Did I Install My Outlets WRONG? // DIY Workshop Build

Рет қаралды 21,245

Күн бұрын

🔗 Samcraft Website: samcraft.shop/ 🔗 Full Workshop Build Playlist: • 20x32 Workshop Build ⬇️ MORE LINKS BELOW ⬇️
🔷 OTHER LINKS 🔷
🔗 WAGO Lever Lock Wire Nuts: amzn.to/3TOc61S
🔗 WAGO Inline Connectors: amzn.to/4aRLoLM
🔗 Leviton Outlets: www.homedepot.com/p/Leviton-1...
🔗 Thermostat - Honeywell CT410B: amzn.to/3HeQlAG
🔗 Electrician's Screwdriver: amzn.to/48sSvZq
🔗 Romex Wire Stripper: amzn.to/4aVhI0f
🔗 Recessed LED Lights: amzn.to/3H5ORJ9
🔗 Sili Gun Caulk Gun: amzn.to/4b2tMgv
🔗 RevolutionPly: www.lowes.com/pd/RevolutionPl...
🔗 Oscillating Cutting Tool: amzn.to/48jti3y
🔗 Cordless Finish Nailer: amzn.to/3S5gXdK
🔗 RockRipper T Squre: amzn.to/3S5gCb0
🔗 Little Giant Step Ladder: amzn.to/3S6dNGq
🔗 Worx Circular Saw: amzn.to/3NOhfmE
🔗 Hammer Style Stapler - Arrow HT50: amzn.to/3TspqZz
🔗 Rolling Scaffold: amzn.to/3RfsyGF
🔗 Spinning Wire Spool: amzn.to/3vixWQZ
🔗 Wire Staples: amzn.to/3RZwGuL & amzn.to/48dpzVm
🔗 Flashing Tape: amzn.to/48ummQL
🔗 Lexel Sealant: amzn.to/3GRH5m1
🔗 Forklift Safety Cage: amzn.to/3Nqoz7N
🔗 Sam's Tool Belt Rig: amzn.to/3tohai7
🔗 Paslode Cordless Framing Nailer: amzn.to/46U10fr
🔗 Workpro Clamps: amzn.to/46w5SWT
🔗 Craftsman Cordless Circular Saw: amzn.to/3FSK7Wy
🔗 Craftsman Cordless Impact Driver: amzn.to/3u8MCl7
🔗 Craftsman Cordless Miter Saw: amzn.to/47iaBwf
🔗 Sam's Hat: amzn.to/3UHbXvA
🔗 Laser Level & Detector: amzn.to/3QgypuI
🔷 OTHER VIDEOS 🔷
🔗 All My Laser Engraving Videos: • Laser Engraving Business
🔗 Our Family's Small Business: greenacrehomestead.com
🔷 ABOUT SAMCRAFT 🔷
Samcraft is a channel all about educating, inspiring, motivating, encouraging, and sharing the things I've learned since starting my own small business in 2018.
In today's video I install my finish electrical work. I install the electrical outlets, wall plate covers, light switches and switch covers. I also wire up my sub panel breaker box and add some inline thermostats for my electric heaters.
🔷 VIDEO CHAPTERS 🔷
#samcraft #workshopbuild #shopbuild
*DISCLAIMER*
This video and description contains affiliate links, which means that if you click on one of the product links, I’ll receive a small commission. This helps support the channel and allows us to continue making videos like this. Thank you for the support!

Пікірлер: 212

@gotbacon04 5 ай бұрын

Been doing electrical over 30 years. You can use the oscillating tool to trim the front of the box flush. I have had to do that when wall coverings changed. As for the receptacles I always tell people I put it then that way so the electricity will not fall out. 😂. Very nice shop. Keep up the great work.

@Samcraftcom 5 ай бұрын

Brilliant!! I really appreciate you sharing this REAL Pro Tip!!

@pgogel8974 5 ай бұрын

Buy a cheap oscillating tool from harbor freight and trim your boxes tight to wall.

@JCsBoardShackTX 5 ай бұрын

Beat me to it. Trim it. Just fine

@joethanks3745 5 ай бұрын

@pgogel8974 I bought a cheap oscillating tool from harbor freight 7 years ago I use it all the time I'm glad I saved about $100.00

@MattMadeIt123 5 ай бұрын

Former electrician here. In residential construction, an upside-down outlet indicates a half-hot outlet. Meaning 1 side is constant hot, 1 is switched. Another time to install the outlet upside-down is if the plate covers are metal. Usually in commercial/industrial work. The idea being if the cover comes loose and falls off with something plugged in, the metal cover will fall onto the ground post and not across the hot and neutral. But hey, it's your shop. Do your thing. BTW-The panel looks fantastic. Better than many "pro" jobs I've seen. If you did need more circuits you could always get thin mount breakers or quads for the 240V locations.

@gary-gilbert 5 ай бұрын

Use one of those fancy lasers and cut out a decorative trim piece to put behind those outlet plates

@karencary3312 5 ай бұрын

I thought the same thing. Be sure to show us, Sam.

@edhibbard2348 5 ай бұрын

Or try goof plates

@feelingtardy 5 ай бұрын

@@edhibbard2348 lol, i would've caulked it

@laserengravingwithmatt 5 ай бұрын

That’s a great idea

@kelleysimonds5945 5 ай бұрын

I was just about to make the same suggestion.

@kylehobie16 5 ай бұрын

Some folks, myself included, would pig tail from the romex run to the receptacle rather than running the outlet in-line in the circuit. Obviously, what you've done is sufficient and should work just fine.

@DK-bs1xo 5 ай бұрын

Use your multi tool and trim them down. Also sub panels should have the green bonding screw removed.

@ronwhited1224 5 ай бұрын

As a guy who was shocked pretty badly many years ago, I am terrified of electrical work. I always appreciate DIY'ers who can tackle these jobs. Great work Sam.

@rickklemenz6419 5 ай бұрын

The ground on high on the high side of the receptacle when you put the receptacle in is actually the correct way for the receptacle to sit also on a stab in on the back if you have a 12 amp wire, and you want to try to stab in the back on a 15 amp plug. It is not allowed and most almost every inspector will tell you to change it but you can use it a regularreceptacle if you put your wires around the screw terminals

@davidhelfrich7150 5 ай бұрын

Place a nicely finished frame of paint stick stirrers to fill that gap.

@FowlerFamilyFarm 5 ай бұрын

Great work Sam. I did my own electric as well and the only thing I did different is in the first receptacle you wired up in the video I would have done blacks together and whites together and then pigtailed to one screw. Only reason is if a receptacle fails it will not allow power to the rest of the circuit down from the failure this way you no wheee your failed outlet is. I think I explained that right. But I’m like you not a pro at all

@verdajanefrench6692 5 ай бұрын

You could get weather stripping foam & put it around the plug boxs,behind the covers. It will help keep the cold air coming in around the boxs.

@jhinnant58 5 ай бұрын

Code doesn't specify, but I've seen where OSHA has made companies change them to ground down for two reasons: 1. It's easier to accidentally break the ground connector off if it's up. 2. Most AC -DC adapters with ground need it ground down. We always spec ground down on building plans.

@aussiegolddogcnc3d412 5 ай бұрын

Coming alive now. Getting closer. You’re doing great. Cheers. 😊

@BinaryDisastr 3 ай бұрын

As for right side up or to some, upside down, orienting receptacles with the ground up is the best way to install them. Why you ask? Because if a tool, paper clip etc is ever dropped and a plug isn’t quite in it’ll hit the ground and typically just keep falling. If it was the other way around it could fall and stay there shorting across the hot and common wire. Either way it could trip the breaker but you’re less likely try grabbing whatever it is before the breaker trips. This is how it was explained to me on a commercial job by an electrician.

@beanieweenie9543 5 ай бұрын

Sam trim the fronts of the boxes off with multi/oscillating tool. Had to do it once when I miss judged the thickness of tile backer and tile. Worked like a charm.

@dawn5227 5 ай бұрын

Cut out a little border trim piece so to build out the wall to the socket level. It will solve the asthetic problem

@PaulGriffith 5 ай бұрын

Make a wood bezel to go around the outlet box, about a 1/4 inch past the outlet cover. I like ground down when used for extension cords because of how i grip the plug, thumb on the flat and the index finger around the ground side.

@barryedwards1336 5 ай бұрын

Hi sam Barry from the UK here, I know the UK regulation standard's and wiring are different from the US, bur for your problem where you used paneling, can you make your own packing plate in wood or plastic, to go behind your covers, using your different cover plates as a template to keep the size the same, also here in the UK the power outlets are very different, nearley always they have switch's on them so you can disconnect the power to any appliance by simply turning the switch to off as the cover and switch are all one unit, we can get them without switches also, plus our switches you put them down for on and up for off, this includes light switches as well, our 13amp plugs are well known for being probably the safest plug in the world, look them up to see their features.

@blazegbs 5 ай бұрын

Nothing in the NEC book states Ground Up or Down for duplexes. Just be consistent. I was trained to put the ground down in case the ground wire comes loose.

@yellowhammerwoodcrafts 5 ай бұрын

Take some walnut and cut it in small 1/4” strips and build a frame around your boxes and then put your outlet cover plates on. It will fix the issue and look cool.

@75keg75 3 ай бұрын

2:25 print some 3d printed shims that are the same as the covers. If you use petg you could vapor smooth to get a smooth texture as the faceplate. You could potential colour code them to 20amp and 15amp etc.

@kermitfrog8340 5 ай бұрын

Ground down is the only way that works with the 90 degree plugs found on many appliances so is recomended orientation by those manufacturers. Ground up is often used to indicate that an outlet or couple outlets are on a switch in residential situations. I worked six years in healthcare and government facilities going around testing every outlet with equipment and special computer program. If any were oriented ground up it would be an automatic fail and there would be delays because a qualified electrician would have to come back in and make all repairs or changes needed then they would have to rearange for plugs to be tested a second time.

@chrisdarrow1738 5 ай бұрын

Beautiful wiring job on that panel. Made this grown man almost shed a tear...

@onedadsbattle 5 ай бұрын

You can trim the plastic boxes down to be flush with the wall board. I typically use my Oscillating/vibrate saw. Cannot do this with all boxes but yours have the two screw holes that go all the way to the back of the box.

@user-bw4qb4pg5q 5 ай бұрын

Hi Sam. those of us that can, DO, those who can't think it's their job to teach us who can and do how we should do. They are legless and they teach running. Keep up the great work.

@retiredlife848 5 ай бұрын

you could use a Dremel tool with a cutting disc and cut the boxes flush.

@TheFalconJetDriver 5 ай бұрын

Nope! Bad idea! he would cut the holes down that hold the receptacle screws, this would cause the screws to bottom out before the receptacle was tight against the box.🤯🛫 😊

@retiredlife848 5 ай бұрын

I've done it myself, No problem with shorter screws. They can be cut also if you don't have shorter ones@@TheFalconJetDriver

@wadetyler5056 5 ай бұрын

Actually, you could get the outlet insulators to put behind those plates, that would take up that space and help prevent drafts.

@tiggercares 5 ай бұрын

Hey Sam if you have any paneling scraps left over you could make little frames around them which would bring them out more.

@Tripring2000 5 ай бұрын

Sam, my only critique is the fact you did not make pigtails up in the middle circuits for the receptacles. You should never depend on a device to continue a circuit. Best practice is to make up a pigtail and have each individual receptacle connected that way, if for some reason the device gets damaged, you do not lose continuity throughout the rest of the circuit. As far as the grounding pin being up or down it is just an aesthetic decision .I was an electrician in a hospital and we were required to install the grounding pins downward. Keep up the great work and I know you’ll enjoy the new shop.

@laserengravingwithmatt 5 ай бұрын

That is looking mighty nice. Can’t wait to see your layout.

@lorenmeyer5290 5 ай бұрын

Very nice job Sam!

@rayoliver7120 5 ай бұрын

Theoretically it don't matter, what matters is you got the wires in the proper location on receptacles..... I'm 3rd generation electrician, started out as a summer helper with the union , although I choose a different Ave cause u grew up , my first receptacle I changed out HOT was 8 yrs old with my dad's supervision watching over me , so I'd say your ok... there is a difference in commercial and residential... I've done both a lot in ghe Houston area , being a licensed electrician has its perks ..... your doing good 👍

@tamistone7344 5 ай бұрын

Great job Sam installing the outlets and box!!!😊

@connieverbeck1110 5 ай бұрын

Awesome!!

@lorenrickey5481 5 ай бұрын

Easy to fix. Happens more than you know. Use an oscillating tool and cut the boxes flush with the wallboard. You will still be able to mount your receptacles normally.

@Samcraftcom 5 ай бұрын

Cool, thanks!!

@ronniemichael8832 5 ай бұрын

Put a wood spacer about 1/2" around each outlet bevel the edges so they taper in and it will have a real nice look , and that's my suggestion. I enjoy your videos keep up the good work,

@deannaoverstreet4146 5 ай бұрын

Thanks Sam! Getting close to move in! So excited for you and Angela!

@mikepetitt9624 5 ай бұрын

Sweet! Its amazing how fast you are getting this done! It looks sooo good!

@Samcraftcom 5 ай бұрын

Thank you!! 😊

@MICHAEL-lb1si 5 ай бұрын

I CAN'T JUSTIFY ANY REASON TO INSTAL OUTLETS UPSIDE DOWN. I THINK THEY LOOK OUT OF PLACE THAT WAY. BUT I LOVE THE IDEA TO TRIM THE BOX BACK . NICE JOB IN THE PANEL , AND GOOD IDEA HAVING LABLES UNDER COVER. THANKS.

@magnusltd 5 ай бұрын

Nice job Sam. Looks better than many 'professional' jobs I've seen. Excellent!

@heffe2001 5 ай бұрын

Just a FYI if you're not aware, they DO make deeper plates for just this exact issue with the electrical.

@leviteapparel 5 ай бұрын

That was an amazing video. You outdid yourself again, and your skill perceived you💯🔥🔥🔥🔥

@Samcraftcom 5 ай бұрын

I appreciate that!

@N5XHIworkshop 5 ай бұрын

A laser and some 1/4 plywood would work well to make a filler plate. A rectangle plate with laser engraved information on what tool is plugged into that fixture could be a fun add-on. You could patent it as "single gang new work box trim art."...😂lol

@everyoneknowsjeff 5 ай бұрын

I've been told that installing the outlets, the orientation you did (upside down), has a additional benifit that I would not have thought of. The reasoning I was given, from a local electrician, was that it is safer due to the ground being up if something was to drop into or touch while pluging in or out and it not hitting a hot wire. Take that with a grain of salf and to each his own. But it does make some sense. I am enjoying seeing your build out and have learned a few good tricks. THANKS

@quarlow1215 5 ай бұрын

I did the same thing on the last build I did. So i cut out some 1/4" plywood plates to fit over the box then held them on with the cover plates. Later before painting wd caulked around those which held the in place and once painted you could barely see them. I cut mine by hand with a jigsaw but if you have a laser that will cut it its easy peasy.

@donbarr9487 5 ай бұрын

Nice video! As many have mentioned, you could make outlet cover spacer-plates out of wood using your LASER cutter. If you do so consider also engraving the panel/circuit breaker number that serves the outlet on the spacer. This is very handy for troubleshooting, expanding your lab, or locking out equipment.

@emilasmith4279 5 ай бұрын

As a former IT person I’m loving the very neat and labeled wiring in that box. I remember you doing the same when working on wiring in the house. 🙌 Question is: are you as ocd as me that alllllllll the groves in the screws on the outlet covers have to perfectly horizontal??!!!! 😳😳😳🤓

@Samcraftcom 5 ай бұрын

I'm former IT too! Anytime I wire a panel like this I have flashbacks of patch panels, punchdowns, and the good ole Fluke meter chasing stranded pairs. :D I want to be OCD over the screw heads, but they always seem to fight me.

@oldguy70 5 ай бұрын

Code 406.6 states that the cover must seat against the mounting surface. So , as many have suggested, make a trim piece to fill the gap. The code does not specify which way to mount the outlet - ground up or ground down are both legal. A great video as usual.

@Realstuffadventures 5 ай бұрын

You are amazing Sam, we have been watching your channel for quite a while and you have done a great job tackling everything. This workshop build has been amazing to watch, especially how you have learned so much to be able to Get'r Done working mostly by yourself.

@bobbennett7195 5 ай бұрын

You have come a long way , Good for you. Just about done just have some details to finish it up. Have fun.

@oldmanintheshopbuiltnotbou8726 5 ай бұрын

sam take your buzz saw and cut the nails on the stud side of your outlet boxes reset them and drywall screw the box back in or you could cut you out some medallion type things to square up the outlets i wired houses for 35 years in eastern nc and all our outlets went in ground up

@XPFTP 5 ай бұрын

use a piece of lam an make backing plates for the outlets. paint them up almost be gone. look better then the outlets just hangin

@brendahogue5487 5 ай бұрын

Love your videos and enjoy watching them. May the lord bless and protect you and your family

@almachapman5409 5 ай бұрын

Good job Sam you explain it 👍good

@rickklemenz6419 5 ай бұрын

Also, that panel is one of the most professional looking panels I have seen that is how I used to wire my panels, including the little jackets, telling what the wire is coming from very very good job

@wardgross2031 5 ай бұрын

I thought it was kinda wonky until I got it. Klein Tools Rapi-Driv Screwdriver 67100. If you are doing electrical this this is sooooo handy. I love seeing the progress. Keep it up!

@pathann4195 5 ай бұрын

Just use your lasers to make washer-style spacers to go under the plate get around the box to make A flush fit will just make for a unique look

@edwinvalle4444 5 ай бұрын

Home Depot has some outlets covers which have a fat lip for this purpose when the outlet sticks out

@onsapplikasies8620 5 ай бұрын

Nice one Sam.

@Old_Man_Pete 5 ай бұрын

Very professional looking job Sam 👍, as for the outlets you could always CNC or Laser cut some fancy frames and put your Logo on them, making it truly a custom build.

@user-hi2oi1yh6q 5 ай бұрын

You can buy stacked breaker or piggy back breakers. It allows 2 ckts on the same breaker slot in the panel, if u ran out of space in panel

@alvinlindsey7432 5 ай бұрын

I am an industrial electrician according to the NEC you did it right it's the not so smart people that do not know the reason for putting the ground up.

@tracyash4246 5 ай бұрын

Hey Sam!! With your laser engraver i am sure you could make some decorative plates to fill in the gap behind your electric outlet covers.

@Damon_Barber 5 ай бұрын

Installing outlets with the ground up is better for the cord. Gravity is constantly pulling the cord toward the floor. If it sags with ground on the bottom, you have potential for the hot or neutral to arc as they pull out of the plug. With ground up, the ground has the highest chance of backing out of the plug. With zero current flowing through the ground, this is the safer option. If you ever wanted to, you could add a decorative trim around your shop at outlet height to fill those gaps. In the meantime, that gap is aesthetic.

@Damon_Barber 5 ай бұрын

To straighten the outlet, you can also stick a trim screwdriver in the ground hole near the middle of the outlet and use the screwdriver as a lever to move the outlet back and forth until straight.

@Messymy 5 ай бұрын

Have plugs that side load and that is not so good for cords. Contractors who wired addition a few years back did outlets your way and I don't like them. Have also heard some do those upside downs if the outlet is switch controlled.

@Damon_Barber 5 ай бұрын

@@Messymy what do you mean by side load? Electricity doesn’t care which end is up. As long as connections are tight to keep arcing from occurring, it’s really just a matter of preference. The exception being outlets mounted sideways on a backsplash where water has potential to rise…. Then you gotta think, do I not want water to hit the hot so mount hot side up? Or do I want it to short out as soon as possible and kill the power instead of letting the water rise higher before it trips the breaker and mount it hot side down? But even that scenario is a stretch as most cases you’re not going to have liquid that high unless the house floods… in which case main power is likely (hopefully) already tripped/lost.

@Damon_Barber 5 ай бұрын

@@Messymy if by side load you mean the outlets are sideways, then I agree. I don’t care for these as it exerts forces on the prongs in a sideways direction and over time could bend them.

@jimmcallister8487 5 ай бұрын

I think probably what triggers me, and most people is we’re just not used to them being upside down there is no right or wrong answer but as far as people doing research if you go to the manufacturers website which it doesn’t really matter what brand just google Leviton for example, you don’t even have to go to their site just Google them and click on images you will see 99% of their images are the opposite way from Sam’s devices most have writing on them they’re even packaged the opposite direction but at the end of the day there’s no right or wrong whatever you like.

@gigidygigidy6078 5 ай бұрын

You can also use that 240 for a welder now that you have some farm equipment that might need some repair. Or doing any fabrication.

@daviddarnell8898 5 ай бұрын

2023 code. If your instructions that came with the outlet specifically says (not just a picture) ground up or down that is how it must be installed. Otherwise the code does not care. Now in some counties (yes, code is usually decided by the county) in commercial or hospital settings grounds are up or down depending, usually according to use. In some areas in residential installations ground down is normal and the ground up means the outlet is on a switch. So if your instructions say ground up you have installed according to code. If they don't say then up, down, left or right are all fine according to the 2023 code book which I doubt anyone has adopted, yet. 😊

@photosbywalt7124 5 ай бұрын

Design and 3D print new covers or design a back transition plate for the current covers.

@davidwilken3584 5 ай бұрын

My question would be that as you put up your wallboard and noticed this issue, why didn’t you just reset the boxes? What you can do is make some wood extensions to cover this error. Looking good so far. 😊

@fillg 5 ай бұрын

If only he knew someone with a workshop full of tools who could create such a spacer or extension 😛 If anyone can do it Sam can.

@AlexSwavely 5 ай бұрын

@2:00 you can find deep bezel wall plates at the big box hardware stores (for about the same price as standard) and/or bezel spacers to hide this gap.

@user-hi2oi1yh6q 5 ай бұрын

They also sell trim rings for the boxes so the plates fit properly

@mattypants 5 ай бұрын

The reason the outlets are installed "upside down" is for safety, it has nothing to do with how plugs are oriented. If ground is up and the plug is somewhat out of the wall, something slides down there, it hits ground, no trouble. If it's oriented the other way, then the item crosses the hot and neutral and causes a short, spark, possible fire. Homes should also have them installed that way. Any electrical done in the past decade or so in a residential will be that way also. Where I live it's code, they have to be. You also shouldn't use a power drill to for electrical, you're bound to strip something. They make box spacers to deal with that 1/4 gap or some 1/2x1/4 wood bits and a chop saw.

@randallwainwright190 17 күн бұрын

That's the way to protect it

@richardzicarelli3193 5 ай бұрын

Can you use your CNC router one day to make some 1/4” thick frames to go around the electrical boxes and behind the outlet covers?

@troybrodrick7208 4 ай бұрын

use the foam insulation for outlets .just cut it out to just cover the gap

@joshruby 5 ай бұрын

Use the oscillating saw to trim boxes back 1/4 inch flush with wall I’ve did it before

@jrmediate 5 ай бұрын

Never mind, I see the mounting point goes right to the back of the box, so that would work!

@yellowhammerwoodcrafts 5 ай бұрын

There is no upside down or not for outlets. The reason some outlets are ground up is for safety because if something falls on it, it will hit the ground first. Most hospitals have them ground up. It’s definitely not wrong and neither is ground down.

@danielheartsill4269 5 ай бұрын

In our area I understand it is code to put the sockets in like you did, so you did good. Also get some 1/4 inch wood and make a frame around the box to have no space behind the plate. All problems solved.

@clydedecker765 5 ай бұрын

I admit that prongs up LOOKS right but the SAFEST is Ground UP because anything dropping across the plugged in cable will strike the ground first NOT the hot prongs. However that is kind of hard to do to strike a cable near the wall and pull it out slightly enough to allow clearance to the prongs enough to create a short across the plugs' prongs. Hard to do unless you're a child with a table knife sliding the knife down the wall.... Yeah, kids find a way.

@sirwallygator565 5 ай бұрын

Make decretive 1/4 inch thick wood things that go around your boxes. like frame them in like a picture... urn your outlets so the ground face down.. Yes I know many have their own opinions on this. Electrical code does not states orientation but take it from experience all items made in North America are made to fit the outlets with the ground down...Ground up is the old way they did things that is why many factories and ld houses had the ground up but their is a lot of engineers talk about the benefits of having the ground down

@rmorris3722 5 ай бұрын

I know what I would, and you have the equipment to fix it. I like ground up also.

@MJMCHRONICLES 5 ай бұрын

Make some Samcraft 1/4” back plates for your wall receptacles, it will look cool

@suzylarry1 5 ай бұрын

you said this is a sub panel , I saw a green ground screw that connects the panel with neutrals' , that screw should be removed ( If I recall ) so ground and neutral are separate on sub panels . correct if I am wrong do to different power source ( solor)

@JeremyEllis43787 5 ай бұрын

I always put tape covering the wire conections

@doowroh 5 ай бұрын

surprised you went with those style switches and receptacles, straight outta the 80s.

@charlesdeaton7112 5 ай бұрын

In theory the ground on top is supposed to keep the plug in place. My shop is done the same.

@user-hi2oi1yh6q 5 ай бұрын

Sam, did install an 1to 1 isolation harmonic transformer on your computer equipment so you can operate things at the same time.

@jasonelliott2055 5 ай бұрын

I've not read any of the other 160 comments. Take your laser and some 1/4" material and make some "decorative" plates to go behind your covers. You could let your kids decorate them before installation.

@robinderick947 5 ай бұрын

Put trim around them. Use what you put on the walls 😊

@cantgetright742 5 ай бұрын

I like the comment that says make you a decorative surround for your cover plates. Might as well display some of your work in the workshop and it solves a “problem”. My receptacles are sideways

@tim-hypnotherapist 5 ай бұрын

Just put a small border around it. About 1 inch surround 1/8 or 1/4 inch thick, either glued down or the plate holds it on.

@packy0462 5 ай бұрын

Looks good what was the wire stripper you used

@mitchellbagby92 5 ай бұрын

Add a fome the plat

@loissaedder2214 5 ай бұрын

Your power points are nothing like ours in Australia. We have on/off switches on ours . Also your light switches are opposite to ours. Ours are up for off, down for on.

@danbailey96 5 ай бұрын

I'm a licensed electrician and general contractor and on commercial I usually install up and residential down because that's how most people have seen the outlets oriented.

@angels12a 5 ай бұрын

Maybe you make a spacer to set behind the wall plate?

@jraiello 5 ай бұрын

Easy fix, 3 d print cover backing spacers same color or whatever desired…

@JimG31547 5 ай бұрын

Sam, Crank up the Shapeoko and Carve and cut you some outlet covers and pocket the back where they will lay flat.

@carolmirci1233 5 ай бұрын

Sam take you laser and cut out like picture frames to go behind the outlets either make them flush with the edge of the plate or make them go out a quarter inch or so and paint them a different color to highlight them. Cool think outside of the box . How about different shapes triangles circles diamonds possibilities are endless