🚨 UPDATED DAILY! BEST DEALS on AMAZON: bit.ly/48FGnUv ☑Check out my sponsor to begin your FREE 14 day trial to Aura: aura.com/chrismaher Govee Aura Smart Lamp: amzn.to/394HbWT LED Lights WS2812B on Amazon: amzn.to/3pngBDO AliExpress LED Lights WS2812B: s.click.aliexpress.com/e/_Der0k7N LED Controller ESP8266: amzn.to/3bah4y2 Glass Cylinder: amzn.to/3ceYNkX Stencil Paper Cutter: amzn.to/3e7ymgP Stencil Sheets: amzn.to/3lKa27N or www.hobbylobby.com/Crafts-Hobbies/Stencils-Craft-Paints/Stenciling/Stencil-Blanks---12%22-x-18%22/p/27038 Wood - I used 1 in. x 6 in. wood (not 1 in. x 5 in. that I mistakenly said in my video) Wooden Rod: amzn.to/3ccgIbQ Black Mesh Canvas: amzn.to/3f7XGVM Vellum Paper Roses: www.hobbylobby.com/Scrapbook-Paper-Crafts/Paper-Cardstock/Vellum-Paper/Black-Floral-Vellum-Paper---8-1-2-x-11/p/80763915 Vellum Paper Hearts: www.hobbylobby.com/Scrapbook-Paper-Crafts/Paper-Cardstock/Vellum-Paper/Black-Sketched-Hearts-Vellum-Paper---8-1-2-x-11/p/80870494 Power Cord/Adapter Cheaper option: amzn.to/3dpIwdX Power Cord/Adapter More power option: amzn.to/39csyAV Extension Wires: amzn.to/39a4azQ Jumper Wires Used: amzn.to/37mAqPd Soldering Iron: amzn.to/3s0kgmq Solder: amzn.to/2ONlaVn Solder Smoke Absorber: amzn.to/2ZpYaNS Helping Hands: amzn.to/3jUe3FW Circular Sander: amzn.to/2M6ai3x Acrylic for Router - amzn.to/2QnhxGb Hole Saw Cutter: amzn.to/3vQ4VaW Roundover Router Bits: amzn.to/3lKtmlF Spiral Router Bit: amzn.to/3lLn2KI Plunge Router I recommend is Bosch based on compatibility with more accessories: amzn.to/3seQ33C The one I use in this video is: www.harborfreight.com/2-1-2-half-hp-plunge-router-37793.html Links to a few of my other complete how-to projects: RGB Baseboard Trim: kzfaq.info/get/bejne/f9Foe9F43cy1oWQ.html DIY Customizable Images: kzfaq.info/get/bejne/aNePrdV2yMi8eHk.html RGB LIGHT PROJECT: kzfaq.info/get/bejne/qK-Sh92GqZipZJ8.html LED Strip Diffuser Ideas: kzfaq.info/get/bejne/Zp9dmcyIz7aYYo0.html DIY Hexagon Project: kzfaq.info/get/bejne/qp-oetxzmcfMqY0.html DIY Corner Project: kzfaq.info/get/bejne/kKhle9SIzbO8fqM.html DIY Edge Lit Designs: kzfaq.info/get/bejne/ZsWEp6ucp6iXpnU.html DIY Govee Glide: kzfaq.info/get/bejne/pJ98psyCpriqkac.html DIY Black Acrylic Floating Shelves: kzfaq.info/get/bejne/bMmjhrClu8XToGQ.html Videos to help with steps: Flashing WLED on ESP8266 kzfaq.info/get/bejne/oJdlo82GmL--lps.html kzfaq.info/get/bejne/b8pibLZzvKeYgac.html Crash course on how amazing and easy using WLED is: kzfaq.info/get/bejne/oJdlo82GmL--lps.html kzfaq.info/get/bejne/bMtzeJVz1bLFhYU.html Couple Video’s I watched to help me learn the basics of soldering: kzfaq.info/get/bejne/h-CJlZyYvLe9pJc.html kzfaq.info/get/bejne/bNideNWoupupXZ8.html Music Used: Song: DayFox - Kyte High Music provided by Vlog No Copyright Music. Video Link: kzfaq.info/get/bejne/l99_ZtVknt3IcWQ.html #NoCopyrightMusic #VlogMusic #VlogNoCopyrightMusic Particle House feat. Le June - I Don't Mind The best way to help support my channel is to like, comment, make sure your subscribed and share my videos with as many people as you can. The other way is to use my links above as I get a small % at no extra cost to you if you buy something. Thank you all for the support!

it actually looks better than the original

Nicely done, I really like the fact that you can change the inlay/paten on the light. Adds more versatility for the light.

Chris your creativity and humor is amazing. This turned out incredible. I love the black mesh as well. Love you bro!

This is my favourite. Works better than dealing with a traditional bulb. I never thought of this.

Great video Chris. Thanks for doing these projects and documenting them so well for us.

Love your candor and humor Chris. Great video

A very nice job and well explained. I really like the black grids in front of the LEDs. Thanks for the video.

Your videos are so good...you explain each step so well and your projects are so nice and unique.

Love the look of the light with that hearts velum paper, nice work dude

For not having the quote "correct" tools you made it work really good, It looks very nice!

There is only a certain direction that you should move the router bit in to make a safe cut. If you run it the wrong way you chance for the router taking off on you. There are great how to videos on making safe router directions. And as always, you make THE BEST instructional videos out there.

That mesh looks so 🔥

Thanks Chris, I'm definitely going to make this.

Look for a circle cutter to a German YT Chanel look for the Video:“ Kreisschneider Oberfräse Let‘s Bastel „

This looks just remarkable

That looks so good! Nice work! Keep it up!

Hello sir!. I hope your channel grows more! it helped me a lot for DIY! specially on the RGB

Very nice video Chris. I dally enjoyed watching it. Keep up your good work.

I like the mash look

Your ideas are Epic. Keep the good work. :)

That looks fantastic brother

Amazing job!!

Sand blast your glass, you can even tape patterns into. Night hawking light

Very cool

Looks amazing

Govee needs to hire you for design and progression!

I found some glass food containers at TJMaxx that I'll be trying to remake this with it. The only issue is it's open from one side only, so I have to cover the bottom of the container (Which will be the top of the lamp) with something to make it look good.

Great work!!

Brother your work is really great 💜🙌🏻✨

Chris, in one of your other videos you were using a table saw while wearing big clunky gloves. I was worried for your safety. If your bare finger touches the blade, you hopefully just get a nick and carry on. If your big clunky glove touches the blade, it will catch and be pulled into the blade area most likely causing a severe injury. I wouldn't want that to happen to you or anyone else. It is best and others will tell you, not to wear gloves when using a table saw. Please be safe as we all want more videos from you.

wow looks really good x3

Great stuff man

hella dope great video

I wonder if this could be 3D printed, you could 3D print the base along with the center cylinder that goes up to the lid, and print the top lid separately. Then coil the LEDs up the cylinder just like this. I'm very tempted to try this!

Look so cool

Great video! A quick question, can I use a 22awg cable ? Or what’s the best awg for a 4pin led strip?

great videos man

Unique night lamp 👍

yours looks so much better

great video

nice job.

Dare I say it but the DIY one to me looks better than the original

Awesome

i have nade a one using polycarbonate tube, results are amazing !

niceee brooo, speaker on Top and thats the shit! 🔥

I am trying to replicate this on a larger scale, a 10' pole. My question is I bought all the same materials as in the video but my LED out of the box have at both ends 3 wires going into connectors and 2 power wires, for total of 5 wires. I assume this is for connecting them & power? But, do I just cut off these connectors and follow the video with soldering 3 wires to the strips, jumper wires, going to the upgraded power supply? Thanks so much! Love your channel. After this I am building the VU Meeter. All for a project I am doing!

Rustoleum has a frosted glass spray paint have you tried that yet

2:45 Build up the stripped portion with CA glue and baking soda, and re-thread it. 30mins clear epoxy will work the same.

Hi, Iam making something similar but got a problem. I used most of the same hardware that you used except the board. I used a Wemos mini D1. In the video you powered all of the leds with a normal phone charger. When i did this only like 5 leds light up. How did you get them all turn on? I tried different cables (even powered via PC only powers 5 leds). Thanks!

Love your videos. Out of curiosity, how much did it cost you for this project including your labor charge. Just wanted to compare the prices and see the benefits of DIY

The real glass makes it look better than the "original" imho. If you had used a larger diameter inside tube you might've been able to hide the electronics inside the lamp itself, only leaving the power chord. That would protect the twisted wires from mechanical stresses as well.

What I can’t seem to understand is how does the app know which leds to light up first so it creates that seamless gradient look cuz the leds are just wrapped around randomly? How does it work? My head just can’t seem to grasp how it works 😅

Impressive

I didn't know that was how the lamp worked, i expected there to be a whole blurred led screen behind.

This would be great with a captive touch sensor. However, I have no idea how to install one on the esp32

keren bang

Yours is heaps better

I feel like you could do a good Morgan Freeman :)

It's a shame that you didn't show the only thing that would interest me. How do you control the LED controller? How do you set the patterns? How do I turn on the device? Why is the LED controller not integrated in the lamp? How much did the material cost you?

Take my money now!!!!!!!

This thing is cool as fuck, I copped 2

What software you use?.

It looks better than the govee

Hey this is a simplified version gyverlamp

Good DIY... Liked it😍😍😍 but video is very slow.

Don't use electrical tape over exposed wires. Use shrink tubing instead or you risk a short, or even a fire.

Нужно было покрыть тиковым маслом.

Incorporate a cheap Bluetooth speaker to it and it would be even better

It’s called a drill not a drill bit!!

Think I would rather save money and just buy the govee lamp

Ixnay in the usicmay. Just say no to snippets of vocal music.

Ок, ты сделал корпус для лампы, а как сделать умную лампу ни слова ни сказано... Ok, you made a housing for a lamp, but how to make a smart lamp is not a word said...DIY version of the Govee Aura Smart Lamp If we really talk about a "smart" lamp, then here is a much more interesting way kzfaq.info/get/bejne/bZ1hYLKcy5bIiac.html

The Govee looks like a nice item... but why ruin the product by putting your name on it when the literal point of the product is to look appealing? Well, I guess making your own item solves that problem!

do u have instagram ?