Disassembly / tear-down of a Dyson v6 battery/charger/bms assembly

Рет қаралды 17,079

2 жыл бұрын

I replaced my old Dyson vacuum battery and opened up the old one to see what was inside.
The replacement pack I bought from amazon was (affiliate link):
amzn.to/3s0c8Fn

Пікірлер: 17

@oscarorozco2130 7 күн бұрын

mine went dead second time brought a batt pack from amazon it work for a year thks for showing me how to remove housing i am a diy person in all areas now i wont wasted my time doing this will just put dyson in recycle trash i have two others that are 5 and 6 years old different brands never did what dyson did got this one recycle dyson for 70 percen off thats the only reason i brought it 4 years ago my other two work the same or better dont be fool by the name they arent any better again thks ps i like your style of diy work have subscribe to you for future diy questions

@NicksStuff 3 ай бұрын

That screw has a Torx head. A security Torx would have the nipple in the middle.

@Michel-Artois 8 ай бұрын

Hi, it's not possible to use again a disconnected Dyson BMS or a BMS with red light . It locks down definitely and must be reactivated with a special tool in the factory. And this first of all for commercial reasons . So just for the trash.... I change the cells with a chinese" Dyson" Bms without this issue, and so I can re-use it several times , with 2700 mAh high drain cells to have better capacity. I cut all tabs and the little screw above keeps the box closed , so I can easely check the balance. I add that most of 35§ batteries run,... Well, cheaper but with not so good cells compared to the Dyson cells. However Max power (too many amps) often used kills these little batteries quickly , and specially if you use this power with a half discharged battery.

@timbowman7207 2 жыл бұрын

Did you check voltage in each battery to see if it's only one that needs replacing??

@summetj 2 жыл бұрын

Good suggestion, that's a low cost easy diagnostic that I neglected. I checked, and the cells ranged from a low of 3.75 to a high of 3.91 (most were in the 3.85 range). I could replace the 3.75 volt cell, but given the 7+ year age of the pack, the fact that Dyson probably used good quality cells, and the fact that the BMS looks to be a balancing one, I doubt the lowest voltage cell is much worse than the others. [When I saw that replacement packs could be had for $35, my motivation to do cell replacements went away ;>]

@sabiya2 4 ай бұрын

Great video mate, can I replace the battery with a 12800mah replacement battery? The volts are the same as old battery it’s just a bigger mah,,current battery is 1300mah 22.2v, replacement I’ve been looking at is 12800mah and 8800mah both 22.2v, Thanks

@summetj 4 ай бұрын

As long as the voltage is the same, and it is designed for the same version vacuum, it should fit and work properly. However I have reviewed many replacement Dyson batteries that claim to have higher amp hour capacity and really do not. (So don't necessarily base your purchasing decision on a published amp hour capacity.)

@HDXFH 2 жыл бұрын

Make a milwaukee battery adaptor for that

@summetj 2 жыл бұрын

Well, in my case it would have to be Porter Cable, as my Ego batteries are much too high a voltage.

@NicksStuff 3 ай бұрын

These power tool batteries are 5S, so 18 V nominal (no matter what the marketing says) while the original Dyson is a 6S at 21.6 V. Back-of-the-napkin math says the vacuum cleaner with the power tool battery will deliver over 100 W less... It would be interesting to see a comparison of a brand new Dyson battery vs a brand new power tool battery. Like on actual suction power, not math.