DIY 0-29V 5A Bench Power Supply (XL4015 5A Step Down Module)

Рет қаралды 56,803

4 жыл бұрын

0-29V 5A Bench Power Supply make using XL4015 5A Step Down Module
Materials Required:
1. Potentiometer Knobs x2 - bit.ly/31IQDML
2. Power Connector socket Male 12V - bit.ly/3gwVx3H
3. 24V Switch On/OFF - bit.ly/2YWEdik
4. WXD3-13-2W 10K Wirewound Potentiometer x2 - bit.ly/2VP11Pk
5. Banana Socket Jack Red & Black - bit.ly/2NXszNU
6. 3mm LED Blue & Red - bit.ly/3gqrjPx
7. 3mm LED Holder x2 - bit.ly/3itkNcI
8. XL4015 5A Step Down Module - ebay.to/2BvZoPE
9. Wires
10. Wood Panels
DIY Tools Used:
DIY Table Saw - • DIY Table Saw (How to ...
DIY Clamp/ Vice - • Make A Drill Press Vis...
Mini Belt Sander (895 Motor) - • Electric Adjustable Sp...
Minleaf 96W 12V-24V Power Supply Adapter- • Minleaf 96W 12V-24V Po...
Subscribe LahisTech: bit.ly/2JHtlyc
Subscribe for more future creative project videos.
Thank you.

Пікірлер: 43

@-OmkarSawant-pe2uq 4 жыл бұрын

Sir apaka kaam bohot accha hai .......... Love ur videos😀

@englishrupe01 3 жыл бұрын

Nice job there! They are good modules too.

@kursatcantelli8331 4 жыл бұрын

it is a very clever way to usage of the module.

@abdulwahid8579 2 жыл бұрын

Good job with all the best information and knowledge

@MuhammadDaudkhanTV100 4 жыл бұрын

So super nice work

@-OmkarSawant-pe2uq 4 жыл бұрын

Sir ur too good 👍

@cas0per 19 күн бұрын

Good work sir... Please, I want to know the voltage of the LEDs used outside the board, as you did?

@miftosaurus 4 жыл бұрын

nice work! :D little advice: take a bit of masking tape and glue it over the LED meters. it will make them more readable, because they are way too bright! :D

@user-bn8in1de3o 2 жыл бұрын

К=анр111¹111111

@paolomichielin4849 3 жыл бұрын

Bel proggetto!

@kangbamz5119 2 жыл бұрын

Mantap sir....

@dr.zuckerbrot5731 4 жыл бұрын

*Moin, ich frage mich, was diese 'Netzteile' für einen Sinn haben!?* Käse! Kann denn niemand heutzutage mehr ein anständiges solides Trafo-Netzteil mit Gleichrichter, LM723 und einer Transistorendstufe mit 2N3055 aufbauen??

@dergenervte1147 4 жыл бұрын

genau!

@miftosaurus 4 жыл бұрын

simply said, those "old school trafos" are very hard to find, and the newer ones are very expensive! but these modules are cheap, and a "laptop brick" is cheap and easy to find, too. and anyway, linear power supplies are nicer hot at high amps, and these switched modules, at 4-5 amps (it depend of their ratings) are really cold... anyway, room temperature, maximum. :)

@visonardo 3 жыл бұрын

I want to know wich is the minim current (mA) that this board meassure, the sensibility

@bhssmh3885 4 жыл бұрын

Wow

@julioaraujo8239 2 жыл бұрын

Muito bom eu gostaria de comprar uma de o a 3o voltes

@GreenFart174 3 жыл бұрын

Can I solder a normal 100 kOhm resistor to a 100 kOhm multiturn potentiometer in order to get to 200 kOhm? Can't find a 200 kOhm multiturn potentiometer! My step up booster uses the 204w trimmpot

@ahs2pgamer Жыл бұрын

I used transformer 9 0 9 5408 diode in my xl4015 module. Now it shows 23 volts but after loading it becomes 9 volts, why is this happening? And what to do.

@winkyaw4512 2 жыл бұрын

Can use like as charger?

@sumitkhandelwal100 3 жыл бұрын

What about the heat

@roshanjayasinghe4505 Жыл бұрын

Can use as phone charge

@Souvik.4. Жыл бұрын

Can I use 19.5v 4.7a adapter for this xl4015 step down module?plz reply.....🙏

@kidnamedcancer Жыл бұрын

Yes

@YabghuKhan 3 жыл бұрын

great DIY work, congratulations. I have 2 questions. 1. There is no cable between the 7-segment layer and the sub-layer but how does the screen work? 2. What was the 3-pin and 2-pin on the top layer for you removed from?

@saieshwar6804 2 жыл бұрын

1. It has terminal hole there and a brass connector act as wire. 2. He removed potentiometers (Trimpots) that control voltage and current.

@pritammaity3221 3 жыл бұрын

Blue led What work

@bizarrow12 4 жыл бұрын

Can adjust the current?

@englishrupe01 3 жыл бұрын

Yes, this module is a buck-boost with CC/CV. You just short out the positive and negative outputs at a LOW voltage (4-7v) and then adjust the current limit with the potentiometers. Then it wont go above that limit.

@englishrupe01 3 жыл бұрын

I actually just read up on their instructions and they recommend using a multimeter amperage circuit to set these, so just use that by shorting it out in the same way.