DIY Car Dent Repair 👍 Car Bodywork Repair

No video

DIY Car Dent Repair 👍 Car Bodywork Repair

Рет қаралды 5,851

Күн бұрын

DIY Car Dent Repair 👍
In this video, I demonstrate a DIY car dent repair using a dent repair kit I purchased off eBay. Watch as I tackle three different dents on my car's bodywork for the first time. With a bit of perseverance and the right tools, I manage to start to see an improvement. If you're considering a DIY approach to dent repair, this kit gets a thumbs up from me!
#DIYCarRepair #CarDentRepair #DentRepairKit #EBayDentRepair #CarBodyworkRepair #FixCarDents #DIYCars #CarMaintenance #CarRepairTutorial #DentRemoval #diyautorepair

Пікірлер: 33

@PaulHayman-tq5kb 3 күн бұрын

All IT is prectice and patience and understanding

@rustyrestos 3 күн бұрын

Definitely, the dent kit will not get it absolutely perfect like a professional PDR would, but it’s an old workhorse everyday driver Mondeo that hauls everything from dogs to tip rubbish, a £30 spend to get the dents to barely visible was worth it to me.

@kape9004 Ай бұрын

Great video, thanks. The tools you bought are cheap enough to give it a go. The dents look a bit better for your efforts, so well done you. I'll give it a go on the wife's car. And you're right, it could cost you quite a lot to take it to a repair shop. I've done loads of repairs on my home, garden and car myself, and probably saved thousands over the years. I'd sooner spend a few bob on a specialist tool for a job that I can do myself, rather than have to pay an hourly rate for someone to do it for me. For those of you out there who are thinking of becoming a DIYer, then start small. Buy a basic tool kit, do small jobs to gain confidence. And if you're taking something apart, film or photograph it so that you'll know how to put it back together. Good luck and stay safe.

@rustyrestos Ай бұрын

Good advice and all the best. I’m going to give it another go with the other stronger glue stick and see what happens. I’ll do a short video and see if I can get them even better! Thanks for watching 👀

@andyarmstrong1493 Ай бұрын

@@kape9004 Totally agree 👍

@PaulHayman-tq5kb 3 күн бұрын

Me advice would be to take the head light out and your Will be able to get the dent from behind

@rustyrestos 3 күн бұрын

Thanks for your advice and thanks for watching 👀

@andyarmstrong1493 Ай бұрын

I've used the bronze one. Persistence is key, keep trying and each time the dent will lessen. It's not a one shot device. I got really good results on my black Santa Fe.

@rustyrestos Ай бұрын

I agree. Thanks for watching 👀

@davidsargent4508 Ай бұрын

Oh my days. I had to watch the slide hammer technique several times as I was in disbelief what I was seeing

@rustyrestos Ай бұрын

It was my first go! Never done it before! Thanks for watching though 👀

@knoxyish Ай бұрын

i ....... got a pro in brilliant ! slide hammer mens banging the other end not the end wwith spring on!

@b4tm4nrubin33 Ай бұрын

I was thinking that to 😅

@rustyrestos Ай бұрын

Thanks for watching 👀

@stevejelly3161 Ай бұрын

Great video 🙂 . I've enjoyed watching videos like yours from the USA ......... they heat the metal to soften it (i think)....... but the kit should have a "wedge" shaped plastic tool to glue on ????? . They also have a "centre punch made of plastic".......... to soften the metal before pulling . . But ???? ............... You did a great job anyway mate 🙂

@rustyrestos Ай бұрын

Thanks for watching 👀

@stevejelly3161 Ай бұрын

@@rustyrestos No problem ... they sometimes "overpull" and tap them back in with small plastic thing with a pointed tip as they stare into a screen of black squares 🙂

@pwkk53 5 күн бұрын

😅Who the hell has shown him to do it like that ?

@dantheman3k Ай бұрын

its not working because you are using both tools completely wrong......

@rustyrestos Ай бұрын

Yes probably… but it has worked after many attempts (since this video was made). Thanks for watching 👀

@raypilgrim6905 Ай бұрын

I don't know why I'm watching this probably hanging on to see if you mastered the slide hammer.

@rustyrestos Ай бұрын

Thanks for watching 👀 it was my first attempt. 😂

@philf5043 Ай бұрын

Your glue gun is not hot enough, your using the lifter all wrong , you should warm area first with hot air gun to soften paint and you should tap down the crown around tye dent first. Some good vids on here , suggest you have a look or get a pdr man bef9re you cause more damage.

@rustyrestos Ай бұрын

Thanks for watching 👀 while I agree with heating the area up first as I mentioned in the video myself, the glue gun was hot and melting the glue. It’s an old car I like to tinker with. I have now got all the dents out after many attempts! 😂

@joshuairizarry423 23 күн бұрын

Im sorry, but you were doing extra work cause you were doing it all wrong.

@rustyrestos 23 күн бұрын

I know, I got there in the end and learnt something new. It creates a reaction via the comments which is good for the video 😂Thanks for watching and commenting 👀

@trab5933 26 күн бұрын

Doing it all wrong

@rustyrestos 26 күн бұрын

It was my first time ever of having a go! To be honest I have since improved and removed the dents so I must of done something right! Thanks for watching 👀