I wish I would have seen this sooner, might have saved me a few hours of frustration. I can’t thank you enough. FYI for others, my pin wasn’t stuck but taking it apart and reassembling it seemed to do the trick.

Whoa! This fixed my machine 😂 I was pulling into Home Depot to get it serviced. I saw this video and thought why not try it. And boom it’s fixed!!!!! You’re the man!!!!

Dude, it's been sitting for 3 years and your vidio is up for 6. You the man!!

Thank you!!!! You saved me hours of time, and possibly the expense of buying a new power washer.

I can use this. I also liked it when your dog stepped in for a nod.

Thank you so much! I didn't even take it apart. After watching this I just sprayed it with WD-40 then tapped it with a hammer and whala making pressure! Thank you!

Having this exact issue. Great video. Good close up on what you were doing. Easy to follow. I wish all KZfaq fixit tutorials were like this

Thank you SO MUCH-fixed me right up. Laughing because my husband threw up his hands, but via your video instructions I got it going again!

5 min fix but have to watch 10 min video. Now a fifteen minute fix 😂. But anyway jokes aside, thanks worked a charm 👍

Super helpful, this solved my "no pressure" problem on 3600 psi DeWalt, I didn't have to remove the pin, just tap it to loosen and worked great again. Thanks!

7 year old video, and it just saved me. Thank you!

I have a 3425 Dewalt Pressure washer about 3 years old this spring season. Started right up but no pressure. After checking user serviceable items I found your video, followed the directions and I'm back in business. Although I winterize my unit every year and it's garage stored I still encountered this issue. Thanks for the video.

Thank you so much. I was so frustrated and now it’s up and running again. You’re a life saver

I have a 3400 Dewalt bought it last year used it once tried starting yesterday it would run for a min and backfire. i took carb all apart checked jet it was clean. Did a youtube search found you. Mine was just the opposite, factory setting screwed down to tight over pressuring pump & motor, took valve apart it was operating fine. left adjustment about where yours was, ran fine....thanks for taking the time

Thank you!! I hope this fixes my lack of pressure. Love your dog. From NE WA.

dude, this worked. Awesome, took me about seven minutes, and I have full pressure again! I did exactly what you told me to do! I knew some wise person on KZfaq would have the answer!

Excellent, such an easy fix and less than five minutes. Thank you!

I was ready to junk mine until I saw your video. Works great. 10 minutes to find the tools and 5 minutes to fix. Thank you

Thank you! This totally fixed our Dewalt 3000 psi pressure washer. Exact problem. Keep it up!

Thank you so much. I was about to pay to fix mine, and your video fixed it right up!

Thanks 🙏🏽 brothers saved me some money blessings to you an your loved ones

Not all heroes wear capes. Thanks for the video sir! Glad I stumbled upon it. Now I know what to do just in case. I got the 3300psi

So glad I watched, can't wait to try it.

Thank you SOOOOOO much ….I have a Dwalt 3400 PSI , only used it may be 7-8 times, and today I got ready to power wash my side walk and driveway, it had no pressure, I am so glad I went online and after watching 4 videos, yours was the most relevant one that gave me the answer and it saved me at least $180 (according to the repair shop) , thank you so much again, you are a great blessing.

Did the same and works great. Thank you sir you are a life saver ❤. God bless you

Thank you for posting this video! I was about to buy a new $275 pump. This was the fox for my pump problem!!

Hey man a big thank you from down here in New Zealand. I thought my fairly new waterblaster had crapped out completely which was a real inconvenience at this time of the year. (its summer here). But i had a look on you tube for a repair and found your video and for the first time ever it all worked exactly as you said. Was an easy fix and its going fine. Thanks for your effort.

OMG, I'm watching this with the audio off, but your Dewalt looks like it has the same pump as my SIMPSON, and now I know EXACTLY how to get at my unloader! You rock.

I really appreciate the video. My 3200 quit having pressure yesterday and I about lost my mind, since it was practically brand new. Was afraid it could have been something expensive.

Thanks you just saved me time and money, took me about 10 minutes and it’s fixed 👍

Thank you so much! Just got a pressure washer for $200 because buddy said the pump was not working . Free fix! Pressure washer at 20% the price!

thank you friend , I have a back & decker 2600psi had the same problem !!! hugs from Brazil

Thank you for this video! Just saved me $395 from repairman claiming I needed a whole new pump!

Excellent video. Just finished the fix on my Dewalt 3400 PSI pressure washer.

This is a great post!! This is the second year we had to watch your video and fix the pressure washer again. Worked out great!! thank you so much!!

Fixed my water flow issue right up. FYI the small nut on the stem is a 10mm and the big nut is a 7/8. Thank you much for your video

This is exactly what my problem was. Thanks for the help!!!!

Great video. Was about to take to the shop when I decided to check ole KZfaq. Low and behold you were dead on right! Saved me money! Thanks

Thank you for sharing your videos and knowledge. Fix mine I was going to send it out.

Great video, thanks for the help! Worked like a charm!

great video. I've used it each of the past 3 years!

Very helpful! I'm having pressure issues and I can't figure out why. Now I know! Gonna fix it right now! 👍🏾

Great video brother. Perfect fix!! Worked like a charm on my DeWalt 3400! 🤙🏼🤙🏼

Thank you Billy I'm going to check my pressure washer out now

Thanks. It got my pressure washer working again.

Great job, I'll be trying this tomorrow!

nice vid bud ...i fixed 2 pressure washers after seeing this ...thankyou

Thank you very much sir I fix my own pressure washer because you did a good video

Thanks, Billy! Gettin' My pressure washer adjusted to get to work. You da Man! :-)

Thx for the tip I appreciate it I’ll try check that on my pressure machine

Thanks dude! I'm back to work.

Boom! You saved another. Thank you.

Worked great. Saved me time and money.

Thanks for your great video Bill, I will fix the same problem that you have showing on the video.

Awesome video! Worked on my 3600 dewalt pressure washer also!

Thank you. This was exactly the problem

Thank you ,for the video ,now I know how to fix mine 👍🏻👍🏻👏🏻

Life saver!! Thank you!

Thank's I have the same Pressure washer worked great

Thank you very much man!!!!! You just saved me a ton of money!!!

only watched the first half of the video lol but thank you bout to give this a try cheers

Thank you for that video! That was the problem!

Thank you sir thank you very much had it at work and same problem bit the other guy I work with is a fake mechanic. Went bought brand-new one cause said it s broken but it's not anymore thank you again

Thank you this is exactly what was wrong with mine Thing is brand new with only like 10hrs run time

Gotta love KZfaq! Thanks. Great solution.

Thank you! You solved our problem!!

Me and my husband started our own business and this video really help us at 2 am 🕑 😅 and you saves us a headache 🤕 thank you for your time

Thank you, Billy!😀👍

Mine is no pressure out of the box. I either have to wrench on it brand new or I need to get the gas out of it to return, think I will leave the oil in it.

Great job. Going to try it and if it works I'll let you know. This video is about 6yr old and so is my washer. Thanks Billy.

Your the Man I appreciate the video it saved me a lot of Money

Thanks a million...kind did the same thing !

This worked. Thank you!!!!

Dewalt 3400 PSI ... His solution work perfectly!

I have the Dewalt ( Simpson ) 4400, The other thing to check is the valves, they crack after a while, I've done 100s of homes, a 25,558 sq ft Beach front hotel in 6 hours and have a 75,000+ sq ft hotel lined up with my Dewalt 4400, it lost pressure but my problem was the center valve, the plastic housing that holds everything inside cracked. It was hard to notice. Easy $70.00 fix in 10 minutes.

thank you so much, i fix mine 👍

Thx for sharing!

It works greats and easy to do. Thank you

Thank you 🙏 sir for your video you save me a few dollars.

Thanks fixed mine

Thanks it worked !!! Awesome ..

Very good teacher

This fixed it. Thanks

Thank You 🙏🏼 you saved my day 🤝🏻

Thank you so much. It worked.

My DeWalt has absolutely no pressure and it's been driving me crazy the same scenario I haven't used it in a while so maybe it's the same problem nice video thanks for the help

My dude! Thanks!

Would this be a good application for anti-seize on that valve? Thanks for the video!

thank you very much, I was planning to took it the the repair chop, now I'm gonna try before,,,,,

Great fix.

You da man! It worked for me!

Helped me today

UPDATE:1 year and still cranks within the first 2-3 pulls. Probably will buy another when this one finally does bite the dust kzfaq.infoUgkx43QMbQqu67IZadu9ou8Sg1BdrunMRNqX . No issues at all. Very happy with it.UPDATE: After 6 months of use and over 70 uses I would still highly recommend this pressure washer. It does vibrate a decent amount but never had it “walk” like others have mentioned. No oil leaks, still seems to run like the day I bought it. Still cranks within 2-3 pulls every time. Very happy with my purchase!Have used it about a dozen times now. Plenty of power, cranks up on 1-2 pulls every time. My only complaint would be I wish it was a little taller to make it easier to walk with it (hits my ankles a lot) and that the two hose connections were a little further apart but it hasn’t caused me any issues. Seems to run a good 1-1/2-2 hrs on a full tank, overall a well built machine and definitely worth the money in my opinion.

Thanks 🙏 men it works

Great!!! Thank you👍🏻

Thanks for getting right to the point and showing the KZfaq community a quick easy solution. Oh, and not asking me to smash/pound/crush the like button.

Thank you!

Good job thank you

Thank you, thank you, thank you..........god bless you.👍👍👍👍

Gracias my men 👍