DIY Bluetooth Speaker Using Pallet Wood V2

No video

DIY Bluetooth Speaker Using Pallet Wood V2

Рет қаралды 1,745,054

Күн бұрын

*Materials in video
- Creality Cr10 - V2 3D Printer Machine: www.creality.c...
- Wifi & Bluetooth 5.0 Board Up2stream Amp V2:
+ Link buy in aliexpress: tiny.cc/czuksz
+ Link buy in arylic store: www.arylic.com...
- 5.25inch 4ohm 40W Woofer Speaker: tiny.cc/ixuksz
- 2.5inch 4Ohm 15W Full Range Speaker: tiny.cc/gxuksz
- 2inch 4Ohm 20W Tweeter Speaker: tiny.cc/frbjtz
- 4 Way Crossover Board: tiny.cc/mxuksz
- Makita Terminal: tiny.cc/oxuksz
- 3 Pin On/Off Switch: tiny.cc/xxuksz
- Remote for amplifier board: tiny.cc/ryuksz
- 24V 4.16A Power Supply: tiny.cc/2zuksz
- Leather Handled for speaker: tiny.cc/pzuksz
- Speaker single face seal glue: tiny.cc/40vksz
- 5.5 DC female jack: tiny.cc/g0vksz
- LM2596 Step down module converter: tiny.cc/u0vksz
- Acoustic Foam: tiny.cc/h1vksz
- Pocket Plasma Disk: tiny.cc/qrbjtz
- Pillars PCB Board Nut Screws: tiny.cc/fpllsz
- Insert Nut Blind Hole Single Pass Copper: tiny.cc/fpllsz
- M3 x 5mm Screw : tiny.cc/rpllsz
- Anti Shock Rubber Stand: tiny.cc/wpllsz
- Electrical crimp terminal for connector wire: tiny.cc/0qllsz
* Watch more video
- Portable Projector Bluetooth Speaker Build: tiny.cc/ov5iuz
- Epoxy Inlay Dovetails Bluetooth Speaker Build: tiny.cc/qv5iuz
- Pallet Bluetooth Speaker V3 DIY: tiny.cc/pv5iuz
- Epoxy Dovetail Joint Bluetooth Speaker DIY: tiny.cc/uv5iuz
- DIY Bluetooth Speaker Using Pallet Wood V2: tiny.cc/0h7nsz
- Upgrade Bluetooth Speaker Using Broken Skateboards: tiny.cc/vg7nsz
- DIY Bluetooth Speaker Using Broken Skateboards: tiny.cc/5fxhpz
- DIY Bluetooth Speaker Using Pallet Wood: tiny.cc/mhmzmz
- How To Make A Wifi - Bluetooth Speaker: bit.ly/34IjlLH
- How to Turn Old TV into 4.1 Bluetooth Speaker: bit.ly/2pCrSkA
- Colored Pencils Bluetooth Speaker V2: bit.ly/2P1PWHY
- DIY Epoxy Resin Bluetooth Speaker: bit.ly/2miziaZ
- DIY subwoofer: bit.ly/2PaKYu4
- DIY 2.1 Bluetooth Speaker Using Colored Pencils: bit.ly/2IlnoEo
- DIY Bluetooth & Wifi Speaker: bit.ly/2GoP5va
- DIY Buetooth Speaker: goo.gl/UzrZRR
- How To Make A Waterproof Bluetooth Speaker Using Plastic Pipe And Simple Tools: goo.gl/RdUL2T
- DIY 2.1 Bluetooth Speaker Using 100W Subwoofer:
goo.gl/i1pPUY
- How To Make Boombox Bluetooth Speaker Using Pipe Plastic (New Version): goo.gl/tExBri
- How To Make Boombox Bluetooth Speaker From Pipe Plastic:
goo.gl/8y3VSx
- Building Portable Bluetooth Speaker goo.gl/nMKukP
- How To Make A BoomBox Bluetooth Speaker goo.gl/t8zYjD
- How To Make A Solar Power Bank Charger For Mobile:goo.gl/K7s9Hg
- Diy Bluetooth Speaker From Box Tea: goo.gl/DUSj8x
- How to make 24V RECHARGEABLE BATTERY: goo.gl/BTbzp6
- How to make 3s Battery: goo.gl/oL2cfM
- DIY Cooling Fan For Laptop: goo.gl/z3SRtR
* My Page In Facebook: bit.ly/33TEyTC
* Join My Group In Facebook: goo.gl/BMvRAj
* Help Me Reach 500k Subscribe Here: goo.gl/dXJRte
#palletspeaker
#palletbluetoothspeaker
#kingminhvuong

Пікірлер: 970

@KingMinhvuong 4 жыл бұрын

Hi Friends! Do you like this speaker?

@slicksport2000 4 жыл бұрын

That is quite a speaker man. Nice full sound. Looks solid. Love your work 👍

@arwannur 4 жыл бұрын

Support my chanel boss

@n.and.official5747 4 жыл бұрын

I am always waiting for your latest videos and that is enough to inspire me to make

@dnca97 4 жыл бұрын

Speaker 300000$

@mateusvictor7934 4 жыл бұрын

AWESOME MAN!!! what a fantastic work... congratulations! keep doing it !

@truetrue8351 3 жыл бұрын

I am Korean. I've never seen this before. I was surprised. You're so dexterous. I'm touched. I started subscribing. I'm looking forward to the new video.

@lyteyearz5810 4 жыл бұрын

I am THOROUGHLY and I do mean THOROUGHLY impressed. This is easily in my top 10 wood repurposing videos. Wish I could sub twice!

@KingMinhvuong 4 жыл бұрын

Thank you!

@jpeg4113 4 жыл бұрын

Make a second account I dare you 🤣

@lyteyearz5810 4 жыл бұрын

@@KingMinhvuong Absolutely

@lyteyearz5810 4 жыл бұрын

@@jpeg4113 Lol 😆

@BigTCars 3 жыл бұрын

As someone who is good at fixing things, but no building them from scratch. I learned so much from watching this. I hope you will make a version 3 and improve upon it again! I love this sort of video. I get to see how different people approach the same challenges. Your approach to drilling the holes was different then what I've seen other craftsman do, for example. Thank you for sharing your skill.

@matthiasmartin1975 3 жыл бұрын

This is extremely well done. You have quite a reare combination of taste, wood working skills and sufficient electronics skills to pull this off. I especially love how you treated the wood with oil and stayed away from laquer.

@fitrisadha95 3 жыл бұрын

Can Tex

@StaticVapour590 4 жыл бұрын

I like this, very creative way to reuse wood that is just lying around PS: Don't care about those haters, it's your hobby, your way to build speakers and they are unique

@KingMinhvuong 4 жыл бұрын

I like your comment. Thank you so much!

@StaticVapour590 4 жыл бұрын

@@KingMinhvuong Thank you for making videos!

@profharveyherrera 3 жыл бұрын

I enjoyed every minute of this video. I've seen other boombox builds but what is really outstanding about yours is the attention to detail in the inside equal to the outside. Cheers!

@paras5567 4 жыл бұрын

Probably the best diy bluetooth speaker ever made 💯

@SgtKingUSMC 4 жыл бұрын

This is a super clean and good listing of parts used. For others to follow. Job well done.

@KingMinhvuong 4 жыл бұрын

Thank so much!

@whatsappme--1692 4 жыл бұрын

Am i the only one that loves watching how the nails were removed?😂

@davidbell9143 3 жыл бұрын

I was suprised that he used such a small hammer for the job.

@xxg.tester7851 3 жыл бұрын

Nope

@Bodari23 4 жыл бұрын

This is the Perfect Speaker Cleanest made I have ever seen 👍🏼

@KingMinhvuong 4 жыл бұрын

Thank you

@IanTheWoodchuck 3 жыл бұрын

Excellent design and choices. I like that you use the air movement of the bass port to help cool the DC/DC step-down. I have only two VERY minor suggestions... First, use a less obvious plastic for the 3D printed parts like a stainable woodPLA. It's such a pretty piece and the neon green is distracting. The second suggestion is that I feel like the Bluetooth receiver seems unprotected. Some sort of hard plastic shield over it would be preferable to it being exposed, plus it looks a little out of place. I'd love to have something like this myself, and I appreciate you using the Makita battery as opposed to trying to hack together your own solution. I use Ryobi tools myself and having a common battery platform is invaluable!

@yssing 3 жыл бұрын

I love building stuff from old pallets.. This speaker looks really good.

@richardalmario2199 3 жыл бұрын

When i watch this. I verry a maze until end amazing skill..I really love all a lot of tools.. hehe clean job keep it up bro..

@fumez9877 3 жыл бұрын

Did not even realised that 38 min were up. Mate, i thank you for sharing your imagination and skills with us !

@KingMinhvuong 3 жыл бұрын

Thank you!

@massimilianodotto2891 4 жыл бұрын

Congratulations, great project, well done with excellent electronic components. Difficult to make such accurate details for those who do not have professional machinery. Questionable the choice to put the IR sensor and LED. The choice of placing the drill batteries externally is wonderful. It was very nice to see the video, and I will steal your ideas for future projects. Compliments

@KingMinhvuong 4 жыл бұрын

Thank a lot sir. Good luck to you!

@playertwo9903 3 жыл бұрын

I love your videos! You have a real talent that might pass under the radar sometimes but it's as precious as any! Keep up the great work, you're inspiring me!

@nikolastojsavljevic5469 4 жыл бұрын

My friend this is another level!!!! Fabulous and clever design

@KingMinhvuong 4 жыл бұрын

Thank you!

@bobalex6323 3 жыл бұрын

I liked the organic design and the clever idea of using the drill battery.

@vlogmyworld1790 4 жыл бұрын

Hay quá, giỏi quá. Dân công nghệ thông tin, biết điện tử, thích làm mộc, mê âm thanh, thích chế tạo(in 3D) trong một 😄. Chắc còn nhiều môn nữa mà chưa show hết. 😁

@HarmonicaMustang 4 жыл бұрын

Looks good, but I don't envy whoever sets about replacing the drivers. When I repaired my speakers I silently blessed whoever decided to use crimp connectors and leave plenty of cable slack.

@stopthephilosophicalzombie9017 3 жыл бұрын

The drivers will last a long time. Not really something to worry about.

@charlesreid9337 3 жыл бұрын

@@stopthephilosophicalzombie9017 people are still repurposing speakers from the 60's.... your thought process is the problem

@charlesreid9337 3 жыл бұрын

i cant stand people who do that "well we have to save .001 cents in wire to have it look cool inside a box that will ONLY ever be opened by someone working on it so.. fuck them but theyll think its neat".. no dude theyll think youre an asshole

@Filippoupolitis 4 жыл бұрын

Man I just have to say amazing job. U seem like a very creative person always trying for the best results. You deserve the views and money you get. Keep it up!!

@KingMinhvuong 4 жыл бұрын

Thank you!

@jekakornichenko9757 3 жыл бұрын

@@KingMinhvuong your projects so cool, thx you!

@paulgreene9997 3 жыл бұрын

I like your technique for pulling nails - it prevents a lot of wood from getting mangled.

@KingMinhvuong 3 жыл бұрын

Thank you!

@MC_AU 4 жыл бұрын

Craft & Mechanical 100% Electrical 85% Acoustic 60% Really nicely done, but the whole point is to get great sound without intermodulation between left & right. V2.0 ?

@lyteyearz5810 4 жыл бұрын

Can you elaborate on that please? I will be using my learning ears...well eyes but you get it lol. Anywho, just want to be the student for your reply.

@MC_AU 4 жыл бұрын

LYTE Yearz without thinking too hard, two issues come to mind. Separate the sealed volume for left & right channels. Is the internal volume correct for the drivers being used? The reflex tube needs to be tuned & duplicated for each channel. You can probably skate a thin line between calculated perfection and decent sound... The rigid box is a good start if the resonances and tuning are close to a harmonic of the drivers. I’d buy one if it went the extra distance! *Question*... How good is the response and audio performance of bluetooth in general?

@lyteyearz5810 4 жыл бұрын

@@MC_AU excellent reply. At work right now. Going to need to absorb this on lunch break though!

@HoloScope 4 жыл бұрын

@@lyteyearz5810 get back to work silly billy! sike im at work too

@admahecha 4 жыл бұрын

I love the repurposed of the materials

@wadahalmatar6068 4 жыл бұрын

very good job, Amazed how clean work that was 👍🙏

@vuxuanthokc 3 жыл бұрын

Lần đầu xem video của bạn nghĩ của thợ nước ngoài làm (thợ ÂU nhé) rất cẩn thận và chuyên nghiệp. Bạn đã thay đổi cách nhìn về thợ VN. Rất rất chuyên nghiệp, chúc bạn ngày càng phát triển kênh của mình. Và thợ VN cần hướng tư duy làm giống như cách bạn làm

@chriscarri 4 жыл бұрын

If not the best diy speaker one of the best in youtube

@maksatzhankulov7886 4 жыл бұрын

Это просто шедевр! Нет слов

@jekakornichenko9757 3 жыл бұрын

Не то что другие

@chinomsomaduagwu8415 4 жыл бұрын

This is Amazing work, I'm supper impressed. Weldone

@KingMinhvuong 4 жыл бұрын

Thank you!

@kingswagg3452 3 жыл бұрын

Amazing job gorgeous build for the next version I think it would be better to isolate the sub woofers instead of the full range speakers

@KeepCalmAndCarryOn1110 4 жыл бұрын

Làm một cái hộc bên trong loa để gài pin thì hoàn hảo về thẩm mĩ. Có lẽ là bên trong đã hết chỗ trống. Nói chung càng lúc càng thích kênh này! 👍👍

@matimad0338 4 жыл бұрын

When i can't sleep i watch that Stuff

@oussamaboucenna3455 4 жыл бұрын

me too 😅😅😅

@FlexxoMaticify 4 жыл бұрын

Me too

@KingMinhvuong 4 жыл бұрын

I think you'll sleep even better if you watch my video. jok :D

@WietseStarsz 3 жыл бұрын

Same

@abhijithappus3401 3 жыл бұрын

I respect you. People who make fun of you and caption you are incapable of recognizing your potential. I often watch your videos sleep deprived. I love the cleanliness of your work. Love you sir ❤️❤️❤️❤️ from india

@juliofranco9143 4 жыл бұрын

👏👍from Brazil - State Minas Gerais

@KingMinhvuong 4 жыл бұрын

Thank you!

@memoortega3973 3 жыл бұрын

Extraordinario trabajo.... Felicidades!!! Y esa impresora 3D esta de lujo!!!

@BillyKueekSG 3 жыл бұрын

You are brilliant! Everything is thoughtfully done and very tidy cables arrangements. Best part, you made this from a pallet. I can only “screw “ things up so I really admire your skills.

@BargainSavage 4 жыл бұрын

Great looking build I love these homemade stereos.

@KingMinhvuong 4 жыл бұрын

Thank you!

@suvidkitke9552 4 жыл бұрын

Legend says he's still making..

@AsyrafAkira 4 жыл бұрын

Just some suggestion to put some sort of screen over pipe. Just to prevent insect from making home inside the speaker.

@strugglingparodox5709 3 жыл бұрын

Just WOW! The patience it takes to cut out all those structor ribs.

@KingMinhvuong 3 жыл бұрын

Thank you!

@TachirosLament 3 жыл бұрын

not sure who needs to hear this, but playing "no one knows" by Queens of the Stone Age goes great with this video apparently.

@alekseialekseev2480 4 жыл бұрын

Очень классно...

@SurachetSendaeng 3 жыл бұрын

Really like every minute that you had spent on the speaker ... really amazing.

@cracaf4118 3 жыл бұрын

めっちゃかっこいいですね！いつか自分でも電子部品まで組み込んでみたいです。

@jimmyzez4359 4 жыл бұрын

Amazing it sounds just like my internal PC speaker.

@crazyclips884 3 жыл бұрын

DYI Really, Are you serious?? No one owns these thousand dollars machine at home.

@jagsfanrick 3 жыл бұрын

Exactly, niche thing too.

@EugenioFructuoso 3 жыл бұрын

you can do it without this machines, only take more work and care

@michaelfl68 3 жыл бұрын

So talented.. so many creative and beautiful things can be done with recycled wood. Thanks for sharing

@naadcomp 3 жыл бұрын

Beautiful craftsmanship

@kexx99 4 жыл бұрын

25 гдн 3-4 надо было поставить, тогда было бы гуд.

@user-ks8bq6ig2v 3 жыл бұрын

Ему сзади не помешало бы пару хороших пассивных резонатора, ато бас не ахти. У меня малюсенькая Nomi с одним большим резонатором звучит гораздо лучше.

@tianharvan 3 жыл бұрын

It's great .But not realy DIY .The stuff this Guy has .Did you see the printer wauw .

@mythcrab6047 3 жыл бұрын

This is DIY. DIY does not mean using only your hands.

@tianharvan 3 жыл бұрын

@@mythcrab6047 Your so right . I said it wrong .

@tianharvan 3 жыл бұрын

@@6moon.s English is not my native language..And I said I was wrong ! I like what this man does .And why am I Lazy ? Why so hostile .Have a good day .

@alexanderredler862 4 жыл бұрын

This was an awesome build. Probably your best and most informative yet. Right before you showed the wiring diagram, I thought to myself "Damn that looks complicated, hope he has a diagram somewhere!"

@ThPappas 3 жыл бұрын

You are right,it is the best of all of his builds.

@flaggedowntown 2 жыл бұрын

Good instruction, well laid out design, loved the use of a tool battery. About the only question I had was tuning the box volume & port tube to the chosen drivers. I've watched a few of your videos & subscribed after seeing this build.

@KingMinhvuong 2 жыл бұрын

Thank you so much!

@jhordanmeneses6170 4 жыл бұрын

me: doing this everynight.. In my dreams! lol

@user-nc3su7kw1d 3 жыл бұрын

Бои,без правил.

@1bandit342 4 жыл бұрын

Без станков хрен бы ты что сделал

@kexx99 4 жыл бұрын

Я думаю, что без станков ни кто за такое не взялся бы.

@bormanNjoy 4 жыл бұрын

ОК тогда это не DIY, а практически промышленное производство.

@thien8artdesign 4 жыл бұрын

Closed speaker technology is how to divide the sound wall between the speakers so that the new sound is good. Your speaker is only bulky in size but does not sound good. You are missing this.

@omotolaoyeniyi631 4 жыл бұрын

Upgrade your ear phones or multimedia speakers maybe you will hear the real sound from this

@johnlane2395 4 жыл бұрын

@@omotolaoyeniyi631 my system is 10,000 easy, the mic sucks, can not tell the fidelity without the right mic, surprisingly not all pallet wood is bad, sometimes they do not know what they can get, there has been Mahogany pallets I have used

@ReoFies14841 3 жыл бұрын

Tío eres un crac , y me das una envidia grande, eso si, envidia sana. De ver las herramientas de trabajo casi nuevas con las que trabajas que con ese equipo puedes realizar casi cualquier cosa te propongas. 10 de 10 puntos te doy .

@glenndunlop9949 3 жыл бұрын

Very Clever the addition of the Cordless Drill Battery!........The reality is there is thousands of dollars of tools and machines here to build one of these and those components (speakers, crossover units bluetooth modules etc ) that were used are starting to get "up there" in terms of price...Dont get me wrong very impressive build....BUT expensive to build for a home handyman...even if he had half of those tools 3D printers are NOT exactly cheap to buy...and IF you find a CHEAP one it wont last...and the wood planer/thicknesser are NOT cheap either.....as once you ADD ALL the tools and components prices together better to buy a JBL Boombox for about $500 NZ ......but very nice build!!

@paullewis1637 3 жыл бұрын

Lot of work went into that, but brilliant outcome, well done.

@MrBrymstond 4 жыл бұрын

This was worth every minute, awesome! I love the build and I have a bunch of those Arylic amps. One thing is the crossovers make a world of difference if you match them to your speakers. I love the idea of using a power tool battery too, they have a high output. Free pallet wood is a great idea as I can get pallets made from hardwood like new.

@KingMinhvuong 4 жыл бұрын

Thank you!

@GabrielKTX 4 жыл бұрын

Este video merece más likes!! Te felicito por la dedicación que le pusiste al proyecto!

@apusista 3 жыл бұрын

This is the BEST one I have seen so far! Amazing!! TO START WITH THAT CRATEWOOD... Ufffff! Too good! Humbling... truly!

@muhammadikhsan1639 4 жыл бұрын

very steady requires a long process and high creativity, enthusiasm continues

@toshirouzumaki777 3 жыл бұрын

BEST ACOUSTIC ! And beatiful ! It's a dream..

@TommyMcDermott 4 жыл бұрын

So beautiful and so much detail and effort put into it. I still can't believe the wood transformed. Well done 😀

@KingMinhvuong 4 жыл бұрын

Thank you!

@Poccu9IHuH 2 жыл бұрын

One thing is definitely wrong is drivers compatibility. Woofers must be bigger, deep coned, so more powerful and split volumed to complete right frequency spectrum (flat) and adequate power. Splitting volumes with sub drivers will not affect mid drivers and tweeters to run properly. So your setup has focus in midbase and highs. Lows aren't pronounced. Or mids are useless in this setup. But the work done is definitely amazing! My applauses! 👏👏👏

@KingMinhvuong 2 жыл бұрын

Thank so much for your comment!

@cintajayaservice7464 3 жыл бұрын

steady creative, worthy of example

@spenny3403 3 жыл бұрын

That turned out awesome dude! Wish I had a Woodshop setup to be able to do something like this oh, very cool! I'll bet it sounds amazing with all the acoustic dampening and bassport.

@mukniahmamben6867 3 жыл бұрын

Iphf

@silentrobcanada 3 жыл бұрын

Amazing video. I did laugh when you painted the PVC black instead of just buying ABS which usually comes black.

@KingMinhvuong 3 жыл бұрын

I don’t find black pipe! Thank you

@PS3TEKKENLORD 3 жыл бұрын

JUST TO GET AN IDEA HOW MUCH WOULD THIS COST TO PURCHASE A SPEAKER LIKE THIS ONE ON THE MARKET??? BTW AWESOME BUILD!!!!

@KingMinhvuong 3 жыл бұрын

Thank you!

@sexraja 4 жыл бұрын

Appreciate your efforts to build such an unique speaker

@rongeernaert1208 3 жыл бұрын

Superb Bluetooth speaker DIY from palletwood !

@KingMinhvuong 3 жыл бұрын

Thank you!

@w7class 3 жыл бұрын

I don't even dare to imagine of what the price of such a custom speaker would be!

@eclypes2008 3 жыл бұрын

finally someone that knows how to use a table saw right

@Lockgistan2023 4 жыл бұрын

nice build.. well planed and nice wood skills and cable management skills u got there...

@UlyssesDrax 3 ай бұрын

After all that incredible work building a beautiful speaker box, you left those 3D printed parts on the outside green! Why did you do that? You should have painted them black for consistency and uniformity.

@kakafoods-chuyenthucphamnh2466 3 жыл бұрын

Nhìn cái thùng là ghiền. Bác nên làm số lượng nhiều để bán ra khắp VN và xuất đi TG. Loa rất đẹp

@PopaAlexandru. 4 жыл бұрын

Good achievement. How long will the glueings last? Box completely closed before commissioning? The IR sensor is predestined to be hit ... Dual power is a good idea.

@LoftechUK 4 жыл бұрын

Dude. Your so good with wood

@TheSpotify95 4 жыл бұрын

This is a pretty good speaker! Very high quality design, good quality components, this is the best one that you've made on the channel so far :) and the battery is modular as well - good if you have anything that connects via a Makita drill battery connection :)

@KingMinhvuong 4 жыл бұрын

Thank so much!

@letmindcreative 4 жыл бұрын

Nice video love and support from India 😊

@Jeanpierredlt 3 жыл бұрын

That speaker with light that looks like rays was totally unreasonable and and not with one at all friend, greetings from the

@Leemond03 3 жыл бұрын

Very brilliantly made, love watching videos, do you make them to buy, would be a good addition sat outside on warmer nights. I admire your creativity. Thankyou for such a video, warm regards

@MrStevedore1 4 жыл бұрын

Incredible skills as usual. And the tools are quite an investment. Nice job as usual...

@mazhartahir5810 3 жыл бұрын

i also make speakers but your work so satisfying clean. well done!

@TheGrabbers 4 жыл бұрын

Мужик Ты крут!!!

@Tman0517 4 жыл бұрын

This with a basic no disc car radio would be pretty badass

@dropday1989 3 жыл бұрын

We missed this!

@RampoRio2017 3 жыл бұрын

nhà bác này nhiều dụng cụ chiến quá he... Sắm đống đó chắc bộn tiền đây, có bị vợ nhằn chưa ... he he he

@adigal209 4 жыл бұрын

One of the most Alegent and extremely detailed diy speaker video, and in general diy video

@KingMinhvuong 4 жыл бұрын

Thank you!

@SelectedPeppa 4 жыл бұрын

Nice project. I wonder how much the components heat up inside. Wood is not the best heat conductor and there is no airflow...

@Killasaull 3 жыл бұрын

Beautiful job, nicely done. I would concider speaker covers.

@KingMinhvuong 3 жыл бұрын

Thank you!

@lamhuynh6997 3 жыл бұрын

Có bán ko bạn

@joselu90 4 жыл бұрын

Very nice work!

@RA666ful 3 жыл бұрын

Хоть и длинное видео, но было интересно смотреть, ничего лишнего....удачи и успехов+++

@hhbus2000 3 жыл бұрын

This product will cost about $400 or more if you try to sale it. I saw the oak wood speaker you made at Oct. Both very good. A builder make every detail even in side the box under cover 100% perfect. Hard to believe. The idea you hook up the Makita battery is very good. I have a lot of Dewalt batteries, try to think a way to use them, you give a good example. Thanks.