This shows the design / assembly and use of the universal type bucket / racing seat slider base mechanism.
Пікірлер: 50
@mojmoj37637 жыл бұрын
someone show how to put them on the seat for Christ's sake
@tomw5vlt1194 жыл бұрын
Perfect timing for me, found this right away, and while some minor differences, the unit I purchased looks 95% just like that. Thank you.
@buxycat4 жыл бұрын
Thank you! Just bought a seat for PC driving sims, the seat rails had no instructions, so i didn't know which way up or which way round to put things. Should be really easy to do after seeing this, thanks again.
@timgreen65222 жыл бұрын
If you pinch these in a vice it also pinches the channel and restricts the whole thing moving. Also as many have stated here and as I have found, the pull up bar does not 'lock' in place after giving it the vice treatment but simply falls off. The bar will operate perfectly well if it is effectively too wide for the space between the runners and sprung into place after the sliders are bolted into place.
@kitatit5 ай бұрын
Thanks for the great vid. To the point and cleared up all my questions. Greatly appreciated!✊
@stephenhajovsky3971 Жыл бұрын
Thanks for making that. Very helpful but I wish you would've shown the full install. Next time:)
@marciaz314 жыл бұрын
Thank You for the video ... I had no idea in how to put it all together ..
@saw31489 Жыл бұрын
At what point do you actually install them?
@nydo3 жыл бұрын
Wow, exactly what I was looking for. Thanks!
@davidkitchens34042 жыл бұрын
highly recommend this purchase!
@L6632 жыл бұрын
Thanks for the recomendation.
@fatguyonalittlebike33368 ай бұрын
What? I’m literally more confused than ever…. The people I got it from said it bolts in the other direction… flat side to seat bracket….. also the bar facing the other way…. Why can’t I find clear instructions?
@brettsmrz90725 жыл бұрын
I have these exact same adjusters and when I put it in my vice and did this, it doesn’t lock in place. I can still pull it apart by hand. Not sure what to do?
@MrJahoot4 жыл бұрын
i have exactly the same problem. just wont lock in. might have to pull the welder out
@MrMarcusjarvey3 жыл бұрын
Am I the only here one without a massive heavy duty bench vice?
@aicram622 жыл бұрын
Rather than bolting this to the car floor, could one bolt this to a swivel plate and get the best of both worlds?
@jamessmith5905 Жыл бұрын
Could you put these under a console to make it slide?
@sparkplug964 Жыл бұрын
Sorry if this is a dum question but how is this universal because the sliders have a fixed width?
@L663 Жыл бұрын
good point !
@newmyid159711 ай бұрын
u can stretched the slider to make it wider and basically it fit to any seat and base..
@jr61363 жыл бұрын
How on earth did you get the rails to come out? I can’t seem to figure it out. I saw you out it on its side and press but I guess I am doing something wrong when I try? Mind saying briefly explaining how to do it?
@L6633 жыл бұрын
I think as long as you pull the lever so the rails can slide they will either slide out the front or the rear.
@P3ktoRis3 жыл бұрын
i tried with wd40 and it worked....just needed lots of wd40
@sovereignsoultribe2 жыл бұрын
i cant do it either... i have tried for several hours and in fact i think i have broken one of the sliders... i cannot get the slider to slide out so i can mount it... i also don't have one of those big arse vices which don't seem to work anyways going off all the comments... loosing my bloody mind... faaarrkkkkk
@jr61362 жыл бұрын
@@sovereignsoultribe i did eventually figure it out. I had to press the press that compresses against the crease of a brick wall in my backyard and apply force lol
@AlbertoGonzalez..2 ай бұрын
I haven’t been able put my seats in for 4 months this has been harder then doing both my axel’s 😡
@Dwaynesvideodump4 ай бұрын
What if the rear inside mount attaches to the tunnel not the floor?
@ranjivkalsi3253 жыл бұрын
What if you don’t have a Vice. What else can be used?
@L6633 жыл бұрын
Everybody has a vice.... girls... drink... sweets etc !
@balthazarriviere60364 жыл бұрын
My left rail is stuck and doesn't move at all.
@joesarks4 жыл бұрын
You ever figure out how to fix this?
@balthazarriviere60364 жыл бұрын
@@joesarks I did! Somehow the right rail locked in a different position. I was trying to unlock by hitting hard with a hammer but didn't work and it was a bad idea cause the edge of the rail had bend. Then I reassembled the rails with lifting bar from the seat and manual I apply force by hand on the locked rail. I apply some WD-40 before doing anything to help with friction. Hope it works for you
@joesarks4 жыл бұрын
Balthazar Rivière, thank you!!!
@glory33392 жыл бұрын
I tried to do it the way shown in this video, i put it in a vice and pressed and it didn't stay together, it fell apart, so i guess I have to do it the way shown in the following video : kzfaq.info/get/bejne/oJ6cpsRoupynkoU.html
@chopperman3316 жыл бұрын
Width once assembled?
@L6635 жыл бұрын
you csan see dimensions here images.esellerpro.com/2133/I/844/0/rails%20for%20front%20seat%20universal%20v1.jpg
@MrJimb019894 жыл бұрын
Thanks helpt
@meetmyballs7 жыл бұрын
Next video plz ;)
@-_-1529 Жыл бұрын
Good news and bad really, inow I know how to do it but I need a vice. Lol
@arqagon4 жыл бұрын
What are the dimensions ? Width and height?
@jsizzle2k63 жыл бұрын
too much talking not enough showing how..
@L6633 жыл бұрын
Well I must appolgise if i have talked too much. Its not my intention to be over verbal when making videos but sometimes the extra explanation helps people understand the process. I can however understand that this may not be to everyones taste. I will however in future try and be a little more consise so as not to upset or offend people like your good self who preffer the more direct and "less is more" approach to video narration. But thanks for watching and sharing your point of view as it is much appreciated.