DIY Home Made Silicone Mold for Epoxy Resin

Рет қаралды 46,851

Hinkleshop Custom Design and Fabrication

2 жыл бұрын

In this video I show how I made a silicone mold for epoxy resin that was way cheaper than buying one
So easy to do with a two-part mix from the big store on the internet this was a great DIY project that was a lot of fun to make
You can start looking at the kits here be sure and purchase the correct amount for the project size you're doing
www.amazon.com/Silicone-Makin...

Пікірлер: 42

@derekrahme4629 Ай бұрын

No introduction, no unnecessary commentary. Just straight directions and getting down to business ! Just the way I like it.

@Purinelz 11 күн бұрын

great job brother awesome work thank you

@Hinkleshop 11 күн бұрын

@@Purinelz you’re welcome thanks for watching

@fordcountry8282 9 ай бұрын

Most helpful video on making a mold. Thanks

@Hinkleshop 9 ай бұрын

Thank you

@kaylamoyer7297 2 жыл бұрын

Very nice.. up next an ammo epoxy table?

@ndo104no 10 ай бұрын

Use respirators!!! Always use in well ventilated areas!

@timbergeron3067 Жыл бұрын

Great video. I'm looking to make a similar mold, around 18" x 12" x 2" deep with walls about 1/2" thick. What are the dimensions of yours and how big of a silicone kit did you need for it?

@Hinkleshop Жыл бұрын

Thanks for watching sorry for the slow response I used a gallon kit But if you go on the total boat epoxy website it has a liquid calculator for free

@wogar11 Жыл бұрын

Hi! Can I then, when the resin in the mold hardens, pull out the resin without taking apart the box (formwork)?

@Hinkleshop Жыл бұрын

Thanks for watching! yes once it cures you can pull it from mold

@wogar11 Жыл бұрын

@@Hinkleshop Thanks :)

@BILLBRAZIL100 7 ай бұрын

You mentioned that different colors for different strength. What is the color for a firm (strong) result , please .

@Hinkleshop 7 ай бұрын

Blue I believe

@patsyferreira5821 6 ай бұрын

I have a short round vase with legs. How do i make a mold for that 🙏

@Hinkleshop 6 ай бұрын

I would create a water tight vessel and place the vase inside it (after spraying the vase with mold release) Then pour around the vase The inside will be more tricky you would have to pour in the vase and remove it after it cures then suspend the molded inside plug over the outside molded vase

@chrisrhymes7258 18 күн бұрын

Can pvc be used for mold

@Hinkleshop 18 күн бұрын

I would say yes if you use release spray

@lesbsocal9107 7 ай бұрын

How do I make a mold for something with a hole in it?

@Hinkleshop 7 ай бұрын

Thanks for watching If the hole goes all the way through the finished piece, simply screw a block of wood or some other material in the desired shape in the position where you want the hole and pour the silicone around it. Hope this helps.

@sterchinwe4454 Жыл бұрын

What did mix no description

@Hinkleshop Жыл бұрын

The mix is a one to one ratio

@OOAK-Ireland Жыл бұрын

same mould for 45 use , the silicone you have in your description is 135 use... am I missing anything?

@Hinkleshop Жыл бұрын

Thanks for watching. I don’t believe you’re missing anything. The one thing I have discovered since this video was published is the different colors of silicone indicate the stiffness level of the silicone I recommend using the blue colored product.

@sucrebaba2656 6 ай бұрын

What is the name of substances A and B?

@pyroasura3266 3 ай бұрын

Hello from 3 months ago 👋 Part A is called hardener Part B is called Resin They go together when making things like this

@jcgarcia4699 Жыл бұрын

Can you tell what is the materials of these silicone to make a mould?

@Hinkleshop Жыл бұрын

Thank you Search Amazon silicone molding and it will come up

@jcgarcia4699 Жыл бұрын

@@Hinkleshop thank you so much👌

@michealazosibe3367 10 ай бұрын

Hi, how can this soap mold

@Hinkleshop 10 ай бұрын

Hello Not quite sure, I would say make a mold and give it a go on a small scale

@ianmc87 Жыл бұрын

I tried doing this with painter's tape but the epoxy stuck to it. I had better luck with regular packing tape. Don't know what went wrong.

@XGuard04 7 ай бұрын

He made a silicone mold in the video. That blue mold would then be used as the mold for an epoxy pour, not shown in this video.

@Hinkleshop 7 ай бұрын

@XGuard04 correct I show that in the bullet casing charcuterie board video it’s the very next one the following week Thanks for watching

@ved-5522 9 ай бұрын

In which ratio add resin and hardnar

@Hinkleshop 9 ай бұрын

50. 50

@michealazosibe3367 10 ай бұрын

And your contacts

@BuckysCustoms 2 жыл бұрын

Making your own molds save you any money?

@Hinkleshop 2 жыл бұрын

Yes sir roughly 50% or more

@Arifkhan-jt7zw 10 ай бұрын

Contact

@sucrebaba2656 6 ай бұрын

What is the name of substances A and B?

@Hinkleshop 6 ай бұрын

The containers are sold as a kit on Amazon They don’t give a description of what they are. Search 2 part Silicone mold kit