DIY | Casting Vacuum Chamber

Рет қаралды 44,852

Күн бұрын

Thank you for Watching and Supporting my New Channel!
*********************************************************
I am building by myself my own Workshop at home for Casting, Machining, and Pottery.
*********************************************************
Products Used in the Video:
1. Crystal Clear Epoxy Resin:
amzn.to/3cr6HGP
2. White Foam Board/Sheet:
amzn.to/3sYdxdb (3/16" or ~ 5mm)
amzn.to/3qw09eF (1/8" or ~ 3mm)
3. Single-Stage 12CFM 1HP Vacuum Pump (Reasonable Price)
amzn.to/3ejaBUH
4. 5 CFM Dual Stage Air Vacuum Pump (Great Choice)
amzn.to/2OyuHPX
5. Oil Filled Vacuum Pressure Gauge:
amzn.to/3quAW4m
6. 1/4" Ball Valve:
amzn.to/3bqCJmG
7. Brass Ball Check Valve, 1/4" (optional)
amzn.to/3bt5iQJ
8. Male or Female Hex Nipple:
amzn.to/3qmTeER
9. 1/4" ( Male End Air Hose Pipe Fitting
amzn.to/3ce61US
10: High-Temperature Silicone Vacuum Tubing Hose ID 1/4":
amzn.to/3rwZwD6
11: Dust Collection Hose 1 3/16 OD
amzn.to/3qw0M81
12. 1.5 inch (39mm) Waterproof Heat Shrink Tubing/Sleeve:
amzn.to/2Odxy0D
13. Refractory Mortar:
amzn.to/2MVkY5C
********************************************************
Camera and Lens I used:
1. Sony Alpha a6000 Mirrorless Digital Camera 24.3MP:
amzn.to/38lleCy
2. Meike 35mm F1.4 - Sony E Mount:
amzn.to/3kVXARZ
********************************************************
They are Amazon Affiliate links with my Store ID: tncreation09-20 - It means if you purchase a product by click through one of those links, I will receive a small commission (at no additional cost to you). Therefore, please consider clicking through those links, this is a great way to support my work and my Channel.
Thank you very much & Warmest regards,
TN Creation.

Пікірлер: 41

@TWFDeadzoneII 3 жыл бұрын

This is a really good video. I also like how you list everything that you use in video. It really makes it easy for someone following along.

@stur.7502 Жыл бұрын

Your saw blade should always be set no higher than a 1/4" inch above your workpiece/material.

@jamesphillips7283 Жыл бұрын

Really scary watching him cut material.

@martincastro7134 Жыл бұрын

Awesome video! Thanks for share!!!

@simple1278 2 жыл бұрын

This is fantastic tutorial with fantastic voice. Thanks

@ldmmmo9410 3 жыл бұрын

Great Video TN ! This must be the first DIY Casting vacuum chamber I found on KZfaq. Thank you for sharing!

@TNCXBUNBOX 3 жыл бұрын

Thank you !

@manuel3100 3 жыл бұрын

Muchas gracias era lo que buscaba ya tengo la bomba de vacío gracias en verdad

@Hamza-xk3pg 3 жыл бұрын

Great job with ur work. I have plan on making your DIY furnace. Just waiting on all the equipment to come in!!!

@TNCXBUNBOX 3 жыл бұрын

Excellent! All the best to your project Hamza.

@AllTheNamesWereInUse 2 жыл бұрын

Great video! Subscribed :)

@solano79 2 жыл бұрын

Nice! I appreciate your ingenuity. Just curious why vacuum through both chambers? Why not just connect directly to each chamber? Is it to dissipate the heat from your casting chamber to protect the vacuum pump?

@CONEHEADDK Жыл бұрын

I agree. Very nice work, but the whole thing seems far over complicated to me. I'm a keeping things cheap and simple kind of guy.

@oldkingcrow777 11 ай бұрын

If both run simultaneously its because he just doesn't have a split/valves 😂

@ErSeubb 3 жыл бұрын

Also, does the vacuum machine handle high temperature of casting or it melts down? Because I need to build one like you for METAL vacuum casting...

@sarawatechnology7070 3 ай бұрын

This is really good, I am sure I can adapt it so I cam make it here in Fiji. I subscribed and can't see the video you mentioned about DYI gaskets. Please post a link to it

@stringerb8618 10 ай бұрын

Hello Sir I have been learning from you and your skills thanks for the work you do for us. I was wondering if it would be possible to make a pressure chamber attachment that can push molten further into the small crevasses of a mould to achieve better quality result ?

@chrissilliker8633 3 жыл бұрын

Do you think it's harder to achieve a vacuum on your casting chamber this way instead of removing are directly from the casting chamber?

@Streamcatcher 3 жыл бұрын

Very nice video and creations! However l, I cannot find the video of how you made the metal flasks. Do you have a link?

@unioy 2 жыл бұрын

hi, what kind of mortar did you use on casting chamber is it high temperature ? also I cannot find the video how to make the high temperature rubber gasket and the rubber sprue base on how to make them ?

@new_comment Жыл бұрын

Very nice, really professional! What do u think about using resin potted SMD LEDs? Don't know how ppl work in gloves, so hard 4 me.

@davegeorge7094 7 ай бұрын

Can't get high vacuum with the big hose outlet leaking, Hope you can block it off!

@hothmobile100 9 ай бұрын

Excellent job. Wish I could just pay you to make me this.

@ErSeubb 3 жыл бұрын

Hi, I would like to know how did you craft the silicone reduction for the flasks, which material did you use, what temperature di they handle?

@TNCXBUNBOX 3 жыл бұрын

I will try to make short video soon about this, I'm sorry for this belated video. FYI, I made it from High temperature silicone ( Fire resistance Sealant) and RTV Silicone

@lannabulls 3 жыл бұрын

Very nice tutorial, thanks! Sorry for my question, what about the led bulb that you put inside both chambers, what they are there fore? Thanks again, owesome job!!!!

@TNCXBUNBOX 3 жыл бұрын

Hi Luca, I just put 1 led bulb (not both) in the main chamber for clear vision when I work in my workshop. Thank you for supporting my videos and channel!

@drumhailer547 5 ай бұрын

Does that saw blade lower 😬

@fabiogomes1145 2 жыл бұрын

Hello! Just a quick question! You say that a 7-9 CFM pump is an ideal pump but you recommend in the links a 5 CFM. Is a 3/4 CFM pump enough? Also did you use the casting vacuum chamber yet to any actual cast? I was hoping to see videos of that on your channel! Did it worked? Good job and all the best!

@TNCXBUNBOX 2 жыл бұрын

Hi Fabio, in my link they are 2-stage vacuum, which is more than enough.The 2-stage works stronger but cost a little more. I could not add the information once i uploaded the video. But if you have a 1-stage vacuum, it is better to have a 7-9 CFM pump. About, actual vacuum- i have been using it a few times for my small project, it works great, just the product wasn't great to make a video :)) :(.

@user-zv1cr9jm3o Жыл бұрын

great video! What service do you use for voice-over?

@TNCXBUNBOX Жыл бұрын

Please checkout Voicemaker.in - It í a great webbase app and it's free too

@skrebneveugene5918 Жыл бұрын

are you from Poland?

@noviceartisan 3 жыл бұрын

W'hoo, I'm the 666th subscriber ;) mwahhahahahaha xD Interesting solution dude!

@TNCXBUNBOX 3 жыл бұрын

=))) 🤣😅 Thank you 👌

@mikemcdonough1793 2 жыл бұрын

Blade is way too high.

@prestiapreciousmetals2475 2 жыл бұрын

never cut wood with your blade that high and push through on the peice on the fence please

@TNCXBUNBOX 2 жыл бұрын

Noted! Thank you very much for your advice, indeed!

@storieefoto 2 жыл бұрын

mi sa che devi cambiare la lama....non taglia

@ryanjones3084 2 жыл бұрын

Please please up your saw knowledge first thing your blade is way too high you should be a half inch to an inch above your surface your cutting being all the way up like that there is a chance that your back tooth will bind and send your wood back into your stomach! Second if you get a new blade that has a thinner tooth profile you will get way nicer cuts with way less smoke! If your piece of wood smokes or Burns at all you need to replace your blade