Wish I could of seen the screen better but great info man
@johncasey2398 Жыл бұрын
Does the software require you to be logged in to compare data with the server or will it still work offline
@vicdangcАй бұрын
hi, great info, do you know how to change in the new mcm, vin and esn?
@alreyindustriesАй бұрын
@@vicdangc I think in the actions tab at the top you can “sync” the vin and/esn
@kordelewaters26552 жыл бұрын
Scrolling through your vids and seeing the tablet. 95% sure your likely a lead Penske tech. Reasons from the tablet, and info on all major engines and apu stuff even. Am I wrong?
@acv2634 Жыл бұрын
Trying to establish CAN network between Woodward Easygen 3500XT and DDEC 4. Please help
@bilelkhodja2899 Жыл бұрын
Hi sir i did get a coronado dd16 600hp engine with 18 speed trans 3.73 ratio and 24.5 wheel original from dealer i use to get 1500 rpm at 70 mph i use this truck for havy loads and was perfect and now i switch to dryvan 80000 lb wish i dont need all this power what i did is change the wheels to 22.5 low pro and the truck become 1500rpm at 65mph i did change the ratio from 3.71 to 3.21 and now get perfect speed at 1500rpm at 74 mph but now i notis that the engine eat more feul and i was thinking if anything i can do 7 program that lower hors power or anything to 7 better feul mile pleas wait for your answer
@Adoken1012 жыл бұрын
Can you retrofit another module to this truck by change it's vin and serial. thx. just newbies.
@alreyindustries2 жыл бұрын
As long as it is the same part number. Like if you were to have the same module from a different truck that is the same you could, but not if it is a different part number. As far as I know.
@adamhose5231 Жыл бұрын
Is this the Detroit diagnostic link and can you adjust the cruise control coasting and engine brake engagement speeds? For example I bought a 2019 Freightliner dd15 without the radar on the bumper or windshield but it has a parameter set so when I set the cruise control at say 65 mph it will Coast it down to 60 mph and then engages and goes back up to 65 mph. And then the engine brake doesn't come on until 5 mph over the Cruise speed setting. Is there a way to adjust that?
@alreyindustries Жыл бұрын
Yes it is Detroit diagnostic link and yes you should be able to adjust those parameters. However if you engine computers are password protected you’ll need the passwords to change speed settings and a few others
@BobirJon36911 ай бұрын
I have the same issue on my 2020 cascadia
@ajrandhawa39475 ай бұрын
Can I have your contact info and where do you have the shop ? I need something to look into my truck .!
@alreyindustries5 ай бұрын
Sorry I don’t have a shop or that software anymore.
@bz4shez Жыл бұрын
Hello I have a 2017 dd15 and I have some questions about cpc and mcm parameters in programming. Do you have a way I can contact you?
@alreyindustries Жыл бұрын
What’s your question? Can I answer it here?
@zeke11500ify Жыл бұрын
I keep having the same code pop on every 400 miles 3058 9 and sometimes 10 I done change every sensor that’s required to change for that code new delta pressure pipe sensor somebody please help
@alreyindustries Жыл бұрын
static.nhtsa.gov/odi/tsbs/2016/MC-10199616-9999.pdf Have you checked the two ports at the delta p sensor?
@allday3433 Жыл бұрын
Does it need to be online or is this working offline? To compare perimeter
@alreyindustries Жыл бұрын
If you have to connect to the server, you have to be online.
@enrique1765 Жыл бұрын
What do I use to plug this into the truck?
@alreyindustries Жыл бұрын
Do you mean what do you use to connect your computer with the detroit software on it to your truck? If that is what you’re asking, normally I would use the nexiq usb link. It is a little blue box that has one cord that connects to your computer and another cord that connects to your truck.