DIY Coin Battery Charger

DIY Coin Battery Charger - LIR2032

Рет қаралды 7,939

8 ай бұрын

🔋 In this tutorial I explain how to make a cheap and simple DIY coin battery charger!
📚 Instructables guide: www.instructables.com/DIY-Clo...
🧰 Materials:
- One Clothespin
- LIR2032 battery s.click.aliexpress.com/e/_Dda...
- TP4056 module s.click.aliexpress.com/e/_DB3...
- 5mm x 0.1mm Nickel Strip s.click.aliexpress.com/e/_Ddc...
- Resistors s.click.aliexpress.com/e/_DBt...
- Female and Male Pin Header s.click.aliexpress.com/e/_DDd...
- From 26 to 18 AWG Wire s.click.aliexpress.com/e/_DF4...
- Soldering Iron s.click.aliexpress.com/e/_DdG...
💟 Please support me and my projects at this link allmylinks.com/dariocose
Instagram: / darioc0se
Telegram: t.me/DIYElectronicsDiscount
Thingiverse: www.thingiverse.com/dariocose...
#tp4056 #lir2032 #batterycharge
------------------------------------------------------------
Music:
"Happy Rock" by Top-Flow-Production
pixabay.com/it/music/indie-po...

Пікірлер: 30

@Janktzoni 4 ай бұрын

Good ideas for both the jumper-resistor and the clip!

@robertalabla 4 ай бұрын

The resistor is almost shorted at the pin header. The clothespin offers no reverse polarity protection. A 2032 cell holder is cheap to buy or can be salvaged from old computer motherboards.

@user-se2pb5yx5p 3 ай бұрын

They expire fast.

@mrdavpen10 5 күн бұрын

Hello. The lir 2032 is rated 3.7 volts. Do you think it can be used instead of cr2032 that is rated 3.0 volt in a keyfob for example ? The voltage difference can cause some sort of problem? Thank you.

@dariocose 5 күн бұрын

What is a keyfob? Good question. I suggest you check the device datasheet before connecting a battery with a higher voltage. If you don't have a datasheet or professional test tools, ask the seller or manufacturer...

@freedomforever8168 8 ай бұрын

WONDERFUL

@jackisgoofingoff5510 7 ай бұрын

Interesting projects

@dariocose 7 ай бұрын

Thank you man!

@ANDREACAMPAGNA 8 ай бұрын

Cool👍

@lavacat720 8 ай бұрын

nice idea

@dariocose 8 ай бұрын

thank you!

@nasarsyammach4015 4 ай бұрын

Genius 👍

@dariocose 4 ай бұрын

Thank you, grazie mille! 🙏

@born_to_be_wild_ 5 ай бұрын

Nice Idea, man! What is the resistor's value?

@dariocose 5 ай бұрын

I use a 47k resistor, so the charging current is lowered to about 30mah

@Mehhh_was_here 3 ай бұрын

@@dariocose so basically the less mah the higher the resistor? My second question is why did you solder the resistor to the pin? As it has two pins cant you directly put in the jumper?

@dariocose 3 ай бұрын

@@Mehhh_was_here hi. 1) in the datasheet of tp4056 (or in this video kzfaq.info/get/bejne/q8ecf9qKt7isZo0.html ) there are the tables and formula for choosing the right resistor. In general, the higher the resistance, the lower the charging current. 2) I have no idea why I soldered the resistor on the pins 😁

@ChannelSE80506 8 ай бұрын

Is the best 👍💯👍💯👍💯

@dariocose 8 ай бұрын

thank you bro!

@Golliyo 2 ай бұрын

that resistor just slow down the current but the voltage is 4.2 still dangerous

@markclark787 4 ай бұрын

how about a ML2032 charger

@dariocose 4 ай бұрын

I read a few articles. I don't think you can use the same charger for lir and ml. "They have completely different chemistries so they have completely different charging voltages and profiles." - electronics.stackexchange.com/questions/533265/protection-and-charging-circuit-for-lir2032-or-ml2032-battery - www.reddit.com/r/dreamcast/comments/g1atiq/lir2032_vs_ml2032/ you can try a charger like s.click.aliexpress.com/e/_DkRpijx or this circuit seems suitable and adjustable in voltage and current s.click.aliexpress.com/e/_Dne8NMD

@MACYNET323 2 ай бұрын

LIr 2032 have higher voltage, but you can add a diode in series on output + terminal for drop the V. and charge ML2032 ?

@jel0nkae142 8 ай бұрын

I thought they were single use

@dariocose 8 ай бұрын

Only the LIR2032 are rechargeable

@user-ex2lh6it6r Ай бұрын

Латексные перчатки не где купить? Взял хоз перчатки😂😂😂 И без них можно не убьёт током, да если было бы высокое напряжение и через них стрикануло бы😂😂😂