DIY EASY EGR VALVE REMOVAL & CLEANING GUIDE FOR NISSAN NAVARA NP300

Рет қаралды 82,988

3 жыл бұрын

Here's a quick guide on removing a Nissan Navara EGR valve and how to clean it as well. Leave a comment below for any questions and I'll try to reply as soon as I can. Help us grow our channel by hitting the SUBSCRIBE button.
Follow us on Instagram @ / btdgarage

Пікірлер: 66

@martinbramston2244 Жыл бұрын

Great video ,and very helpful "do it yourself info". Will tackle my 130K klms, 2015 NP300 with better confidence after your video. Will probably install the blanking plate ,depending on how much gunk has been collected as mine has been all highway kilometres. Many thanks again for your clear explanation. Now subscribed. Martin

@btdgarage Жыл бұрын

Thank you! :)

@vingasoline1 11 ай бұрын

Salamat sa video sir. Detailed but concise and easy to follow. More videos pa po 😊. Sana lahat ng diy videos katulad ng gawa nyo

@btdgarage 11 ай бұрын

Thank you! :)

@babyfaceshotgun6042 3 жыл бұрын

THANK YOU for this video boss.

@BaoHoang-hl7ue Жыл бұрын

Thank you so much. The content of this video is clearly and effective

@btdgarage Жыл бұрын

Thank you :)

@MyTimmy75 8 ай бұрын

I'd just put on an EGR blanking plate on. And be done with it. The engine will thank you too. No more crap being recirculated back into the engine ;)

@_Alfa.Bravo_ 4 ай бұрын

That is bad for the enviroment. Shame on you

@rupert5390 2 жыл бұрын

Thanks so much I've paid $4000 for injectors, $1500 for ERG pipe it turned out to be the ERG valve and not one of the nitwit aussie mechanics picked it - you video is excellent

@btdgarage 2 жыл бұрын

Thanks! Hope your car is fine now 😊

@Tonksyyy_ 3 ай бұрын

What were the symptoms? Injectors noisy?

@rupert5390 3 ай бұрын

I was wrong wasn't the ERG it was the metering valve ended up trading it in as is - the symptoms where a ferocious knocking like the engine was going to explode - did that for a bit, i.e. - when driving if you lugged the engine in higher gears it didn't happen so much - until turned off because it was frightening - also at times just would not fire kept turning g over with no ignitioyou are.n - then when left fro a few days it was like new ran perfectly - I suspect a couple of mechanics knew what it was and kept milking out - the shame is one was a premier5 Nissan deaslershisop - also sincere apologies to Aussie mechanics - one u8tube mechanic actually made a video about the importance of metering valves - so there @@Tonksyyy_

@Tonksyyy_ 3 ай бұрын

@@rupert5390 damn. I think I’m gonna trade in mine too, never been that happy with it

@ryanventura5216 2 жыл бұрын

How about sir cleaning the intake manifold...do you have a video? Thanks...

@vinskyluk7546 2 жыл бұрын

Great video!!, Mas magaling ka pa sa master garage!!

@rupert5390 2 жыл бұрын

Many many thanks brother

@christianbryanarias480 Жыл бұрын

After cleaning EGR, any need for ECU relearning or whatever?

@SVSukha 6 ай бұрын

Great video followed and worked great for about 3 days then went back to running like shit and heavy black smoke, Will pull it out again and clean it better. I would add also to have something under the EGR Valve when pulling the 2 coolant lines off as I did not and got coolant on my belt and squealed terribly for a week. I'm thinking of putting a blanking plate on but cannot find one here in Mexico. Anyone know if I take sheet Aluminum or Stainless steel and use the gasket as a template will this work?, obviously not cutting out the centre part.

@mattgibson7647 8 ай бұрын

Is this the same for a 2016 pre adblue model?

@dboss2120 2 жыл бұрын

How regularly should it be cleaned

@jorhan06 2 жыл бұрын

Mine has 120 mil km, will try this asap.

@franpozo6848 13 күн бұрын

Leyend🔥🔥🔥⚡️⚡️⚡️⚡️

@P_daki86 7 ай бұрын

Great tutorial. Thank you! Question: Can a blocked/ filthy egr cause a diesel smell to come through the air con into the cabin?

@btdgarage 7 ай бұрын

Nope, it shouldn’t :)

@jondarahsabahanborneo1797 2 жыл бұрын

how about close EGR

@77FINNBEAR Жыл бұрын

Great content! Just trouble shooting my throttle body. Removed the pipe from the intercooler To inspect and clean. Discovered that the plate is stuck in the open position. Any thoughts.

@btdgarage Жыл бұрын

Hi! Unlike gas engines, diesel throttle bodies are normally open as default. They’ll only close upon shutting the engine down. You may confirm it’s operation by idling the engine with the hose/pipe of to observe the throttle body butterfly then turning the engine off (butterfly should shut close, then open). Just make sure you have scantool ready to clear any fault codes or check engine light afterwards as the ECU may get a low boost reading and throw a CEL

@truongminh3731 Жыл бұрын

thank you video ! 23-12-22

@faisalmohammed439 3 жыл бұрын

hi . what about canceling the EGR ? it is good ? and if i cancel it do i need to programing the vehicle

@daniellarno7477 2 жыл бұрын

No just block the ports with a blanking plate from ebay and you will be sweet as..

@q3rfasd2w88 10 ай бұрын

thx

@far1977 3 жыл бұрын

What is the total millage should I clean the EGR?

@btdgarage 3 жыл бұрын

Best to have it cleaned every 50K miles

@ryanventura5216 2 жыл бұрын

What is the size of the star torx socket sir?

@emmanuelmendez2237 8 ай бұрын

E8 size of star socket

@jordanmoore9556 2 жыл бұрын

How many kms on the engine for this egr clean?

@_Alfa.Bravo_ 4 ай бұрын

No, the question is if the engine gets warm enough , so long trips or short trips

@mikekohlmeier8720 3 жыл бұрын

If disconnect agr valve will the motor controll light be on?

@btdgarage 3 жыл бұрын

Make sure it’s connected before starting the car. If you leave it disconnected it might throw a check engine light

@mikekohlmeier8720 3 жыл бұрын

@@btdgarage Thanks. Regards from Thailand Mike

@_Alfa.Bravo_ 4 ай бұрын

@@mikekohlmeier8720 ... Grüße aus Nong Khai.

@jkpisces Жыл бұрын

Hmm mine are 12mm and not 10mm

@babyfaceshotgun6042 3 жыл бұрын

boss, can i use a WD40 for cleaning te EGR valve?

@btdgarage 3 жыл бұрын

WD40 is a lubricant, better to use petrol or carb cleaner for it. Just keep the EGR/sensor upright to avoid liquids seeping in and damaging the sensor

@babyfaceshotgun6042 3 жыл бұрын

@@btdgarage Boss thank you for the info. God bless

@btdgarage 3 жыл бұрын

@@babyfaceshotgun6042 God bless you too bro

@ryanventura5216 2 жыл бұрын

Ano po size ng star socket sir?

@emmanuelmendez2237 8 ай бұрын

E8 po ang size ng star socket

@pbatacan 2 жыл бұрын

Dumating na blanking plate ko from thailand. I think i dont need to disconnect the coolant hose since iblablank ko lang naman dba

@btdgarage 2 жыл бұрын

Yes no need na

@briethlayson3270 Жыл бұрын

its way to easy than the montero gen 3 😱

@phillipph7205 3 жыл бұрын

Can I DIY this? Is there any special tools needed?

@btdgarage 3 жыл бұрын

Absolutely. No special tools needed except for the torx star socket to remove the studs

@benitomarquezjr9448 2 жыл бұрын

@@btdgarage what size of torx ?

@welostv 3 жыл бұрын

Bos magkano nmn magpagawa ng ganyan sa mga shop. Any idea lng..

@ernestg21 2 жыл бұрын

bro just inquire to my Motech Auto shop they are charging.. ang clean egr sir labor: 2800-20%=2240 cleaner: 350 total: 2590 ung turbo cleaner hnhntay q pa po ung inorder q po eh 😊😊😊

@soyjoshuasaveukraine9888 4 ай бұрын

Boss after cleaning egr no need relearning?