic System : 1. Motion Sensor + DALI Luminaires 2. DALI Motion Sensor + DALI Luminaires? Motion Sensor + DALI Luminaires need DALI Control then DALI Motion Sensor + DALI Luminaires NO need DALI Control?
@mohareesansari54043 жыл бұрын
But sir I do the same connection but not working can u tell me o other connection and can you tell me wire bomber 0.5or 1.5 mm wire use
@imamenon2 жыл бұрын
Is there any reference for the wire gauge to be used in DALI control systems?
@dynamotexan2 жыл бұрын
communication is 18/2 AWG. lighting is 12AWG
@eduardobungcaras75032 жыл бұрын
Nice
@mohitparjapati64394 жыл бұрын
Mast ha
@aboodeedodo9494 Жыл бұрын
One question, the ballast coneccted parallel or series
@aboodeedodo9494 Жыл бұрын
Ok you mentioned in video 🌹
@sahilkumare932 жыл бұрын
Thanks for reaching 150 subscriber 👍🙏
@kabeerahmedshaik8274 Жыл бұрын
Lighting or lightning?
@piyushkumarjha11112 жыл бұрын
do this DALI system works with KNX?
@humanmax602 жыл бұрын
Yes, you need a KNX-Dali-Gateway
@shrikant10412 жыл бұрын
Is DALI switch operate from mobile?
@shrikant10412 жыл бұрын
IS THERE IS ANY APPLICATION OR ANY OTHER THING FOR THAT?
@imamulhaque6370 Жыл бұрын
Dear sir I have 1 request I want know related for motion sensor control panel Wiring form control panel DB to motion sensor and light. should be have in side DB relay fuse contector auto hand mode option plzz make one drawing hope you understand 🙏🙏🙏
@videoforyou67298 ай бұрын
ok
@mohareesansari54043 жыл бұрын
Sir tell me please
@sahilsyed28502 ай бұрын
i want to design dali system for one of project. can you please support. i am ready to pay aslo
@sahilkumare932 ай бұрын
What help you require ?
@sahilsyed28502 ай бұрын
@@sahilkumare93 Can I have your whatsup number? I can explain
@shafi21612 жыл бұрын
So basically each light is controllable seperately in Dali system.
@sahilkumare932 жыл бұрын
Yes it can be controlled individually or in combination of lights.
@susantoprayitno48143 жыл бұрын
Bahasa indonesia
@brandonfrancis86962 жыл бұрын
Sahil, It’s a lightING not lightNING. Lightning is dangerous you cant control it.