DIY Linear Servo Actuator, 3D Printed
Рет қаралды 246,408
Күн бұрынThis video shows how to assemble and then run these DIY linear servo actuators (pusher style). Two sizes have been designed and made available for any project you have that needs a pusher style linear actuator.
An off the shelf version can cost around $70, while these 3D printed versions are much lower cost. Links to the STL files, part lists and affiliate links can be found below.
++++++++++++++++++++++++++++++++++++++++++++++++++++
If you like what you see, please support the channel!
/ potentprintables
www.buymeacoffee.com/potentpr...
++++++++++++++++++++++++++++++++++++++++++++++++++++
Follow me on social media for special updates and behind the scenes info:
Instagram: / potentprintables
Twitter: / potentprintable
Part lists and affiliate links
_______________________________________________________________
Mini version:
Thingiverse link = www.thingiverse.com/thing:317...
Myminifactory link = www.myminifactory.com/object/...
Non 3D Printed parts needed:
Continuous Rotation Micro Servo - FS90R
amzn.to/2ywr7uA [Pack of 1]
amzn.to/2VmTOnJ [Pack of 2]
JB Kwik 2-part epoxy
amzn.to/2q7U4IQ
Arduino Uno
amzn.to/2SbG2Ts
Adafruit Motor Shield V2
amzn.to/2q7SQ0c
2x M2 x 10mm screws
2x M2 nuts
_______________________________________________________________
Large version:
Thingiverse link = www.thingiverse.com/thing:317...
Myminifactory link = www.myminifactory.com/object/...
Non 3D Printed parts needed:
Continuous Rotation Servo - FeeTech FS5106R
amzn.to/2S3IjzX [Pack of 1]
amzn.to/2RrIl7d [Pack of 2]
JB Kwik 2-part epoxy
amzn.to/2q7U4IQ
Arduino Uno
amzn.to/2SbG2Ts
Adafruit Motor Shield V2
amzn.to/2q7SQ0c
4x M3 x 12mm screws
4x M3 nuts
As an Amazon Associate I earn from qualifying purchases.
Some inspiration for this design came from:
hackaday.com/2016/03/31/3d-pr...
WARNING: Please be careful when following any of the instructions from this video. Put your personal safety first and wear the appropriate safety equipment.
#3dprinting #diy #arduino #3dprinted #design
@jeremystowe2618 2 жыл бұрын
I just watched the KZfaq video last night, downloaded the STL files and 3D resin printed it this afternoon, this is a great design! Looking forward to attaching it to my airfoil to change angle of attack in the wind tunnel I have been modifying. Thank you!!
@sshutupurface8345 5 жыл бұрын
i like the grooves you made for keeping it level
@cupbowlspoonforkknif Жыл бұрын
I've spent dozens of hours over several years looking for something like this! Thank you! I have subscribed to help you out.
@obsidiantechz1371 3 жыл бұрын
I first struggled with the hub and pinion gear part but I got it now thanks
@greyfox0986 7 ай бұрын
Thank you! Just what I've been looking for. I am making a cosplay and I needed to figure out how to make a part extend and retract. I am a noobie so it's going to be a learning experience for sure!
@aaravbansal2476 Ай бұрын
thank you, i've honestly searched wayyyy too much, and then finally found this. solves the exact problem i was facing.
@seeminglyRANDOM88 5 жыл бұрын
This is a wonderful design and I am sure my students and I can use it in some of our robotics projects this year. Thanks for sharing!
@PotentPrintables 5 жыл бұрын
No problem! Send pictures if you do :)
@seeminglyRANDOM88 5 жыл бұрын
Potent Printables Will do!
@miketony2069 6 ай бұрын
This is great. Im going to use this make motorized drawer. Much less than the couple off the shelf motorized drawer openers ive seen.
@simonsuarez7561 2 жыл бұрын
Thank you for sharing it! This was really helpful
@ynnebbenny 2 жыл бұрын
This is great. One problem I encountered (My fault) when I printed this was I reorientated the pusher rod to fit flatter on the table. Because I rotated it 90degrees it caused an issue with rod not fitting into the slot easily. I guess my printer needs calibrating more precisely. I do think the pusher rod needs a flat plat so that the geared part sits on the printer plate without needing supports. Thanks for this file its a great addition.
@infinitx1330 3 жыл бұрын
first time seeing your channel, subscribed on the spot. Thanks for the files I can use them to build my bluetooth gate lock
@Willy_Tepes 7 ай бұрын
You don't need to glue the hub into the gear. Just cut most of the arms of a 4-arm horn leaving just 1-2mm. Then design your gear to accept this shape. I make drive gears down to a diameter of 12mm like this. Alternatively you can also buy steel or brass gears that fit the spline. 25T is very common.
@clarkkhoury 2 жыл бұрын
Thanks so much! must smaller than a traditional vertical actuator, thanks again
@henrytarveran1243 3 жыл бұрын
Brilliant job I must say, this is very good PRJS to implement..!!
@user-yx6nb6vg9j 2 жыл бұрын
you saved my capstone project! Thanks a lot..
@hmoazed 3 жыл бұрын
Thanks for saving me a bunch of time!
@MarkSwifty 5 жыл бұрын
Finally, I can print my own actuator for the duck coop door!
@PotentPrintables 5 жыл бұрын
Send pictures if you do!
@DavidBeukes 5 жыл бұрын
Thanks for sharing this. It's inspiring.
@PotentPrintables 5 жыл бұрын
No problem!
@nikbivation 8 ай бұрын
this is what I needed, thanks!
@PrintNPlay 5 жыл бұрын
It's awesome to see your dreams actuated
@PotentPrintables 5 жыл бұрын
This video has now been blessed, by recieving a comment from The Comment Master. :)
@mr3trashbagswatkins901 4 жыл бұрын
@@PotentPrintables do you have this WiFi controlled with a mobile
@ChrisRiley 5 жыл бұрын
These things are too cool man!
@PotentPrintables 5 жыл бұрын
Thanks Chris!
@faizalimuhammadzoda4731 2 жыл бұрын
Thanks for sharing. Keep it up!
@JeremyCook 5 жыл бұрын
Nicely done!
@PotentPrintables 5 жыл бұрын
Thanks!
@deadtech 5 жыл бұрын
Really great! Thanks!
@PotentPrintables 5 жыл бұрын
No problem and thanks!
@Much2shy142 4 жыл бұрын
Awesome! Thanks for sharing this! I may use this concept on my 3D printer to deploy/retract a mechanical switch for auto-tramming.
@anthonyjaylen6502 2 жыл бұрын
I guess Im asking the wrong place but does any of you know a method to get back into an Instagram account..? I stupidly lost the login password. I appreciate any help you can offer me
@darwinrussell8773 2 жыл бұрын
@Anthony Jaylen instablaster =)
@anthonyjaylen6502 2 жыл бұрын
@Darwin Russell thanks so much for your reply. I found the site on google and im waiting for the hacking stuff now. Looks like it's gonna take quite some time so I will get back to you later with my results.
@anthonyjaylen6502 2 жыл бұрын
@Darwin Russell it worked and I finally got access to my account again. I'm so happy! Thanks so much, you saved my ass :D
@darwinrussell8773 2 жыл бұрын
@Anthony Jaylen Glad I could help =)
@frightrisk7407 2 жыл бұрын
I had something very similar to this in my head and so glad I found you. I was picturing the toys that had a flexible "T" rack that looks like a big zip tie and you would push it into a flywheel assembly and pull it. Then put the toy down and watch it go. Can you 3D print is something flexible like that? Otherwise I am going to have to figure out the math of a slightly curved rack. I need to slide a 4' rectangular lid about a pivot point at one corner of the long side and have the opposite corner open about 8 to 10 inches. Imagine a coffin lid anchored at one corner and you push the other corner to open it. The line scribed by the rack would be slightly curved. Another option would be to have the rack have a circle at the end with a hole that mounts to a post so the post could rotate inside the hole. Or attach the end of the rod to a short rubber band to the post. Or the case itself can have the part that holds the rack against the gear be much shorter. That way, the rack could actually tilt a little bit around the gear since the arc is very shallow. I'm more an electrical guy than a gear guy so going through the possibilities ;)
@reggylippens6259 4 жыл бұрын
amazing that can be used in the predator wrist gauntlet to let the blades come out and safely back in else with other systems they jump out and on cons with lot of people its not prefered to have that your system is much safer to use greetings reggy
@MrPavlenator 5 жыл бұрын
Very useful detail !!!! Очень полезная деталь!!!
@PotentPrintables 5 жыл бұрын
Thanks!
@peixetstudios 5 жыл бұрын
Enhorabuena! Muy buen diseńo :)
@PotentPrintables 5 жыл бұрын
Gracias!
@antoniostefanile 4 жыл бұрын
thansk to share this idea
@PanDiaxik 4 жыл бұрын
1:11 It is actually possible to print these tiny teeth using 0.1mm nozzle. I have done it on my Anet A8 Plus. Maybe it would work also with 0.2mm nozzle.
@PotentPrintables 5 жыл бұрын
If you like this design, you may also like my DIY Motorized Turntable with Magnetic Attachment Plates: kzfaq.info/get/bejne/mah-rbuEr6y9emw.html
@PotentPrintables 5 жыл бұрын
I’d love to hear your ideas for how you might use this actuator in one of your projects!
@amyrocks10 5 жыл бұрын
Hi! I'm gonna use this in my self-resetting Rube Goldberg Machine. It's gonna be an arm that pushes mail into a mailbox, which triggers on a proximity sensor, and sends the mailbox flag up (connected to another servo) :)
@yorganyog 4 жыл бұрын
If I had a printer and time, I would make a version of Iron Man Suitcase Armor. Man.... How it's possible nobody made a decent thing????????
@stingraymaster877 3 жыл бұрын
Using it for a rc flamethrower. I used it to push the syringe full of yummy light fluid.
@ynnebbenny 2 жыл бұрын
I am building an automatic slide scanner.
@qozia1370 Жыл бұрын
Thank you so much. Ill modify it to press spray paint nozzle button
@annansubuga8307 Жыл бұрын
thankyou so much!
@annansubuga8307 Жыл бұрын
is there any way to o make the whole thing mpre quiet ?
@toxicslushpuppy 3 жыл бұрын
Thanks! All I can say is BLAAAAAAAADE!
@jbrill3829 2 жыл бұрын
What exactly do you mean by "tie the positive lead from the motor power supply into the v-in port of the motor shield"? Should I tether an additional connection from my battery supply to the v-in?
@yeshacroe9354 3 жыл бұрын
hello, may i ask what program you use to make the 3d design for this???? it seems very precise. Thank you.
@LeonYounger-ov5ro 3 ай бұрын
Goat
@sleepypenguin5977 4 жыл бұрын
Hello, was wondering, if i were to use a stock servo moto(meaning no mods at all) can it still work? I'm using this actuator as a way to overcome the dangerousness of people or workers that have to do maintenance on high tall wind turbines, and with this it might be easier for them to do maintenance as it goes down towards the ground.
@XFX4JOHN 5 жыл бұрын
Great
@PotentPrintables 5 жыл бұрын
Glad you like it!
@pasinduanjana2100 3 жыл бұрын
Great work. Thanks a lot. In my case, I need to send 8 inches of the rack. Should I increase the radius of the pinion or the gap between the teeth?
@keifer242 Жыл бұрын
Pasindu Anjana I need to do the same . Did you sort the problem
@aruskrisna4609 5 жыл бұрын
it is enough to push something more than 2 kg?
@ryanavery7980 4 жыл бұрын
link to mouse trap video? I dont have annotations on and cant turn them on.
@randallblake1213 2 жыл бұрын
Very nice! Question: How does the 3D printer print the overhangs? I don't see any way to reorient the model to eliminate overhangs.
@Willy_Tepes 7 ай бұрын
Use supports.
@ohanaentertainment7018 4 жыл бұрын
isn't connecting motor directly will wear out faster?
@RazanAltiraifi 5 жыл бұрын
Hi! Thanks for the inspiring video! Any thoughts on how to have a couple of actuators in one project? Maybe a grid of 4-6 of these with half going in one direction and half in the other. Would I need a separate motor for each? Thanks!
@RazanAltiraifi 5 жыл бұрын
Also can the speed be controlled?
@PotentPrintables 5 жыл бұрын
If you want to use one of these specific designs that I show in the video, you would have to use a motor for each actuator. However, with some redesign you could probably have one motor driving two pushers, going in opposite directions. Something kind of like what is shown here: www.thingiverse.com/thing:2305061 Note that the stroke lengths would have to get shorter for a dual type design.
@PotentPrintables 5 жыл бұрын
Yes, the speed can be varied for continuous rotation servos. The input variable for the .write() function can be varied from 0 to 180. 0 is full speed in one direction and 180 is full speed in the opposite direction. So values from 1 to 89 will vary the speed in one direction. And values from 91 to 179 will vary the speed in the opposite direction.
@DatFunnyPerson 3 жыл бұрын
is there a way to have something like this but just micro tiny?
@bondoman16 3 жыл бұрын
Do you know if you can run these (the mini) off an Arduino Nano board, withouth the seperate motor controller?
@chrisferraro5462 3 жыл бұрын
Great ingenious design. You've done a great job packing it all up for easy consumption! I printed the mounting bracket and gear without any issue, but had issues printing the pusher part as the 3D printer (Ender 3 Pro) was creating what looked like a spaghetti mess on the bed (note: I'm fairly new and inexperienced with 3D printing). After a bit of research and playing around with settings, I ended up rotating the object upright to print it vertically. After importing the .STL file into Ultimaker Cura, I was able to rotate it, which seems to be the best way to print without supports. I'm sure it could be printed horizontally with support material, but I wasn't sure how to do that. It would be great if somebody could confirm my approach or offer other insights. A second question I have, is how could make this pusher part longer? It is about 150mm in total with 145mm in travel. I'd like to make it about 325mm so I can get about 12" of travel. Any thoughts would be much appreciated. Thanks again!
@fishguylxo 2 жыл бұрын
Hey Chris, I've been thinking of getting a 3d printer myself specifically for Arduino/pi projects, did you manage to print it properly using the ender 3 pro, do you think there is something better on the market?
@chrisferraro5462 2 жыл бұрын
@@fishguylxo The technology is changing so fast, so I'm not sure where the Ender 3 Pro sits relative to other products today, but it worked well for me on this project. The printer was pretty low cost (under $250). I wasted a lot of PLA (the material that the printer uses for it's additive process) trying different settings, but that's part of the learning experience. By no means am I an expert with this stuff, but my suggestion would be to not spend more than $200-300 for a first printer until you get some experience under your belt.
@fishguylxo 2 жыл бұрын
@@chrisferraro5462 thanks for the info :) i did some research and i think the mini prusa is a printer i would go with for a start
@nickbrandon5327 Жыл бұрын
To get more travel you would need a larger drive gear, or do some multi-gear setup that allows the drive gear to spin more. Or, you could use a DC motor that can spin as many times as you need, rather than a servo motor that only goes 180 degrees. Using a DC motor would require a motor controller though, so the code and controls would get more complicated.
@prototype9000 Жыл бұрын
can you get the movement up to 400 to 600 cycles per second
@theGermanPrintingNerd 5 жыл бұрын
Cool Ali brings me Ides :-))
@PotentPrintables 5 жыл бұрын
Glad to hear it!
@olpscott9798 2 жыл бұрын
I want to attach the soil moisture sensor to the servo motor up down mechanism you showed so I can penetrate the soil moisture sensor anywhere I want. Will that work sir Or do you have any solutions.
@keifer242 Жыл бұрын
Hi, can you tell me how to make the rack 8" long. Thanks
@demej00 5 жыл бұрын
Why don't you drill a hole in the center of the circular gear for the standard sized servo so you can remove the gear from the servo if need be? The way you have done it here assumes the servo will never go bad.
@bloudman1 5 жыл бұрын
Hi ! Is it possible to get solid work's files ? I would like to modify it and I'm not able to with the STL format. Thanks !
@PotentPrintables 5 жыл бұрын
I included all the .step files in a .zip file with the STL files. That should let you modify the pusher arm.
@nitrotree745 4 жыл бұрын
how does the servo not break if it tries to push too far?
@AndrewAMG_ Жыл бұрын
Anyone have any advice how to get it to go past 180 degrees I printed the 100mm version on the large servo and I'm not able to get the full 100mm of travel.
@yugjain8134 4 жыл бұрын
How much did it cost you to 3d print the parts?
@TechnoPanda23 4 жыл бұрын
Hey I love this! Do you know if there is enough torque to move a 120 ml syringe?
@infinitx1330 3 жыл бұрын
Are you making any hydraulic project ?
@TechnoPanda23 3 жыл бұрын
@@infinitx1330 I was making a Ballast Tank!
@gameplays2961 3 жыл бұрын
Smart
@TheArashhak 5 жыл бұрын
What size is the screw?
@SG-zg3pc 2 жыл бұрын
Can anyone tell me what motor power supply I should use, given I am using the larger motor fs5106r
@kershawjoseph3496 2 жыл бұрын
Hey, can we do this with an Arduino Uno R3 and a Micro Servo 9g Sg90 Motor?
@danilakourkoulin7530 4 жыл бұрын
Hi, I have done all the steps and put everything in the right place but it would not work, Can someone help me trouble shoot my issues?
@didierdarcy7944 2 жыл бұрын
Bonjour votre site est super bien merci à vous où puis-je trouver le programme merci cordialement Didier
@NickDeVincentis 5 жыл бұрын
991 subs, lets gooooooooooooooo
@PotentPrintables 5 жыл бұрын
Gogogogogo!
@JGD16 5 жыл бұрын
Nicholas DeVincentis no unsubscribe
@JGD16 5 жыл бұрын
That 1k sure looks nice
@PotentPrintables 5 жыл бұрын
Yes indeed!
@CLUB2627 4 жыл бұрын
can i have the file to print the Actuator?
@ritesha8050 4 ай бұрын
hi what is the max force for the sg90 servo one
@yus3dp533 5 жыл бұрын
you could make another version with a limit switch maybe?
@PotentPrintables 5 жыл бұрын
That may be in the works :)
@yus3dp533 5 жыл бұрын
@@PotentPrintables cool
@Mynewhandle420 2 жыл бұрын
Where can I purchase 2 completed? thx
@suryaprakashp 4 жыл бұрын
Anywhere I Could buy an actuator like this considering I don't have access to a 3D Printer ?
@tigerx51v 3 жыл бұрын
I made an extra one of these, would you be interested?
@ascool7 2 жыл бұрын
Hello Can this press perfum spray head ?
@TW39 4 ай бұрын
Hi do they sell the mini linear acurators kits on the Google website
@justinjohnson4502 5 жыл бұрын
Is it possible to make the pusher arm longer?
@PotentPrintables 5 жыл бұрын
Yes it is. I included 4 different size pusher arms with the STL files. I also included the dimensions you would need to design an even longer one. Keep in mind that the longer it gets, the more the pusher arm will deflect and bend when it pushes on something.
@hafizmuhammadabrar33 5 жыл бұрын
I want to Buy this Servo Motor LineraActuator is it available in Pakistan?
@TheArashhak 5 жыл бұрын
Could you make one for Bluebird bms-max380?
@dockdrumming 5 жыл бұрын
Cool, but why do you need a motor shield if you are using a servo?
@PotentPrintables 5 жыл бұрын
You are right you don't- but the motor shield has the correct connector built in AND it supplies separate motor power to the servo(s), which helps prevent electrical issues when the motors are under load.
@dockdrumming 5 жыл бұрын
@@PotentPrintables So, I see. I guess that works better than supplying separate power directly to the servos? Well, having the correct connectors is definitely useful.
@produccionesonuba 5 жыл бұрын
Hello!!, thank you for this fantastic design!!. I have an Hitec HS-785HB servo that I need convert to linear actuator, but this servo has Length:2.32 in (58.9 mm), Width:1.14 in (29.0 mm) and Height:1.96 in (49.8 mm). Can I scale STL's to print linear actuator for my Servo?. Thanks!!.
@PotentPrintables 5 жыл бұрын
Thank you and glad you like the design. Unfortunately, I doubt scaling the STL files will allow for your servo to work with this design.
@produccionesonuba 5 жыл бұрын
@@PotentPrintables There is another method that I can use your design for my servo?. Thanks!!.
@HaidenMcGrath Жыл бұрын
How important is the motor shield board? Can you drive the servo straight off the Arduino Uno?
@Willy_Tepes 7 ай бұрын
Yes, servos use a PWM signal. You may however have issues with supplying enough current depending on the size of servo.
@ebtntw 5 жыл бұрын
question, can we use different motor (for more speed) and only but the parts?
@Door01 3 жыл бұрын
I'm sure if the dimensions match up, then yeah. Here's a link to the servo that is used's dimensions. images-na.ssl-images-amazon.com/images/I/71tf6GU8etL._SL1500_.jpg
@ebtntw 3 жыл бұрын
@@Door01 i graduated engineering already
@Door01 3 жыл бұрын
Yeah... I realized I was a year or two late to the party after reading some of the other comments lol
@user-jv9yo4rp4m 9 ай бұрын
alguien sabe el modelo del servomotor?
@TBharathi303 2 жыл бұрын
Hi bro . I need your linear servo actuator how can buy it
@Rctdcttecededtef 3 жыл бұрын
Total weight for each/
@alvinebacuado4079 4 ай бұрын
Do you have gcode file type for this? My 3d printer only print gcode
@abhishek_bhardwaj 5 жыл бұрын
Can u suggest a budget friendly 3d printer for beginners
@PotentPrintables 5 жыл бұрын
Hi- I recommend checking out some of these KZfaq channels. They have printer reviews and beginner guides for 3d printing. Maker's Muse 3D Printing Nerd Thomas Sanladerer Maker's Muse has a video that might interest you: "Cheap 3D Printers THAT DON'T SUCK $350 and under" kzfaq.info/get/bejne/jMCeYJidys3DoWQ.html Hope this helps!
@abhishek_bhardwaj 5 жыл бұрын
@@PotentPrintables Thank you sir
@JGD16 5 жыл бұрын
I haven’t watched it yet but FIRST!
@PotentPrintables 5 жыл бұрын
Hahaha, nice.
@mickistevens4886 4 жыл бұрын
Used a MakerBot Replicator+ 3D Printer and the pusher arm wouldn't fit properly. Had to do lots of filing to make it fit.
@mwdnow 3 жыл бұрын
same with ender 3
@ynnebbenny 2 жыл бұрын
me too. but its because your XYZ on your machine isnt calibrated well. You will need to recalibrate it. Also dont use rafts when printing.
@mohammedtauqeer9500 Жыл бұрын
Hey!..can u send me the design so that i can 3D print it...i need this actuator for my office work
@MoesKeckeEcke 2 жыл бұрын
How do you know where the servo is? there is no Potentiometer any where involved then... so it loses steps?
@AndrewAMG_ Жыл бұрын
I've got the same issue, I've got a home location then I need the actuator to move 1" forward then wait then move 1/2" forward then wait then return home. It needs to repeat this thousands of times and be able to go back to those locations with some precision. I had a 180 degree servo and it seemed super precise but would not travel enough for my needs so I got a continuous one and it never seems to be able to go back to the same spot ever.
@tejakrishna112 5 жыл бұрын
Hello...i need this gear system...where can i get that?..thank u in advance
@PotentPrintables 5 жыл бұрын
Hello- links to the STL files are in the video description.
@tejakrishna112 5 жыл бұрын
@@PotentPrintables is the gear system available in amazon.in...i need this for my project...thank you in adavance
@PotentPrintables 5 жыл бұрын
No it is not. You need to have a 3D printer to be able to make this.
@joeseibert7869 5 жыл бұрын
Hello, I am having a problem with the actuator returning to “home tooth”. I’ll explain, I used a sharpie marker and placed a dot on the cog wheel and the other on the pusher (to check for calibration and alignment)......when operating,the actuator pusher works as expected but with the exception of returning to the same “tooth”...... each time the actuator is activated it’s one tooth off from the “home tooth” that I marked with a sharpie.......the actuator works flawlessly besides this issue.... what could cause this problem or how to possibly fix?
@PotentPrintables 5 жыл бұрын
I'm assuming you have adjusted the delay time to try to get the actuator to retract for a longer time period? If that doesn't work, there might be a physical interference that is preventing the actuator from fully retracting.
@joeseibert7869 5 жыл бұрын
Potent Printables thank you for your timely response..... I have been messing with the times but, no matter what the times are it has the same problem..... switched the micro servo and it still has the same problem...... any other ideas?
@PotentPrintables 5 жыл бұрын
Does the motor/actuator grind or "skip" at any point during its stroke?
@joeseibert7869 5 жыл бұрын
Potent Printables no it doesn’t ....... when the program starts, the actuator moves forward....delay.... and then retracts.......... then I push the button on arduino to cycle again, but this time it will extend by one more tooth then retracts...... eventually if I cycle through the program enough times (3) then the teeth on the cog and pusher won’t align and it won’t retract..... I give it a little help when retracting and then when it gets to the home position it will drink the gears............ to sum it up, every time I hit the button it extends by one tooth
@joeseibert7869 5 жыл бұрын
Also I should mention, that when first powering the servo to the arduino the servo moves a little..... like it’s setting it’s self to home..... would that have anything to do with it? Is there a way to keep the servo stationary when first plugging power to it?
@NickDeVincentis 5 жыл бұрын
Put this in the "likely spam" folder
@PotentPrintables 5 жыл бұрын
Done.
@MrNams 3 жыл бұрын
Wheretobuy?
@tigerx51v 3 жыл бұрын
I made an extra one of these, would you be interested?
@justin60222 3 жыл бұрын
why do you not show it actually working?
@DeetDogg 2 жыл бұрын
Emphasis on the HUB
@gelatinskeleton8745 2 жыл бұрын
I wasn’t even aware there was a CNN PLUS…
@iiaethereal7518 4 жыл бұрын
Beyblade launcher
@HDFoxra 4 жыл бұрын
Not sure what sort of printer you're using.. But it makes some HORRIBLE quality prints... Majority of printers from a year ago would easily be able to print that part with an adequate amount of detail to fit perfectly on the servo...
notebook-31
Рет қаралды 81 М.
i-shoppers обзоры
Рет қаралды 1,6 МЛН