thank you sir :)

Thank you sir

Salamat sir

Salamat sir 🙂

Thank you sir

Thank you sir

kaya mo yan sir.... ako din nag-try lang :)

@@jessambrosio1848 salamat sir ng paplano din po mg gawa nyan ipun muna mg pambili heheh slamat godbless

baka tulog yung BMS ng battery bank mo kaya di mag-charge. Tama,, try mo direct konek sa battery ang SCC para ma-charge sya tapos gamitan mo tester para check voltage with and without BMS

madaming way para makagawa ka ng 8s20p. ang bilhin mong 32650 na cell ay yung may nut sa isang side at screw sa kabila para madali mag-assemble ng patayo (magkapatong). kung sa similar ng setup ko, need mo lang doblehin ang column ng positive/negative ng series connect bale ++ - - ++ - - ++ - - ++ --, 8s2p na yan so ulitin mo lang ng 10x yan para makagawa ka ng 8s20p

yes sir, maliit na ring terminal lug

battery wise kaya nya pero yung itatagal (oras) varies kung ilan watts yung rice cooker. Ang pinaka-importante yung inverter mo dapat nasa 3kw (recommended) kasi parang AC na rin yan rice cooker sa power requirements

Depende ano voltage ng battery gusto mo build (ex. 12v or 24v). Kung 12v, you need at least 4 cells ng battery na may 3.2v each (3.2 x 4 = 12.8). Yung BMS depende sa voltage at total ampere ng battery build mo.

Pagka alam ko mode 1 ang grid priority ng snadi pero wala kasi akong snadi kaya di ko sure. Try mo search sa youtube.

quick answer is yes but you need to have BMS for each battery pack and make sure state of charge (SOC) is same before connecting in series. Alternatively, you can build single 48v battery pack. Warning - 48volt is dangerous enough to cause injury so make sure you know what you are doing.

If each 32650/32700 cell is 3.2v, you will need minimum 16 cells to make a 48v battery pack with 6ah. So the total number of cells will depend on the ampere hour of the battery pack you want to build. For example, to build 100ah 48v battery, you need to parallel 17 pcs of 6ah cells to get 102ah then you need total of 272 cells ( 17p x 16s = 272 ). Hope this helps

Ano specs ng bawat cells sir? Total AH ay depende kung ilan volt (12v or 24v) gusto mo i build na battery bank

Pag series connection ay add mo voltage ng bawat cells at kapag parallel connection ay yung ampere ng bawat cells ang I~add . Yung 32650 battery cell gamit ko ay rated 3.2v at 6ah bawat Isa. 8S12P yung battery pack na ginawa ko ibig sabihin 8 cells in series for toral of 25.6volt (8x3.2) at 12 cells na parallel which equals 72ah (12 x 6ah)

Depende yun itatagal sa inabot ng SOC ng battery mo during charging regardless kung mppt or pwm SCC mo OR kung AC charger ginamit. Another factor ay kung brand new cells battery mo or used cells

12 rows na 8 cells bale 96 cells lahat

check mo total watts ng magiging load mo divide mo sa nominal voltage ng battery bank mo. For example, 1000 watts load divided by 25.6v = 40a and bms need mo

yes sir

@@jessambrosio1848 paano po gawin ang top balancing, newbie po. salamat

@@allanmaninang1033 i-parallel connect mo lang lahat ng cells. meaning, all positive together at all negative together tapos need mo ng charger to charge the pack at 3.6volt

@@jessambrosio1848 maraming salamat po sa reply sir.

Output ng inverter ay either 110v or 220v AC, sa atin sa Pinas ay 220v AC. Trabaho ng inverter i-convert ang 12v or 24v DC sa 220v AC, automatic yun kaya pede mo gamitin mga appliances sa bahay basta may inverter ka. BTW, 2 klase inverter yung PSW (pure sine wave) at modified sine wave. Make sure PSW yung gagamitin mo

@@jessambrosio1848 maraming slamat sir

1 x 2p at 1 x 1p tabbing wires na 5meters each. may sobra pa

Wala sir

double check mo yung positive at negative connection dapat match sa SCC papunta MCB papuna battery

Good day sir. Paki tingnan po yung previous comment bago kayo sir same yung taniong at nandun na sagot

watch this link for my solar panel setup - kzfaq.info/get/bejne/ndeZd8h4mLORqoE.html

May BMS ba yung battery bank mo? Importante yun para di ma-overcharge at ma-over discharge ang battery para tumagal

@@jessambrosio1848 opo sir Meron po

@@websprove may bluetooth ba BMS mo para makita mo yung status ng mga cells kung balance sila or meron malaki difference? BTW, nag balance ka ba ng voltage ng mga cells bago assemble yung battery bank? double check mo din configuration ng BMS mo kung tama. last resort ay kalasin mo muna tapos isa isa mong check bawat cells kung okay pa voltage baka meron dead na or super low volt

kung 100w load mo kaya nito continuous use at least 12hours. gamit ko electric fan 51w magdamagan 10-11hrs ay meron pa din sya SOC na 25.8v paggising ko ng umaga basta fully charge yun bat prior to use. depende sa watts ng fridge mo itatagal ng battery

@@jessambrosio1848 salamat sir,.. Tanong kopo ulit sir pwde Po Ako gawa Ng additional battery pack? Same voltage at ampere sa dalawang battery pack? Then e parallel ko Silang dalawa? At naka bms nadin Sila? Safe Po ba sir?

pede pero magastos yan kasi need mo BMS for each pack. Mas okay, gawa ka ng 200ah sa isang battery pack para isang BMS lang need mo at mas simple ang setup

@@jessambrosio1848 cge sir salamat po sa tips.

Hindi sya hybrid

Pag po lalagyan ng solar panels mag add din ng scc dahil ndi hybrid ne boz, pero if hybrid inverter gagana po ba kahit walang solar panels? Newbie lang po, interested mag assemble ng wala muna panels as stand by like yours boz

Sa panahon ng tag ulan di kaya. At least 200ah para kaya tumakbo ng 1 to 2 days na makulimlim panahon

Ilang PCs Ng 32650 yong pinakita mo sir

100pcs yung nasa box pero 96pcs lang nagamit para sa 8s12p battery pack

​@@jessambrosio1848ilang Watts PV pwde i charge sir

you can build better quality battery pack yourself for your scooter :)

sa ngayon efan lang gamit ko sa kanya overnight daily. you can watch this video when i used it for my solar generator kzfaq.info/get/bejne/aapoaM93vNrViqs.html

Sir Kung Maka buo po kayo ng 200Ah 24volt ilang amperahi na BMS pweding ilagay,?

Need mo mag-dagdag additional 3 rows of 8 cells. bale 3x8 = 24 cells pa needed para maging 100ah

@@jessambrosio1848 salamat po ng marami sir

sorry sir magiging 90ah lang pala kung 3 rows lang dagdag mo. need mo 5 rows bale 40 cells pa need mo (5x8) para maging 102ah

@@jessambrosio1848 ok po sir

25mm yung size ng wire

@@jessambrosio1848 thank you por same kc tayo ng set up boss 8s 12p. ilang kw yung inverter mo boss?

@@ruscon_isola 1000 watts

Ano load mo jan boss sa batt mo pag gabi ina abot ba ng umaga?

@@drawingtravellers9872 di ko po na try gamitin sa gabi kasi backup power ko lang ito. minsan ginagamit ko during daytime at kaya i-power sabay-sabay ang 55" LED TV + electric fan + gaming laptop 15" + 24 inch LED monitor running for 6 hours with still 40% battery charge left. Total load ranging from 150-170watts

Thank you for your interest sir but for now busy pa po kaya not able to accept DIY orders po

sa lazada sir. ito yung link www.lazada.com.ph/products/i2466936840-s11285438535.html?urlFlag=true&mp=1&spm=spm%3Da2o4l.order_details.item_title.1

Total nagastos ay nasa P10k lahat more or less

8 cells po naka-series bawat row (horizontal) at 12 cells po naka-parallel bawat column (vertical)

parang letter S lang po yun connection from bottom to top. pansinin po ninyo diagram makikita ninyo alternate yung top at bottom sa tabbing wire

@@jessambrosio1848 cge sir pagaralan ko Po maraming salamat po

Need nyo po 264 cells na 6ah each para makabuo po kayo ng 8s33p which will be 24v 198ah battery pack

Approximately P18k sa battery pack. Yung inverer nasa P6k ata bili ko. Pede naman i-charge ito directly sa outlet basta may battery charger ka na 24v output

@@jessambrosio1848 maraming salamat po sir

Wala pong charger ang mismong inverter kya need bumili ng separate 24v charger para po s battery?

@@sthielldizon2042 may built in AC charger po yung torroidal one solar inverter na gamit ko kaya pede din charge using the inverter

Salamat po 😊 May nkita po ako n hybrid n one solar, 24v 3000w, pwd din cia kahit walang panel sir Salamat po uli

thanks for the interest pero for my own use po ito :)

Check mo voltage ng battery baka lowbat sya. Kung low bat ay charge mo muna bypassing the BMS. Meaning konek mo diretso sa main positive at main negative at bantayan mo maging 25v saka mo ulitin ang method sa pag activate ng BMS

@@jessambrosio1848 ok Po sir copy, Tanong ko din sir di Po ba dapat Ang wiring Ng bms sa battery dapat din Po ba e follow or eh online Ang wiring? Baka Kasi may Mali sa wiring ko Po sa aking bms to battery.

I mean e next next Ang wire di Po dapat Kahit saan makalagay Po Ang wire?

to check BMS balancing wire if connected properly ay disconnect mo muna yung actual BMS sa wire nya. Tapos check mo voltage ng bawat pin sa white connector ng balancing wire kung nasaan yung 8 red wires at 1 black wire na manipis. Gaya ng ginawa ko sa video

Kung voltage ng battery mo (direct connection) ay 24v pataas, ay possible nga na may mali sa BMS wiring mo

8S12P means 8 cells in series and 12 cells in parallel. For series connection, you will add the voltage of each battery cells. so for 3.2v 6ah battery cell, that is 3.2v x 8 = 25.6v (which falls under 24v). For parallel connection you will add the ampere of each battery cells so 12p means 12 x 6ah = 72ah battery capacity. Series connection means yung positive ng 1st cell you will connect to negative of next cell and so on (basta alternate ang +/-). Parallel connection means all positive terminals of the battery are connected together. The same for negative terminals.

32650 lifepo4 cells sir (pede din 32700) na 3.2v 6ah each

Sir kung mag add po aku ng cells 6row pra makuha 100+ah anu po tawag maging 8s18p ganon ba sir still 24v prin.salamat po sir...godbles po.

D na poba need sir lagyan ng AB?

tama po 8s18p means nag-add kayo ng 6 more rows na 8 cells each pero need mo lang 8s17p para maging 102ah yung battery pack

optional po AB but good to have if you have the budget

wala akong nilagay AB sir

thank you for your interest but not accepting orders for now

96 pcs sir

Nasa video sir yung arrangement ng mga cells

Need nyo sir ng additional 32 cells na 6ah each grouped in 8s4p to be added sa existing 24v 72ah na ginawa ko. bale 4 additional rows yun sa bottom na meron 8 cells per row. Magiging total capacity nyan ay 24v 96ah.

@@jessambrosio1848 how about sir if magadd nalng Ako Ng additional 16pcs. Na battery with the same 8s12p pra maging 84ah nalng cguro pwde Po ba Yun? Salamat po

pede sir pero magiging 8s14p na yung setup dahil may additional 2 rows ka ng cells

@@jessambrosio1848 yes sir Tama Po kau magiging. 8s14p

@@jessambrosio1848 Tanong lang sir matagal Po ba malowbat or ma drain Ang ganyang setup compare sa gel type Po na battery?

noted on this request sir

approximately 18k pesos para sa materials ng battery pack

@@jessambrosio1848 Thank you

Sa lazada sir www.lazada.com.ph/products/i2466936840-s11285438535.html?urlFlag=true&mp=1&spm=spm%3Da2o4l.order_details.item_title.1

@@jessambrosio1848 ty boss..

Sa last part ng video near the end ni explain ko dun paano i-activate ang tulog na BMS using inverter with built-in AC charger

OK PO SIR, THANK U, KEEPSAFE

OK PO SIR, THANK U, KEEPSAFE

Nasa P18k sir lahat lahat

yes sir, going forward, will try my best to have english subtitles in my future videos :)

Dapat ay equal or higher ang BMS sa battery capacity

Powerpoint lang sir

Wala sir

@@jessambrosio1848 ok nmn ba sir ala nmn problema?

okay naman at meron passive balancer yung BMS ko at before assembly ay ni-balance ko yung mga cells kaya di gaano magkakalayo voltage nila

@@jessambrosio1848 ok po sir maraming slamat po