Will Dad's Favorite Tractor Ever Run Again? Part 1 Installing The Crank Shaft and Mains!

Рет қаралды 11,785

10 ай бұрын

#tractors #johndeere #repair
putting the new crank shaft in Dad's John Deere 720 Two-cylinder diesel this is a video covering the crank shaft being put in and the rods being re connected to the crank and then putting the main bearings in and the right side first reduction gear case oil seal on the crank shaft

Пікірлер: 43

@peteschiavoni 10 ай бұрын

So happy to see dad’s baby going back together. A full resto will be great.

@garethstott 10 ай бұрын

'Now Mom don`t be yelling at dad about this' 😂😂

@seancombs499 10 ай бұрын

Like how Dad is letting all you guys be involved in putting it back together. Like ya said you two have done a lot on them ole two cylinders dad can prob put it all back in is sleep lol. Glad to see it going back together bud

@jonathancrissinger2301 10 ай бұрын

Thanks for explaining the various things about the little parts and pieces. It makes it more interesting to watch.

@scrotiemcboogerballs1981 10 ай бұрын

Glad you got the parts you needed thank you for sharing It sure was easy taking it out when it’s two pieces lol

@garybarrett6581 10 ай бұрын

wish l could of ran into you at Rantoul We had our D17 D there plowing!!! l will be watchin!!!!

@roberthocking9138 10 ай бұрын

LOL I loved the red hand painter 😂 , well done guys. For a minute there I thought you were putting it in without assembly lube 😬

@charlietanner6211 10 ай бұрын

gotta love them to put that much in one

@tylershumaker4152 10 ай бұрын

Glad you were happy with the crank shaft. That had some of the nicest splines, I've seen on a diesel crank

@wademizelle3433 10 ай бұрын

Great video, a lot of old timers watching. Can’t wait for the next one. Thanks

@dirtgrainsteel 10 ай бұрын

Glad you enjoyed it thank you!

@randybedker1584 10 ай бұрын

When you work as hard as you guys do you gotta have some fun with all your money..😂😂

@jazzerbyte 10 ай бұрын

It will all be worth every penny in the end when the old iron is in top tune!

@CaryGuyer 10 ай бұрын

Very well presented and detailed how to video on that particular process. You will have that thing running like a top when complete.

@garethstott 10 ай бұрын

Great to see you passing on the hands on experience to the next gen.

@brittblanton8342 10 ай бұрын

Great video Brandon, nice to see how it’s done 👍

@garymessina1609 10 ай бұрын

Great job great video thanks Brandon and George and dad and Tyler

@Spitter-ud8jd 10 ай бұрын

Torque spec. on a John Deere 720 main bearing is [German] which = Goot n Tight.🍻

@jeffkluesner1895 10 ай бұрын

I’m glad to see you are fixing that tractor too good of a tractor to part. I have an early model here in Iowa I would fix mine if that happened to me good luck and keep up the good work

@danw6014 10 ай бұрын

$4,000!? Don't say that. I've got a 730 diesel waiting for a complete overhaul. One thought I had for setting the crank in place without marking up the journals. 3M vet wrap would protect them without leaving any adhesive behind. The other thing I like to do is use aviation gasket maker on the gaskets. I put a very thin film on and I think it seals any deformities in the metal plus holds the gasket in place because it gets tacky after a few minutes. Just my $2.00 because two cents won't buy bubble gum anymore. Great video. Can't wait to see the rest of the series.

@artillerest43rdva7 10 ай бұрын

great to see progress on the tractor! keep up the great job.

@georgejones-nz1qg 17 күн бұрын

If you make a serious crop, you've about got to overhaul them old popping Johnnies every winter.

@79fordblake 10 ай бұрын

Glad to see it's going back together!! Send the pumps and injectors to Garry Power. :)

@dirtgrainsteel 10 ай бұрын

That's exactly where they are going!

@phud9657 10 ай бұрын

👍👍

@johnnyholland8765 10 ай бұрын

That tractor is worth spending the money on. The rest of it is in good condition so yes. Beside your Dad has to spend his money on something for fun. His hobby just happens to be a somewhat expensive one. Just look at it as another farm repair...

@oldamericaniron5767 10 ай бұрын

When working on something like that it isn’t a question of will it run again, only when.😀 I had an old friend who would say, we don’t ask it we tell it.

@dp8689 10 ай бұрын

Fifty foot pounds on center maine

@scottreasoner6126 10 ай бұрын

Did you ever find out what caused the old crankshaft to snap in two. What if the new crank does the same thing.

@dirtgrainsteel 10 ай бұрын

Come to find out it wasn't to un common for these cranks to bust even back in the day when the tractors were new....I've heard several reasons as to why they break number one reason the most popular reasons is lugging the engine for long periods of time which we never have but that's not to say some one didn't do it years ago and started the problem....this is a little bit newer crank as far actual build date so it probably won't be a issue ever again

@dcw1540 10 ай бұрын

Any idea what made it brake?good luck.😊

@user-cr3qo3xe9k 10 ай бұрын

Why didn’t you guys put a coat of oil on the bearings while installing them and torquing them down. They’ll be spinning dry till the pump gets oil to them. Maybe you did oil them but I didn’t see it being done.

@dirtgrainsteel 10 ай бұрын

Everything got white grease...we also will leave the fuel in the stop position and turn the big engine over with the pony engine to produce engine oil pressure before we allow the big engine to start and also before I put the top plates on the crank case I dumped oil down on top the crank trust me it's good and oiled up in there before it even fires lol

@rudycarlson8245 10 ай бұрын

Did you end up doing a complete engine rebuild on this tractor? What happened to it?

@user-fz9nk1bz3r 7 ай бұрын

I was always told not to touch rod bearings with your bare hands, always use rubber gloves. Just what I was always told maybe it was bull.

@dirtgrainsteel 6 ай бұрын

I've never been told that on engine bearings I was always told not to touch the sealing surfaces on ring seals for excavator and dozer final drives

@mikevaske8255 10 ай бұрын

If you are so concerned about not damaging the crank, turn your knife over, cut up, away from the crank.

@michaelisrude 10 ай бұрын

Does it help sticking your tongue out when tightening bolts?lol

@dirtgrainsteel 10 ай бұрын

Lol yes!!

@bryancovert9821 10 ай бұрын

Why did you though your father under the bus ? We know that type of things are expensive .

@user-bj7oz9mc8l 2 ай бұрын

Brandon why did you throw your father under the bus by bringing up the price of that crankshaft , if you were married you would know a happy wife could be a happy life . Better luck next time dad !!!!!