No video
Detroit DD15 Fuel Injector replacement and injector code programming - misfire on multiple cylinders
Рет қаралды 10,073
Күн бұрын
@joshuasd619 Жыл бұрын
I appreciate your showing us the computer I have one just still learning on it
@alreyindustries Жыл бұрын
Thanks for the thanks 😊. Let me know if you have any questions or anything and I’ll try to help out however I can.
@edwinabarca5037 7 ай бұрын
What is the code for injector #6
@brandookie79 3 ай бұрын
Thank you. Appreciate it. I have this job tomorrow
@joshuasd619 Жыл бұрын
Thanks!
@vladbex Жыл бұрын
What kind of app are u using for laptop ?
@alreyindustries Жыл бұрын
Detroit diagnostic link
@cristiantoma9386 7 ай бұрын
Hi, nice quick video ! I have a DD15 with SPN 3659 FMI 5 injector cylinder #1 spill control valve ("amplifier"), circuit open. What does ISC% stands for? Your values are reading 0, mines are -5,-6,-5,0,5,11. Also Injector Code returned values are invalid "??????" for all 6 injectors. I have changed the injector harness, problem still on. Any advice?
@alreyindustries 7 ай бұрын
Did you replace the injectors?
@cristiantoma9386 7 ай бұрын
@@alreyindustries I'm pressing the READ option first and Injector Code returned values are invalid "??????" for all 6 injectors. Tried on a different truck with no injector fault codes, the Injector Codes are showing. Should I proceed with replacing injector#1. Will then the reading values will be correct after ?
@VitaliyKhomich 2 жыл бұрын
You are wrong. Injectors need to be torqued down to 15 pounds then you add 90ﾟ turn
@alreyindustries 2 жыл бұрын
😳 Well, I would recommend everyone look up the torque specs for their specific engine in the manual. Perhaps I am wrong. I have not had any problems with the injectors I’ve done, but thanks for the input. 👍
@obrizzle375 2 жыл бұрын
@@alreyindustries sorry but your injector torque is wrong. Its 15 ft lbs and then 90 degrees. This is the issue with ppl making youtube vids and giving out correct info
@alreyindustries 2 жыл бұрын
@@obrizzle375 it’s been a while since I made the video, but I’m pretty sure I went from the manual. If you read the above response someone already “corrected” me and I said I’m sorry if I’m wrong, but everyone should go by the manual not by my video for specs. If you want to make a video with correct specs go ahead, but don’t be overly critical.
@joshuasd619 Жыл бұрын
Why would there be torque specification then if your just going to ignore them and tighten till you think it’s right
@VitaliyKhomich Жыл бұрын
@@joshuasd619 That's the exact specifications and directions from the freightliner
@edwinabarca5037 7 ай бұрын
What is the code for injector#6
@pedroromero5918 Жыл бұрын
What if just one injector was changed would I need to get the codes off all of them?
@alreyindustries Жыл бұрын
No. Just the one you are changing
@likatrucking9443 Жыл бұрын
Do you know how much cost to do cylinder misfire 1&3
@alreyindustries Жыл бұрын
What do you mean?
@likatrucking9443 Жыл бұрын
@@alreyindustries I was wondering what is the labor replacing of 1&3 misfire DD15 Detroit Cascadia 2019
@timothymcclure239 9 ай бұрын
I'm reading 15 ft/lbs + 90° on the injector hold down.
@tsmjs4 6 ай бұрын
Me too.... is this correct???
Idle & Emission Solutions
Рет қаралды 13 М.
Pedro Fuentes
Рет қаралды 10 М.
Pedro Fuentes
Рет қаралды 104 М.
Francisco Amaya
Рет қаралды 16 М.
Francisco Amaya
Рет қаралды 10 М.
DETROIT REBUILD SPECIALIST
Рет қаралды 109 М.