DIY How To Replace a Leaking Tides Marine Dripless Shaft Seal in Simple Steps

No video

DIY How To Replace a Leaking Tides Marine Dripless Shaft Seal in Simple Steps

Рет қаралды 22,050

Elli-Yacht

Күн бұрын

Пікірлер: 28

@scottbadgley3718 Жыл бұрын

Definitely switching to Tides dripless when my current ones go bad. Having extra seals lined up for easy replacement is BRILLIANT!!! :)

@robhowen Жыл бұрын

Super demo! I have these and now I know how to change. Thank you.

@phillo1818 Жыл бұрын

With popcorn in hand I was nervously anticipating a Titanic-ish disaster. My engineer is a CPR expert so not to worry Jon… Great job, you made it look too easy, have a good week y’all!.

@ElliYacht1 Жыл бұрын

I love popcorn and I know CPR and I hope that neither of those will happen in the engine room *K

@ericmitchell5350 Жыл бұрын

Nice Video--makes me wish my PSS seals were Tides.

@CaptnButch Жыл бұрын

I have the same system and always wondered how I’d do the changeout someday. Very useful information!

@SocalMarineUSA Жыл бұрын

Wife and myself also toying with the same idea :) safe journeys!

@ElliYacht1 11 ай бұрын

Thanks, you too!

@larryflorida5695 4 ай бұрын

Good video and good comments. Made replacing mine easy, however hard to just get to. I went down to do this project with a full stomach... bad choice... working half upside down in a hot bilge was not good.

@DarkSevariant Жыл бұрын

Great Job, Skipper...!!!

@ElliYacht1 11 ай бұрын

Thanks!

@RobertHuizinga Жыл бұрын

Jon-what a brilliant video. Thanks for calming the fears on water entry-I have the same system and have wondered how I’m going to handle it when the time comes.

@steveadams6010 Жыл бұрын

Well, Jon, yet another well done video for educating people on how to do things yourself, and do them right. Excellent videos, professionally done, well photographed, well thought out. Nice job buddy.

@paulgunter3624 Жыл бұрын

Tides are the next dripless seals I am going to install. The PYI have been nothing but trouble. I have replaced them twice and they start leaking after 1 or 2 seasons. Good video as usual.

@steveadams6010 Жыл бұрын

If you are going through dripless shaft seals at an unusual rate, there might be another problem. Many times a ding on the prop will translate into a small vibration in the shaft and into the dripless seal. You might not even feel the vibration but just because you don't feel it doesn't mean it's not there. Additionally, these vibrations can eventually act on, and start producing metal, in your transmission. As a marine surveyor, I have seen this happened before. I suggest a very close inspection of the propeller on the side of the shaft that continuously needs to be replaced. That might be the culprit-might not be, but it's certainly worth a look.

@capt.stubing5604 Жыл бұрын

Thanks for the great video. Needing to change mine after about eight years.

@marineequipmentitalia Жыл бұрын

nice!!

@jhance031 Жыл бұрын

I believe there is a little inner ring on the casing of the spare seal that is intended for use to help push the new seal into position (instead of hammer the new seal).

@GHanBax Жыл бұрын

Does the shaft seal need to be water fed? Or is that as is and just used the hose as a vent?

@heaven-is-real Жыл бұрын

A section of the propeller shaft is water fed and jacketed in water for lubrication while it is spinning

@randyjude8346 Жыл бұрын

Great diy video ( again) question.. when you're on the hard do you just install another future seal?... I do this with inside v- belts on the engine. Would make sense with the seals to me

@Jayda08 6 ай бұрын

It took me a whole 5 minutes to realize why the new seals were mounted on a shaft in the first place. 🤣

@UQRXD 9 ай бұрын

Nice engine room. Just saying, get some real tools. I would of lubed the shaft a bit first. The engine coupling on my boat would never be let to get looking like that. (Former marine diesel mechanic.) Live long and prosper.🥰

@Bigrignohio 2 ай бұрын

Pretty sure the instructions say NOT to lube (except maybe a bit of soap) as it can damage the seal. I expect that is a YCA instruction as people can and will use improper lubricants. One safe for the seal material would almost certainly be fine.

@yusdelpadron6822 Жыл бұрын

I changed my and it still leaking. I have to move the shaft to a position where is not. Wondering if my shaft is vent somehow or if my cutlass bearing is bad. Help. I forgot to mention that my isn't this eas, it's under the engine with not espace.

@breakingbolts8871 15 күн бұрын

Soft hammers are good. 😬

@captainsalty9022 7 ай бұрын

I still don’t know why people think these cleverly engineered seals are better than old fashioned flax and wax compression seals. Two wrenches and a $5 bag of replacement stuffing is all that’s needed. If you carefully monitor a fresh install, you readjust the compression until the drips just stop when at rest or reduce the drip to one a minute when running. It isn’t rocket science. A little water in the bilge helps keep it clean as it gets bilge pumped out with the crap that falls into the bilge from life aboard.

@brewster46 Ай бұрын

you are so right. I have had two emergency haulouts with PSS dripless seals.. one was the prev owner of my Sabre 42 and yesterday my Sabre 36 was taking on 5 gallons an hour underway running out of the PSS dripless bellows leak.. Not to mention that you need to haulout and 6 hours at $180 an hour to decouple the shaft, replace a PSS dripless, and put it all back together again. I had the old fashioned flax and wax in my Krogen 42. worked great and nearly costless.