Explore a wide variety of content in our carefully curated KZfaq playlist: • Binge-Worthy Content Find more amazing tips at @TotallyHandyShorts #shorts
Пікірлер: 310
@dirtbikemike78152 жыл бұрын
WHY THE CRAPPY TACS EVERYONE DOES IT IT'S POINTLESS
@parkerr080 Жыл бұрын
Omg I hate how everyone of these channels weld like that
@marinecor23 Жыл бұрын
I didn't even see the welds. I came to bitch about the lack of heat treating and fractures forming in 2 of the bends o.O
@chiefchirpa6934 Жыл бұрын
Man shit like that pisses me off aye 😂
@abdul-rahmanal-surkhi Жыл бұрын
اللهم صل وسلم وبارك على سيدنا محمد وعلى آله وصحبه أجمعين 🧡💛🌲🧡
@Tagerrun Жыл бұрын
@@marinecor23 I came to bitch about him not being strong enough to just do it without the heat…
@joshyingling2 жыл бұрын
I only saw one time you actually used the heat in the rebar to make it easier to bend, you can do most of this work with the rebar cold
@PablosProjects Жыл бұрын
Yeah exactly
@calebalt1557 Жыл бұрын
it’ll crack, I’ve tried bending 90’s with 3/8 and shit’s so brittle it snaps
@justthetexan9961 Жыл бұрын
Yeah you can? but why would you when it makes the job a hell of a lot easier?
@feddy11100 Жыл бұрын
If you're insistent on using heat why not just use a propane torch while the piece is in the vice. That seems like it would be the fastest way.
@calebalt1557 Жыл бұрын
@@feddy11100 oxy acetylene is so much faster, way more heat, way less time to make it cherry red
@CodPlaent Жыл бұрын
I support you Johnny Depp🤣
@dustyluce43832 жыл бұрын
That welded (from pipe to plate) is not fused. Look at it, you see the "lack of fusion", on the bottom toe line of the weld. All that tack, tack, Mig weld BS, is just barely above the strength of silicone calk. Top Notch Product.
@ralph54502 жыл бұрын
Barely?
@shrxft2 жыл бұрын
@@ralph5450 yes barely, the welds are shit😂
@hellfire666832 жыл бұрын
Moderate breeze will pop those welds
@erich79452 жыл бұрын
The calk is probably stronger than those welds 🤣
@hellfire666832 жыл бұрын
@@erich7945 never underestimate the power of caulk lol
@user-hh9pe8br8b2 жыл бұрын
Да,сложная задумка.Автору класс!!!👍
@user-nn4fr7ek4k2 жыл бұрын
Нет мастера обидеть может каждый , хотя изюминка в этом есть легче ворота кувалдой снести чем шпингалет из арматуры сломать .
@pickle65992 жыл бұрын
Да просто манипуляций дофига лишних. Нафиг арматуру нагревать!? Достаточно тисков, ножовки по металлу и сварки, чтобы сделать хороший шпингалет.
@yarus802 жыл бұрын
@@pickle6599 так а какая разница? Он нагревал, вы може не нагревать, если соберётесь повторить, в чём проблема? Я думаю он нагревал исключительно для видео, ибо смотрится по интереснее.
@lucid_god Жыл бұрын
Ah yes I will do it myself with the forge and welder I have in my very room
@user-dt9fo9cy8b2 жыл бұрын
Fun, but that was a totally shity weld, that looks pretty.
@fawkyooo73772 жыл бұрын
Lol bruh your (spot welds are trash) I’ve seen some that are decent yours are even penetrating the base metal.
@awolstew10362 жыл бұрын
I was just about to say that about his lul tac welds
@Fuck9oogleAskMe2 жыл бұрын
Also they made a big effort to trim the video so that the arc is cut off from the video. Take the time to do a good weld instead 🤷♂️
@__.-.__hi8652 жыл бұрын
Yeah it looks to be flux core too
@willt718 Жыл бұрын
the rails on top of the forge are also his handiwork 👍
@michaeltumpach1173 Жыл бұрын
@@awolstew1036 p
@dailycereal6529 Жыл бұрын
Please for the love of god , lay some continuous welds instead of making a million spots
@MrSnorkeller2 жыл бұрын
А греть арматуру нахер? Она прекрасно гнется трубой на то она и арматура, чтобы быть пластичной.
@user-lw7dm4th3l2 жыл бұрын
Да там вообще куча всего лишнего
@taraskopyl99932 жыл бұрын
Позовите Доктора!)
@MrNeofelis2 жыл бұрын
Да это похоже какой-то дурачок. Арматуру всегда на холодную гнули. Он даже греет через ж...
@user-jj6jd7tn6q2 жыл бұрын
У арматуры марка стали 25Г2С это обычная катанка там марка стали Ст3сп, а арматуру если нагреть и закалить тогда она хрупкой становится
@saam14832 жыл бұрын
Не проще было щеколду купить готовую, чем это вот всё
@svt_mike66 Жыл бұрын
Why can't anyone on this channel weld? Let alone spot weld? 😂
@adamtheredneck48982 жыл бұрын
Why do you tack weld your stupid "latch" at least run a bead
@LethalAether2 жыл бұрын
Dude, Gordon needs that rebar to fight the Combine
@TCAPChrisHandsome2 жыл бұрын
DIY? Yeah, let me pull out my torch, welding machine, stack of bricks, and bench vise, that I keep on my bedside table.
@tzr58642 жыл бұрын
Tell me you're not a welder without telling you're not a welder
@jmathews4702 жыл бұрын
That bead placement of the "TACK" weld tho....
@RC.3RD8642 жыл бұрын
I love the work that you do! Who would I ever thought rebar could look so damn nice!
@nefertaribautista4282 жыл бұрын
Y
@kaushaldwivedi95362 жыл бұрын
@@nefertaribautista428 0000000000
@yozhikhyper1337 Жыл бұрын
Кто не в курсе, арматура нужна для изготовления железобетонных конструкций. Остальное от Лукавого.
@JustAPersonWhoComments2 жыл бұрын
note to self: practice welding
@josephemerian95452 жыл бұрын
Watch the legs on your welds. They're not even. You're awesome for making these videos keep it up
@dakotadaulton3148 Жыл бұрын
You have lost credibility with all welders
@pitviper-vp2vl Жыл бұрын
@@dakotadaulton3148 i second that statemnt
@strongbear012 жыл бұрын
La verdad no es necesario calentar la varilla para hacer eso
@randyherringshaw6325 Жыл бұрын
To make that latch stronger drill a hole in the plate, chamfer the back so the weld can get good penetration and then weld the catch on the front and back of the plate and grind it flush.... Just a suggestion!
@edgarromero1482 Жыл бұрын
Disculpen, eso se puede hacer en frío!!! No hay necesidad de calentar!!! Un herrero con experiencia no necesita realizar mucha maniobra para realizar ese tipo de detalles, en realidad solo necesita un par de ángulos, clavos, una grifa un pedazo de tubo y listo ✅️
@justinduarte57392 жыл бұрын
$900 in propane to make a$10 latch. Seems legit
@christopherjones7191 Жыл бұрын
Thats where the cost savings in the welding gas comes in
@collinstheone88142 жыл бұрын
Yo yo just a tip round the ends of your bend bars thank me later
@andriesdupreez4170 Жыл бұрын
Awwwww I know I will use the forge to hear the rebar so it’s easier to bend but I will wait un till it’s cold after I take it out So much waste of a force and propane
@michaelhorner9122 жыл бұрын
Def some cool stuff you make, but learn to weld. I subscribed
@theexplodedguys264 Жыл бұрын
Wish your welding be on a tig for that job. AND MAKE IT LOOK SMOOTH PLEASE.
@user-ys2mq7ff8x Жыл бұрын
У нас арматурщики так без горелки каждый день делают . При нагреве сталистая сталь теряет свои сталистые качества . Возьми обычный кругляк нах арматура
@user-sd3ok6kq9v2 жыл бұрын
Сварщиканец, мимо приварил то
@aleksandrkomissarow88312 жыл бұрын
Вы хотя бы шов по красивее делали полуавтоматом
@user-od2kb1xi6n2 жыл бұрын
Согласен
@thesiegeguyjack66792 жыл бұрын
So why dont you just make a continuous bead instead of a shit ton of spot welds
@turbogerek2 жыл бұрын
I think using induction device to heat that would be more easier and saves a lot of energy
@whatsup84642 жыл бұрын
He doesn't want the entire piece red hot...
@irishkelly2062 Жыл бұрын
I'm starting to think you tack weld just to piss folks off.
@MegaSherman15 Жыл бұрын
For the love of god……. First, learn how to weld. Running a bead is way more satisfying tbh. Second, you don’t need a furnace in order to bend rebar. Third, it’s not DIY IF YOU NEED A WELDER AND A PROPANE FURNCE THAT NEEDS REFRACTORY BRICKS!
@michaellance8982 жыл бұрын
Is it only me that knows this? You can easily bend the rebar without it heating up if it’s not to short.
@arnoldmmbb2 жыл бұрын
Where you get the rebars without rust? They always look like crap 😂
@ralph54502 жыл бұрын
You unrust them.
@LegacyLife_5552 жыл бұрын
@@ralph5450 wrong..that’s how they come..you have to ask for brand new reo as it tends to sit out side and it only gets a lil rusty it’s not deep rust
@ralph54502 жыл бұрын
@@LegacyLife_555 put in Muriatic Acid.
@swagpillage1917 Жыл бұрын
That guy was face reveal look like a Johnny depp
@thefuzzman Жыл бұрын
Question: if you're using a blowtorch to heat the rebar, why do you need an oven? Just use the torch to heat the rebar in the vice. 🤔
@taylordavison6849 Жыл бұрын
You know, you can just buy latches. You don't need the equipment and materials for this gas forge to heat up rebar to make a latch. Latches aren't that expensive and I'd imagine this setup probably costs more than a manufactured latch.
@Warriormedic68 Жыл бұрын
The fucking internet's idea of a "diy" is hilarious. If I had this much shit and specialized tooling... I wouldn't need a video to show me how to use it to make a rebar handle.
@Thecowboy19502 жыл бұрын
Nice door latch
@spire4101 Жыл бұрын
You can buy a bolt latch at home Depot for 5 bucks save you 3 hours and 25 bucks in materials.
@LordSergei2 жыл бұрын
Задвижка крайне не удобной конструкции
@zerotoeverything4348 Жыл бұрын
idk dude, ill just prolly bend that metal and call it a day i dont have time heating those
@cleaner992 жыл бұрын
What is the original rebar's HRC before & after the quenching?
@yt20yt2 жыл бұрын
Имея полный комплект оборудования просто приварить кусок гнутой арматуры? Бездарно...
@user-od2kb1xi6n2 жыл бұрын
Ты ЧО зато ВИДЕО БЛЕАТЬ
@afreightdogslife Жыл бұрын
I don't know why but I feel like I should go Home Depot and buy some rebar
@rogeriomeskita45592 жыл бұрын
A solda não fundiu dos dois lados kkkkk
@Kballs Жыл бұрын
Look at all that undercut!
@Pa3HOE_o_pa3HoM Жыл бұрын
Пацанчик, мой тебе совет, не занимайся хернёй с этой печкой для пиццы, возьми резак, на крайняк паяльная лампа из дедовского гаража для такой приблуды тоже пойдёт
@meloman482 жыл бұрын
Когда купил много арматуры по акции) что не видео, то с арматурой)
@blackholescience2 жыл бұрын
I'm not really one to criticize someone's craftsmanship but this thing is just scrap metal at the end. It's going to fall apart in a matter of days I immagine
@abbprrodriguez744 Жыл бұрын
Weld weld weld dont be scared !! No weld spots pls love u brother ❤
@taraskopyl99932 жыл бұрын
Я... Я.... Посрал, там прям.... Прям вываливалось... Вот отсюда! Вы, представляете?!
@eduardomelenchuk60672 жыл бұрын
А греть горелкой по месту не судьба?
@kota7789 Жыл бұрын
Wth was those tack’s holding? Over half didn’t even bridge the pieces lol
@yawmiyat-ismail Жыл бұрын
عمل متقون 👍🏻
@paulangel86412 жыл бұрын
Assim que eu vi já imaginei que seria isso
@Mongoliantreecow Жыл бұрын
"DIY" starts off with industrial sized kiln 🤣
@user-qu1jg9yu8k2 жыл бұрын
чел в России не был... армату нагреть ради такой мелочи ахаха
@handsfun39762 жыл бұрын
Почему когда я вижу надпись ДиАйВай, мне представляются обосра…ые руки .
@taraskopyl99932 жыл бұрын
Мне представляется мой лечащий Доктор)
@user-vb5nx1sr9z2 жыл бұрын
Греть арматуру что бы согнуть такой диаметр, смешно
@Ridinglawnmower145 Жыл бұрын
I was chillin with the video until the welding it’s like no one knows how to weld so they just have to do shitty spot weld everywhere
@flowsaify2 жыл бұрын
Rebar can be bend without heating also
@xMrjamjam Жыл бұрын
And with that heat transfer you just ruined the jaws on your vice. Get a leg post vice next time those are designed to hold hot steel and are designed to be hammered
@trollero57252 жыл бұрын
Aggg esa soldadura jajajaj espero aprendas a hacerlo suerte metele ganas
@user-yz9gn4kl7o2 жыл бұрын
Я думал выражение «приср*ть» применимо только к электродуговой сварки
@onyxwolfarias65232 жыл бұрын
i know u think its diy but it stops being diy when u need 100 dollars worth of tools and three diffrent certifications
@dirtbikemike7815 Жыл бұрын
100 buck??? Hell if I could find a propane furnace and a welder that are halfway decent under 2500 bucks I would shit myself
@onyxwolfarias6523 Жыл бұрын
@@dirtbikemike7815 butane torches are under 100 and u can use them to make a shit furnace
@dirtbikemike7815 Жыл бұрын
@@onyxwolfarias6523 ya that's true
@maheshmotwani4300 Жыл бұрын
Why are you irritating those rods go and buy in Amazon
@anurag4611 Жыл бұрын
Jitna kharcha or mehnat kiya hai na utne me naya aa jata wo bhi designer
@MrSikeLLa2 жыл бұрын
Ох и приварил😁
@williamhinkle81132 жыл бұрын
I torch where I'm welding the heat up that area first. Then weld.
@randal31222 жыл бұрын
not necessary
@mdnormatnor52262 жыл бұрын
When thunderstorm coming the rebar is not strike by lightning right.
@simonemariadasilva7708 Жыл бұрын
Wow all of that for a door thing that i forgot the name...thats why our future is coming way slower lmao 🤣
@vassilip53422 жыл бұрын
«Сварщик от Бога»
@Jrjacobtoler Жыл бұрын
Over cut the fawk outta those welds lmaoooo
@viktorlizunov66102 жыл бұрын
Все такие модные блять стали, уже электродами не вариться, есть же сварка тиг
@Pa3HOE_o_pa3HoM Жыл бұрын
Это не тиг, а полуавтомат
@BruceLee-qj8ve Жыл бұрын
Looking good but does it worth it...
@JohnJohnson-bg2oo2 жыл бұрын
Why's he using a forge to heat up rebar, and letting it cool down before he bends it?🤣
@InchFab2 жыл бұрын
Same reason he's not using a bottle of Mapp gas I stead of whatever the fuck that gigantic contraption is. For the 'gram, bro.
@2-_-62 жыл бұрын
Ты кроме ручек что нибудь делаешь?😁
@nateyoder9372 Жыл бұрын
Your welds barely even touch the bottom piece of material
@quq_CCCP2 жыл бұрын
Эмм, зачем? Засов стоит копейки, и почему арматура а не кругляк, тамибез загибания делается сваркой ручка...
@splitbolt2 жыл бұрын
Why does every DIY’er or “life hacker” weld like this??? 🤦♂️ ITS EMBARRASSING!! If I welded that I’d not only throw it out, I’d cut it into tiny pieces to hide the evidence. Just sayin’ Otherwise, cool video 👍
@user-eq5jx8dy8y Жыл бұрын
А смысл это все делать? Не проще ли к пруту приварить что надо и все?
@user-sq9cf4bq3w2 жыл бұрын
Нагадил там полуавтоматом, ужас)
@user-yd8kp5xq8u Жыл бұрын
И не забудьте залить арматуру бетоном!
@paulandersbullecer3152 Жыл бұрын
What's the difference between tact weld and the other kinds of weld. I know a little in construction and nothing in welding
@dirtbikemike7815 Жыл бұрын
Tac is to hold it in place to make adjustments if needed then depending on the thickness of the metal you lay a continues bead some can be a few inches long a few inches apart or some could be the whole thing jus depends
@xXNaywoodXx2 жыл бұрын
Gute Arbeit!!!!
@lukasjung971 Жыл бұрын
Nein
@Robocoppat2 жыл бұрын
Or you could just use oxy/ acc and heat it. It's much easier.
@SosShortsComedy Жыл бұрын
Excellent
@melnikovmmvz7775 Жыл бұрын
Можно было и обычный шпингалет сделать
@luismonet6985 Жыл бұрын
You don't need all that fire to bend the bars..🤪
@goinfishin9726 Жыл бұрын
Latch falls apart first time closing gate lol
@TheIMadeThat Жыл бұрын
Great, instead of buying a $10 latch I need to buy $300 of tools.
@dirtbikemike7815 Жыл бұрын
For a welder that's worth a damn like 750 to few thousand and a furnace for under 600 bucks good luck lma
@NAME_NEMO Жыл бұрын
В Челябинске так руками гнут без нагрева
@marekpusep67392 жыл бұрын
Криативно интересно но эти швы боже эти швы мои глаза!!!!
@user-xq4rx4rn1l2 жыл бұрын
Че то много движений
@Goigigandfriends2 жыл бұрын
You could have wasted less propane by using a torch 🤦♂️