DIY Powerful Ultra Bass Amplifier From Capacitor, Simple circuit, No IC

No video

DIY Powerful Ultra Bass Amplifier From Capacitor, Simple circuit, No IC | DIY Audio

Рет қаралды 9,123

Күн бұрын

Learn how to build a DIY Powerful Ultra Bass Amplifier using a capacitor in this 12V amplifier tutorial. We will show you how to make a powerful amplifier circuit with simple components like transistors, resistors and a capacitor. No integrated circuits are required for this DIY amplifier design. Just follow the amplifier circuit diagram to build your own ultrabass amplifier with super powerful bass at home. This technical DIY project will teach you how to construct a handmade audio amplifier with deep, rumbling bass tones using a capacitor amplifier design. We can get up to 50 watts of earth-shaking ultra bass from the DIY Powerful Ultra Bass Amplifier From Capacitor. Follow along to make a simple transistor amplifier 12V circuit with big bass output using basic circuit design principles. This beginner electronics project will show you how to build powerful yet simple audio amplifiers with massive ultrabass output. The end result is an ultra-low budget but ultra-powerful DIY bass amplifier for your car or room that delivers amazing powerful bass!
#technicaldiy
#diyaudio
#diyamplifier
#diypowerfulultrabass
#powerfulultrabassamplifier

Пікірлер: 23

@DIY_Audio Жыл бұрын

DIY Powerful Ultra Bass Amplifier Using Diode and Mosfet: kzfaq.info/get/bejne/rJqJhNCL2ra5d4k.html

@kennmossman8701 10 ай бұрын

Do I have to smack the speaker, shake the parts, and tap the transistors?

@sandrabaez5909 9 ай бұрын

Oye bro pq tienes tanto hater si eres muy bueno haciendo amplificadores con buenos bajo pero puedes usar un subwoofer con su caja asi se escucha mas fuerte y mejor calidad

@kennmossman8701 10 ай бұрын

it is very unclear but it seems to be a somewhat basic Class B current multiplier - so the volume is very limited. That's why you need a very low speaker impedance. Are the transistors for switching or optimal for amplification - I suspect the former which makes them unsuitable. As well the soldering/connections are quite unsuitable for a high current circuit

@kennmossman8701 10 ай бұрын

How many amps are drawn at 12V Might it be 3 Amps at 12V So you need a rather massive battery/power supply

@kennmossman8701 10 ай бұрын

Did you make any measurements like THD. slew rate. S/N. offset voltage at output ????

@DIY_Audio 10 ай бұрын

Thank bro

@JoseFernando-ko5gk 11 ай бұрын

Isso é um sistema muito bem feito isso aí não é bateria não viu não tem nem como

@DIY_Audio 11 ай бұрын

Este é um sistema perfeito que pesquiso há muito tempo para ter sucesso. Se gostar, inscreva-se no canal para me motivar.

@kennmossman8701 10 ай бұрын

How many Watts[RMS] at 12V Peak Wattage would be less than 12W [12V, 2 Ohm speaker[ ? However with a more normal 4 Ohm speaker it would be 6W peak.???

@kennmossman8701 10 ай бұрын

No heat-sinks??? Class B or AB is somewhat efficient [more than classs A but less than class D] I am SURE heat-sinks would be needed especially since the TO-66 has a fairly high thermal coefficient.

@Promax-pv7vh 9 ай бұрын

Supply ? 12 24

@masafeeletronica5387 Жыл бұрын

Nice, very good!

@DIY_Audio Жыл бұрын

Oke thank bro

@rafaelalmiron2968 Жыл бұрын

Perfecto pero no es stereos, la música se disfruta más con salida a stereo! Podría mostrar la próxima?

@DIY_Audio Жыл бұрын

ok, la próxima vez haré estéreo, es genial que el estéreo sea mejor

@PPanos1968 11 ай бұрын

I don't see any logic on this circuit. All components are put wrong. Especially the 2 MOSFETs are connected Base with Source, and the left capacitor is reverse charged. Large resistors (4W) in series with 47 nF. Diodes with wrong polarity. And why 400V caps in a 12V circuit? Completely nonsense.

@DIY_Audio 11 ай бұрын

I think because you don't understand the circuit's operating principle, you have misunderstood how it works. You should review how I do it. I'm ready to answer if you need my help

@kennmossman8701 10 ай бұрын

@@DIY_Audio with no explanaton nor schematic it is hard to understand it seems to be a simple class B amp and I use the term amp very loosely since there is no voltage gain.