Diesel Kerosene Forced Air Heater FIX EVERYTHING

Рет қаралды 321,926

Жыл бұрын

Cheapest/easiest way to heat a shop is with Diesel/Kerosene. The only thing cheaper is wood or natural gas. They have these in Propane as well but Propane has a lot less BTU and is about 25% more cost to run vs diesel.
🔥
✔️Test PRESSURE GAUGE HOOK UP: amzn.to/3SC3GGF
PERMANENT PRESSURE GAUGE: you need an extension➡️ amzn.to/3hxn8XY and the gauge amzn.to/3fRNB2f
3m TEMFLEX rubber splicing tape: amzn.to/3f7I9YM
Carbide Burrs for metal: amzn.to/3W8AXfm
BULK Foam for filters(great for small engines): amzn.to/3U6Th74
Gasket-Rear Housing-Check ball: amzn.to/3U0DXZr
Universal SPARK coil: amzn.to/3svQkkC
Impeller Blades 1/2in thick: amzn.to/3TZShS1
🔴
DESA heater with RECTANGULAR rear assembly
Complete rebuild kit: amzn.to/3sAxxEQ
🤔Why these can put out ZERO Carbon Monoxide: Simple, CO is created from unburnt hydrocarbons and with this tuned correctly you are burning everything completely. So you'll say "But a diesel engine or gas produce CO all the time..." Well this is necessary with an engine as it keeps an engine(valves/piston) cool. If you ran an engine with a lean mixture it will literally melt, also an engine requires a rich mixture when cold to help it run smoothly. With a heater like this we want it to run as hot as possible. Now if you just burnt a flame of diesel/kerosene out in the open it wouldn't burn completely and put off black smoke. This is because not enough oxygen can reach it fast enough. The "forced air" part of this heater keeps the fresh oxygen continually in contact with the fuel. They can however deplete oxygen as they consume fuel/oxygen, so you need to allow occasional fresh air or you will get low oxygen levels.
⚠️SUPPORT THE CHANNEL or support the SHOP DOG's treat addiction:
Buy Ginger a new bone: www.paypal.com/donate/?hosted...
👀 sixtyfiveford
👀 sixtyfiveford/
Ginger's Wish List
www.amazon.com/registries/bir...
65 Ford
65Ford
Magic words to a spell that will enchant your heater:
Shop Furnace, Garage Heater, outdoor heater, Desa Ready heater Reddy Remington Vanguard CO-OP Master All Pro Glow Warm Universal Portable Heaters Mr Heater Dayton Dynaglo Dyna Glo Craftsman Dewalt Heat Fast Montgomery Wards Sears Home Depot Lowes kersene deisel 40,000 50000 55000 60000 70000 80000 90000 100000 110000 120000 130000 140000 BTU

Пікірлер: 579

@lacro5686 Жыл бұрын

I used to be a tech for these heaters many years ago. The biggest problem I found with them is water and dirt in the fuel. They really should be run on kerosene, not diesel. If the heater is stored with a partial tank of fuel in the off season the filler cap vent will allow humid summer air to enter the tank and condense. The water being heavier than kerosene will settle on the bottom, and rust the tank. Look in the tank with a flashlight to see if there is water. It's best to drain the tank at the end of the season. Or - fill the tank completely so no humid air can enter during storage. The fine mesh fuel filter tends to collect lint, and should be checked/cleaned frequently. I learned lots of tips and tricks over the 35 years I worked on these heaters, but they are too numerous to mention here. One tip I will share is to always start the heater facing outside for the initial cold start. When the raw fuel hits the cold nose cone (aka afterburner) it will cause a puff of smoke (partially burned fuel) and stink. Starting the heater outside, and allowing the nose cone to become bright red (slightly dark in the middle) and then bringing it inside will prevent the stink from filling your shop. The heater only burns clean when the cone is red.

@FireSkittlez85 Жыл бұрын

Thank you for sharing, I bought one to keep my shop warm for a little while. Will keep these things in mind.

@Fine_art_aerial Жыл бұрын

I have a redline 150,000 btu heater and it fires up good and runs for maybe 3-5 minutes then shuts down/fills garage with black smoke.. Replaced the spark plug but still does it.. Any ideas how to fix?? Thanks brother!!

@lacro5686 Жыл бұрын

@@Fine_art_aerial try removing the nozzle and take it apart to check for dirt. also, on the 150 BTU models, there is an in-line filter that gets clogged with lint. It's located inside the flare of the fuel pick-up tube. It's removable for cleaning. The air outlet filter could be clogged, and needs replacement. It's the felt one with the cork surround. There could be a spider or mud dobber in the air adjuster screw.Check inside the tank for dirty fuel or water. Use a flashlight. Lot's of possibilities.

@BumpNrun69 Жыл бұрын

Wow, pretty much the info I was looking for. Just recently purchased one that can run on 4 different types of fuels/oils. Been running kerosene which has an odor to it and was wondering if diesel's odor would be any less noticeable. Borrowed a buddy's kerosene can and need to purchase either a kerosene or diesel can for myself but didn't want to make that $100 plus commitment with a Justrite can, until I found out what's best. Appears kerosene's the way to go, thanks.

@jacobgriffin6812 Жыл бұрын

What would cause a 215000btu heater to shut off after a few minutes and not restart and have hard starting issues?

@rogerjustice8835 Жыл бұрын

I own 2 of these heaters, made by desa they are as reliable as a stone and super simple to repair and service. I’ve always ran them on number 2 diesel both on road and off road grade, wouldn’t trade either one for any other heater. Years ago I bought a plug in thermostat for them that way I can set a temperature and not have to constantly tend to the heater it cycles on and off like a furnace.

@sixtyfiveford Жыл бұрын

I've had a few with thermostats and that is nice.

@alancummings5008 Жыл бұрын

I wired a baseboard heater thermostat(garage sale find) into a 10 gauge flat extention cord. Hung the thermostat about chest high. Ran my heaters for years.

@leelovins334 Жыл бұрын

Excellent video I have a cupple at my shop I'm going to repair thanks

@mrcaboosevg6089 Жыл бұрын

My dad got one of these back in the 70s, nearly 50 years later i'm still using it now. As a kid having what i called a rocket in the garage was a lot of fun

@astick7777 Жыл бұрын

I have those same memories

@jacknevitt7384 Жыл бұрын

I was always curious about these “jet engine” heaters and how they worked. Great video, thanks!

@sixtyfiveford Жыл бұрын

Thanks Jack. -Moe

@heisenberg3868 Жыл бұрын

Finally somebody that actually explains servicing these heaters properly everybody else is so maybe on half the shit thank you I appreciate it

@vinces8974 Жыл бұрын

Great explanation, on how these torpedo heaters work,you never fail to impress me with your knowledge on how to fix things, your video are brilliant .

@StewsChannel Жыл бұрын

Super informative! I see these at garage sales for almost giveaway prices because they dont work. Next time I see one, I'll scoop it and tune it up for a temp garage heater! 👍 For some reason I always thought they would be more complex inside.

@sixtyfiveford Жыл бұрын

Anytime I find them under $25 I scoop them up. They don't resale for a ton but generally still fetch $150 in the heart of winter.

@notgivennotgiven7776 Жыл бұрын

Man dude, you always find the coolest junk. I came for the heater and stayed for the dog trick. Peace

@alancummings5008 Жыл бұрын

Had a couple of these over the years. Picked up at garage sales for next to nothing. Through cleaning. Adjust pressures. Worked great. Thanks for sharing

@sixtyfiveford Жыл бұрын

Right on

@vampirejesus8170 Жыл бұрын

Got one of these from a garage sale a few years ago. Cleaned up the outside and replaced the outside filter. Been running every winter in my garage when I needed it to. Best 20 bucks I have spent in a long time.

@ogresspeedshop 4 ай бұрын

This was the video I didn’t even know I was looking for. I just picked up a heater very similar to the one you’re working on. Got it for $40 at an estate sale and I took it home, plugged it in and it fired right up. Had a pretty good fire show fly out from the rats nest inside it, but it worked great. Finding this video answered a lot of questions I had about how it actually worked. Thank you for that and awesome informative video!!

@multicyclist Жыл бұрын

Well I am impressed. I never knew those things could burn that clean. The last time I used one of those was in the 80s to heat the unheated bay of a heated shop when needed during freezing winter weather. Even though it was near new, it would burn your lungs from the fumes if the bay door was not open (which defeated running a heater). Definitely would be worth having one around the house for use outside now that I know they can burn so clean without all the fumes and CO. Thanks!

@multicyclist Жыл бұрын

I just realized the reason why the near new heater put out so much fumes (back in 1987). The altitude was 5600 feet above sea level. Had I had known {or realized) back then what you shown here I am sure it would have burned cleanly.

@TheChewy78 Жыл бұрын

And also ultra low sulfur diesel helps too

@hmac2476 Жыл бұрын

Outstanding! I'm never disappointed when I watch your tutorials. Thanks and keep em coming.

@sixtyfiveford Жыл бұрын

Awesome, thank you!

@davedennis6042 Жыл бұрын

Wow, that was some real quality content. Probably not a dozen people know how to properly run these. Thanks.

@billvandorn5332 Жыл бұрын

I dove into repairing one. Helped me tremendously getting my tractor to warm up and start in the freezing Winter storm last year. Game changer!

@carlnelson3893 Жыл бұрын

I have 2 similar one in my garage for 10 years, now I have the knowledge the go thru them, Thank you!

@Palmit_ Жыл бұрын

Hey Red and Ginger :) glad to see you both well and happy :D 15:38 - thats "self-amalgamating" rubber tape. it merges with itself. like the borg off of star trek. it assimilates the given info (shape) and moulds itself to that when merging. brilliant stuff.

@rupertthomson Жыл бұрын

That black tape is called "Self Amalgamating Tape" in the UK, maybe it is in other places too, if anyone is searching for it. It is very useful stuff!

@tellyfaulkner3466 Жыл бұрын

Australia as well.

@rangerriggs5066 Жыл бұрын

I’ve always called it Live Rubber here in the states, don’t know if that’s the industry terminology or if it was an odd name my grandfather knew

@preludedude4765 Жыл бұрын

Well you just sold me on these. I was in the same boat of thinking they would gas me out as I've seen several that do smell. Glad to know there's ways to make it right and make it safe. Thank you

@Texasknowhow Жыл бұрын

I picked up 3 of these at a garage sale for $15! They all need to be gone through and checked out. Two of them are the same size as yours in the video. Orange and everything. The other one is almost twice as large, white in color and a different brand. This video and a little cooler weather is making me want to dig into them and see if I can resurrect them. 😊

@dieselrotor Жыл бұрын

By far, the most useful and informative video I've seen in years. I've passed on free Salamanders because I didn't know they were this repairable, having never owned one Myself not needing one. But now I have a use for one and will keep My eyes open. Thank You.

@servingme09 Жыл бұрын

I now know how to fix my Torpedo heater, had tried several times without success but now I'll be able to fix it, thanks for the tutorial.

@ZippoVarga Жыл бұрын

I've been lucky enough to have three Farm King high pressure heaters over the years that'll burn anything from Kero to diesel to home heating oil and filtered used motor oil. Of course, the filtered motor oil does tend to gum things up more than the rest, but in small quantities diluted in the kero or diesel, it does just fine. They actually run Wayne or Maxon (located here in Muncie) burner assemblies and typically run between 95 and 105psi. Depending on what fuel oil you use, a simple air vein shield is adjusted to achieve optimal burn. Different size nozzles are available from my local HVAC supply house. I love these things because they're quiet, efficient and so versatile and easy to maintain. But I do have a low pressure backup heater that I use for the detached garage when I start the motorcycles in the Winter. Regardless, they're handier than a third hand! Thanks for this video Moe! Zip~

@sixtyfiveford Жыл бұрын

Your Farm Kings are neat and I recall the videos you did one them. I have never come across one locally.

@orvillehorner4326 Жыл бұрын

Used motor oil..filter good.. Get the oil up to about 130 degree..be for u starting it.. Seems to help..

@20havenfun08 Жыл бұрын

I've worked on 6-8 of these units. Great video, learned more than I thought I would have.... thank you:)

@sixtyfiveford Жыл бұрын

Awesome.

@kalleklp7291 Жыл бұрын

You put new life into this thing and made it useful again. :) Nice job and it probably helps me out when I get to fumble around with my heater...thanks.

@raymondcollyear4773 Жыл бұрын

Just like everyone has already said great video. I have a heater and It quit heating a couple of years ago and I didn't know how to fix it till I watch your video. So now I feel I can try and tackle trying to fix it because my youngest son bought a house and he needs a heater for his garage. Thank you for sharing what you know

@wangofree Жыл бұрын

Thank you. I've used mine for years without doing anything to them. I need to eyeball the filters and check the bushings. You are a master mechanic.

@donaldrichards9604 Жыл бұрын

What a spectacular DYI video. Very thorough. Exceptional explanations

@johnpossum556 Жыл бұрын

When I had a garage I ran a 110,000 BTU one in a 2.5 car uninsulated garage. Even in -20F it would heat up in about 20 minutes. I did put a CO detector in there and it never registered any CO. A friend gave me a thermostatic switch from a 120V electric oil radiator that I wired inline so about every 30 minutes it would cycle on for 5 minutes. Great system in colder states, never seen the inside of one until today. Thanks!

@jhartford58 Жыл бұрын

Just discovered your channel. Thank you for the quality in-depth content.

@kevinstraitiff6318 Жыл бұрын

Love your videos. You know what you're talking about and convey your knowledge extremely well. I was looking at buying a furnace for my large garage, but after watching your videos, I realized I have heaters to tune and a drier i can modify. Subscribing for sure. Also, love your dog. :)

@haneyoakie14 Жыл бұрын

I inherited one of these and don’t know anything about them. Until today! Now I have a basic education of what I’m looking at. Thanks for the great content.

@sixtyfiveford Жыл бұрын

Right on!

@cr76802 Жыл бұрын

I've rebuilt a few of them It's amazing how easy they are to fix and swap out

@seastacker8582 Жыл бұрын

I picked up one of these years ago for $25. Would sort of light then blow out. It was that rear plastic cap was cracked. Easy fix. Set the pressure with a harbor freight gauge. Been running for years trouble free. Great video.

@rafaelrodriguez-vx6ck Жыл бұрын

Your videos are helpful and your dog is one of a kind. Keep the on keeping on. Thank you

@donlehocky7348 4 ай бұрын

I bought one of these about 30 years ago for my 2.5 stall garage/shop. Still going strong. Found this video and did a little tune on it. Was getting fumes, so I backed off the fuel a bit and now no more fumes.

@bobfugazy4916 Жыл бұрын

This was great, thank you. I grew up with these in my Dad's garage.

@tomayrscotland6890 Жыл бұрын

That is a good quality service you did there, And very instructional too. well done.

@starfish5479 Жыл бұрын

I have one identical to that one Co-op decal and all. I bought it when I was 18 years old. I'm 68 now! It still works perfect!

@sixtyfiveford Жыл бұрын

That's neat.

@nickklaas4776 Жыл бұрын

After watching your vid a few times I got a free one of these that had been left outdoors for years. The tank was full of water and the foam and screens were done or missing. I tore it most of the way down. Bought some parts, some adapters and $15 of kerosene. When it fired up the heat blew my mind!! This one took quite a while but I could do the next one MUCH faster. A fun project and now I have a working heater for the garage for under $30! THANKS for the great video

@TRUMPUSA1 Жыл бұрын

I like my similar 35k btu propane heater. We used one like in the video on many cold nights wrenching in the garage! It easily heated the room! Great video. Thank you! 🔥

@MrTimdtoolman1 Жыл бұрын

I had one of these that I got used 35 years ago that had the cone melted off of it when I got it and someone before me had put a square metal J-box cover over the front for the "cone", I used it to heat my garage at home in the winter when I went out there to smoke cigarettes in the winter. It worked fine for years only smelling a little kerosene when it first started up. It finally stopped working 10-15 years later and I got rid of it and found a better smaller BTU unit that was intact but I have not used it for years since I don't smoke in my garage, or at all anymore. I love your channel brother, I'm 60 now but I always learn something interesting in your videos. You are like Mr. Wizard as far as I'm concerned, so keep up the great vids, and Ginger has become quite the Star.

@taiguy4961 Жыл бұрын

Amazing video. I am looking to purchase my first heater and with basic knowledge of ICE’s and carburetors, You have thought me all I need to know to get started right off and a jump on maintenance. Thanks!

@richardross7219 Жыл бұрын

Nice job. I just picked up one of these for free. Now I have a better idea of how to fix it up. Good Luck, Rick

@sixtyfiveford Жыл бұрын

Cool, thanks

@Its_Me_Wheelz Жыл бұрын

When I worked in construction years ago, I used to possess these heaters. I was foolish and short-sighted when I sold my business, so I also let my heaters go. A man who has had his seat for more than 20 years will soon sell one to me. I'm buying it for a very low price-like $25 low. What I need to do as soon as I acquire it is being demonstrated in this video step by step. I'm grateful.

@That_gasser_1st_gen Жыл бұрын

Got reccomended this video right after mine started acting up. Gunna give these tips a shot, thank you so much for the info!

@bigDbigDbigD Жыл бұрын

Moe, this channel has the most useful information to guys like me on youtube!

@sixtyfiveford Жыл бұрын

Glad you think so!

@headpainter1 Жыл бұрын

I had a friend give me his because it quit working. It had bounced around in the bed of his truck and had a crack in that plastic housing for the air pressure. I siliconed it up and walla, worked again. I didn't fully understand why it worked but knew the crack shouldn't be there. Thanks to your video, I know now. I really appreciate your content.

@sixtyfiveford Жыл бұрын

Awesome

@flocksbyknight Жыл бұрын

Well done my friend. Thank you for showing the internals of over of these and demystifying the supposed danger.

@sixtyfiveford Жыл бұрын

Hey Thanks.

@Farm_fab Жыл бұрын

I got one of these at the scrap yard, and it need a HV transformer. I called around and none were available. I then looked into a neon sign transformer, and the output was similar, and it was more than two thirds less than OEM, and it worked very well.

@Enigma-Sapiens Жыл бұрын

Great video and How-To Moe. Very useful information, thank you! That girl is talented and smart! Those dogs never cease to amaze me.

@Manandmachine772 Жыл бұрын

I always wondered how they worked and was hesitant to buy them at yard sales. But not anymore Thanks for sharing this knowledge.

@sixtyfiveford Жыл бұрын

I always buy them if they are under $25 non working.

@noiwanttobeanonymous3797 Жыл бұрын

When these were around in 1967 for garage's and farm's they were called Tropical heaters and used paraffin Esso blue or Alladin pink they burnt without smell and were fantastic.

@edf7008 Жыл бұрын

I am amazed at what you can fix or repair. Thanks again for this bit of info! :)

@lilmike2710 Жыл бұрын

We used those back when I was working in paint and drywall. They definitely work well heating large areas. The fumes aren't bad unless you allow it to run out of fuel whilst running. Excellent for helping latex paints and sheetrock compounds dry in winter. But they're not worth a 💩 for helping oil based paints and enamels drying. They'll actually prolong it. Like trying to dry latex paint with a water humidifier.

@rayschmal5672 Жыл бұрын

I thoroughly enjoy watching your KZfaq videos thank you so much keep it up

@sixtyfiveford Жыл бұрын

Thanks Ray. -Moe

@Mrcaffinebean Жыл бұрын

I have one of these and just as you say they run very efficiently. I bought mine used also and it's the best $50 I have spent on the shop.

@Snailmailtrucker Жыл бұрын

Great timing once again my friend... I love using my shop heater (exactly like the one you are showing!) I bought mine on Craigslist for $20.00 about 5 years ago and use it in my shop every winter.. I only use diesel fuel and very seldom have any smells except at start up and maybe shut down ! I usually start and stop outside! Keep the Faith Brother !

@sixtyfiveford Жыл бұрын

Awesome

@gregorypiercesr.2769 Жыл бұрын

I have used them in the dead of winter to keep heat in friends of mine well houses to keep the water flowing and they work fantastic!👍👍👍! Super detailed video!!

@sixtyfiveford Жыл бұрын

That's awesome.

@R3TR0R4V3 Жыл бұрын

I have one of these too, which was brought back from the dead.. Great heater! 😎

@joeycmore Жыл бұрын

Thanks. I actually have one of these awaiting me to fix it for the past 20 years! I keep chickening out because I have never worked on heating equip. Now I lost my excuses. Great!

@sixtyfiveford Жыл бұрын

Right on

@davidstansbury3204 Жыл бұрын

Thanks for your time and knowledge. I’m going to dig out my old one and see if I can get it working. Thanks again

@BacktotheBasics101 Жыл бұрын

I have an actual nipco heater that I bought secondhand at an auction sale and have been using it for years with relatively no problems. I sometimes use number to fuel and if I don’t put additive to it, it does seem to freeze up. I don’t know what I would do without it. Thanks again for the awesome breakdown video. This video will be very useful.

@DconBlueZ Жыл бұрын

Thanks for the video, always enjoy watching!

@sixtyfiveford Жыл бұрын

Thanks for watching!

@Popeyes66 Жыл бұрын

You know a lot about a lot of things. That is why i subscribed. You also have a great weird lookin dog which i love. Always a pleasure to view your content. Thanks .

@ItsaRomethingeveryday Жыл бұрын

This is second video I've watched from you today, Liked n Subscribed

@scottyellis3442 Жыл бұрын

Great video, I wish I had seen this 20 years ago "but 20 years ago there was no KZfaq LOL". Back in my sheetrock days we burned a 150,000 BTU ready heater & it only smelled at first start up.

@MyDIYAdventures Жыл бұрын

I was worried for a second! I was thinking “is he NOT going to fab up a handle for it?”😂

@ZPDSurvival 9 ай бұрын

I just picked up a 1963 Electro Magic Kota Model 740 for free. Very nice condition. Looks older school than the one you are working on. I am going to try and fire it up. Great Video.

@sixtyfiveford 9 ай бұрын

Very nice!

@johndoe43 Жыл бұрын

Good job. I had a new teddy heater. Used it twice and it got stolen. Thanks for the info. Makes me want to buy another one.

@kennethparker2168 Жыл бұрын

I have one I bought in the mid seventies It kept me from freezing to death working on cars in a garage and sometimes outside in Wyoming it has a rubber air pump that went bad it was such a valuable tool I still have it after watching this video I will try to get the part from the company he says make most of them and use it some more

@cmleoj Жыл бұрын

Very informative video. I learned a lot. Thank you.

@billrimmer5596 Жыл бұрын

I need me one of them. Great job as usual!!

@sixtyfiveford Жыл бұрын

Thanks!

@Dennis-uc2gm Жыл бұрын

When you have to swap a water pump on a car in the Midwest in the middle of January these can be worth their weight in gold . I've had a Redi-Heater for 25 years plus and have only had to do minor things to keep it going. Great video for when I've got to go deeper.

@sixtyfiveford Жыл бұрын

I agree! Absolutely a lifesaver outdoors.

@chipwright6193 Жыл бұрын

I saved one of these they were throwing out at work. I've been wanting to go completely through it and get it running again. It hasn't run in maybe 10 years and it's probably 20 or 30 years old. I like how simply they are built.

@mhpjii Жыл бұрын

Man, do I respect you for your knowledge!

@sixtyfiveford Жыл бұрын

I appreciate that

@Scrapy-ih7ob Жыл бұрын

very nice video. i was supposed to scrap one of these today but forgot to throw off the truck. wasn't sure if was missing parts. so tomorrow if another person hasn't taken it, going try bringing back to life. with the help of your video. At least now i know what to look for. Nice video

@sixtyfiveford Жыл бұрын

Right on

@isaiahvillarreal4512 Жыл бұрын

I saw this post yesterday and lo and behold I’m out looking around the 5 acre property I just bought from the widow of an old hoarder. Found one same faded orange.

@RPS2443 Жыл бұрын

I had one of these that was a hand me down from my grandpa. It obviously wasn't "tuned" because it smelled terrible and burned my eyes. I think it ended up in the landfill because I didn't know how to fix it. 30 years too late, but I'll try to fix the next one I run across!

@jeep2003 Жыл бұрын

Man you are great at fixing stuff! Iv had a few that i couldnt figure out. Iv been using propane because it doesnt stink up my garage but it doesnt heat very well. Im gonna go back to the torpedo and make sure she's burning right. Thanks!

@robertwoodward4525 Жыл бұрын

Try the diesel fuel. I think it does not smell as bad as the kerosene

@jeep2003 Жыл бұрын

@@robertwoodward4525 Iv been using fuel oil actually. Probably the worst of the three i dont know

@jothain Жыл бұрын

Very good overview of how these work.👍🏻👍🏻

@sixtyfiveford Жыл бұрын

Thanks! 👍

@chrissscottt Жыл бұрын

Love watching this dude.

@wayneo7307 Жыл бұрын

Nice Job Moe ! She Looks And Runs Great Now ! I Used to Use These in Winter Doing Framing All the Time ! Great For Doing Everything ! Just don't put anything too Close !

@sixtyfiveford Жыл бұрын

They pump out a lot of heat.

@yodasbff3395 Жыл бұрын

Great video, 👍, thanks. Thieves got my Ready Heater so I replaced it with an electric furnace that a friend removed from his house. The furnace is slower to heat the garage but I like how it is much quieter. Yoda and I ❤️ Ginger.

@sixtyfiveford Жыл бұрын

The noise is my only complaint with these. Ginger says HEY YODA!

@dannybowman7792 Жыл бұрын

Thank you for the info. You're a great teacher. I appreciate this video.

@wyattoneable Жыл бұрын

Great save and well explained Moe!

@davidschwartz5127 Жыл бұрын

I've owned 4 of those jet engine heaters during my lifetime, only bought one though, and the rest were given to me by several clients because they stank up the building they were being used in. Actually, the one I bought was an LP gas unit for the very same reason and I still have it today and it still works fine after 50 years. For the other three, I was told the spark plugs were most likely bad and I changed the plugs but made no difference they still smelled so I donated to Habitat for Humanity years ago. I may have to keep one of them and fix them, (not fooling around with the 20# LP bottle has its advantages) if I had seen this video first there really is not much to them under the hood. Thanks, I learned a great deal.

@lacro5686 Жыл бұрын

Depending on the BTU's of the propane models, they won't run on a single 20# bottle. I had a 150K BTU unit and it would only run about half the 20# bottle before it quit vaporizing the fuel. I had better luck Mani-folding 2- 20# bottles together. The 150K heaters really need 100# bottles to be efficient. Also, they are really loud....

@ke6bnl Жыл бұрын

thanks for your help got mine working after sitting out for about 10 years. fuel was plugged and the photo eye would not sense the flame. But it is toasty in the garage.

@2LateIWon Жыл бұрын

Nice save. These really are great heaters.

@sixtyfiveford Жыл бұрын

I just love how fast they heat up.

@Stover1928 11 ай бұрын

Excellent video. You are very knowledgeable. Helpful

@haydenc2742 Жыл бұрын

Way cool! Great job! Keep em coming!!!!

@LB-og4wl Жыл бұрын

You do amazing work!! Got to say I love your video so much good info! I would love to see you do some work with the heater to see if it could be used with used cooking oil or used motor oil safely.

@paulblackman4833 Жыл бұрын

Another informative and educational video.💯

@sixtyfiveford Жыл бұрын

Hey Thanks.

@ChrisWiles-nu4sk 10 ай бұрын

I love it. I does the job of keeping me warm.

@C-M-E Жыл бұрын

My favorite commercially-available Poor Man's Jet Engine. I looked at the operating principle some years back when making my jet engine developed for testing high temp composite parts, but ended up using jet engine parts like compressors, combustor liners and fuel nozzles for inherent durability. It's also doubles as my forge burner coincidentally during the lovely Texas summers when feeling like I need more heat is the least of my concerns! At any rate, I'm surprised more people don't use these for waste oil forge burners. Lil bit of fiddling would get these extraordinarily hot, though you'd need some pretty intense heat shielding to compensate compared to what you get on these models. 🔥

@sixtyfiveford Жыл бұрын

Awesome!

@adnacraigo6590 Жыл бұрын

Dandy exploration. I have never seen inside of one of those heaters but they sure do throw out the heat in a hurry.

@patrickc8190 5 ай бұрын

Thanks for the information , well done and explained.

@astick7777 Жыл бұрын

These are great shop heaters.

@darellsunderlin4670 Жыл бұрын

I've fixed many of these, and have got may throw aways like your that with little effort can be fixed , best two were a 150,000 BTU and a 165,000 Btu !! Great video .

@sixtyfiveford Жыл бұрын

I have have a few around 150k and they are amazing but way too much for my 2 car garage. 50k, maybe 100k seams about right.

@scottfirman Жыл бұрын

Good video. I have never pulled one down as far as you have. I had to replace the fuel line as well, as you stated, mine was split and sucking air. Those things can sit forever and still run. I would replace that sensor as it is a safety feature that should be functioning. I had to use one under my mobile home when our hear tape got chewed by a mouse and even though the pilot light said it was functioning, it was not. That torpedo heater quickly thawed my water lines and I replaced the heat tape.