would be interested to see the mathematics & calculations behind this muffler
@iiiillliiii Жыл бұрын
Отличная работа
@GPGarage1 Жыл бұрын
Thanks
@patrickharding4831Ай бұрын
I built a Flow Master copy in high school, actually sounded good too.
@irshadashraf79457 ай бұрын
Nice work
@GPGarage17 ай бұрын
Thanks
@martymccord9875 Жыл бұрын
We need sound clips
@Jollyroger054 Жыл бұрын
Finally a soundtrack that I can listen to lol. Nice muffler man, I'd love to hear a before and after on your vehicle. Thoughts on packing it with steel wool? Suppose that would make it louder, and seeing that you opted for a chambered configuration I'm guessing your aiming at noise reduction.
@gbklife212 Жыл бұрын
👍👍👏👏👏👏
@arvind3304 Жыл бұрын
Sir can you please to do chamber silencer for two stroke 100-200cc engine
@sylvioplacas22497 ай бұрын
Hello friend, I have a Dodge Dakota V6 3.9 LTS, would it be right to have a muffler like this to install on it?
@iiiillliiii Жыл бұрын
👍👍🙋🙋🙋
@wootzemperoar1223 Жыл бұрын
Sound check
@wowyummyyy Жыл бұрын
😲😲😲 😲 😲 😻 😻😻😻😻😻 👍 👍👍👍
@user-yx1sz9rc7i6 ай бұрын
This is sound muffler..?
@joeolivas4941 Жыл бұрын
Please make a corsa style muffler
@GPGarage1 Жыл бұрын
I'm thinking about making. It will be in some of future videos.
@LLlypxau4uK4 ай бұрын
хотелось бы услышать как звучит. хорошая работа👍
@GPGarage14 ай бұрын
Thanks, Unfortunately I don't have recorded sound with this muffler, the link below has the same design muffler only 3 inches, so you can see how it sounds on a bmw e39 2.5cc I6. kzfaq.info/get/bejne/h8-SlNGkxMmmeJc.html
@Mohsinkhan-vs6ib29 күн бұрын
Plz Maintend The Specification In Measurement Of The Turbo Muffler Thanks
@chintakanuwan4323 Жыл бұрын
Pls make disel car exhaust
@martinharris5017 Жыл бұрын
What kind of drill bits do you use on stainless steel?
@GPGarage1 Жыл бұрын
Wurth HSS
@dennisyoung4631 Жыл бұрын
If you can get them, 8% cobalt. When drilling stainless, go slow on the speed, and *do not let the bit dwell.* Give plenty of feed, so the bit cuts and does not rub. Rubbing will work-harden the steel - which will make it *much* harder to drill. Also, use a good cutting oil, and keep the bit well-oiled. Finally, keep your bits *sharp.* Dull bits will rub and work-harden stainless in a hurry.
@martinharris5017 Жыл бұрын
@@dennisyoung4631 Yes i've used cobalt and they are superior to SS bits on pretty much everything. As you say, speed is the killer. Cobalt bits aren't cheap mind you. Thanks for the good advice! Lots of skill and patience required :)
@user-bl6vj1lo9z Жыл бұрын
Свари "банку" под качественный двойной выхлоп. Именно "банку"
@Horse55 Жыл бұрын
Is it resonant type or turbulent and laminar?
@jacquespoirier9071 Жыл бұрын
these chambered mufflers are all based on the Helmholtz tube development, it is very delicate to taylor the sound the muffler will produce. there is engineers that spend their carrers tuning mufflers for automotive industry so it is a very good idea to use an original muffler specific to a vehicule to duplicate a home made muffler to avoid indesirable effects as droning.
@user-ew3fv9yp7w19 күн бұрын
Даусы қалай болды екен???
@amerikanstafford Жыл бұрын
Ok good job.But which side is the entrance and which is the exit??? If it is not connected correctly, the gases will stick to each other.
@GPGarage1 Жыл бұрын
Thanks. It does not matter which pipe will be the inlet and which the outlet, the flow of exhaust gases remains the same.
@amerikanstafford Жыл бұрын
@@GPGarage1 Ok.
@EmanuelFilms Жыл бұрын
what thickness is the stainless steel plate at the start of the video?
@GPGarage1 Жыл бұрын
It's 2mm
@EmanuelFilms Жыл бұрын
@@GPGarage1 thanks for replying. Looks tough to get the stainless sheet to wrap around the muffler but I think I’ll try it. I’m thinking of making a muffler for an e46 m54b25. Have you made one for that engine? Do you have any tips or maybe best way to make the inside for nice sound? I was thinking of doing a perforated pipe inside and the rest empty but I think it might drone at low rpms
@GPGarage1 Жыл бұрын
@@EmanuelFilms For the muffler, You don't need a thicker sheet than 1-1.2 mm, I worked with 2 mm because I had one. I'm not on the m54, I made it for the m52tub25 and if you're going to leave the middle resonator, then you can make the rear stright-through muffler, perforated tube with glass wool.
@EmanuelFilms Жыл бұрын
@@GPGarage1 thanks. Yes the plan is to only change the rear muffler. See what it’s like, then do other changes if it needs to be changed