DIY Shower Door Installation How To - Cantour Series by Basco Frameless Shower Enclosure

Рет қаралды 398,455

Күн бұрын

This video explains how to install the Roda Cantour shower door by Basco, which combines heavy glass with frameless clean lines, and features an innovative hinge that allows up to 6 inches of adjustment, making it simple to install - yet versatile - fitting today’s most commonly found opening sizes.
Here are the tools that you’ll need to properly install this door - and make this a simple project.
• 1/8” and 1/4” Steel Bits
• 3/16” Masonry Bit
• Drill
• Pencil
• Low Tack Masking Tape
• 4’ & 6’ Levels
• #2 Phillips Screwdriver
• Clear Silicone Caulk
• Caulk Gun
• Suction Cups (Recommended)
• Center Punch (if drilling into tile)
We recommend two people for this door installation due to the weight of the glass and fragile nature of the product. Supplemental instructions are available at Basco Shower door dot com. After carefully removing all contents from boxes and preparing your area with drop cloths and protective material, you’re ready to get started.

Пікірлер: 28

@richardsiatey2635 6 жыл бұрын

Superb thanks for teaching us

@romeodlive6607 6 жыл бұрын

Very very good job....nice installation

@marcurial777 4 жыл бұрын

Muchas gracias , me salvó la vida.🏆

@yukixie3932 4 жыл бұрын

This video does a great job, and every step comes to the point. Thanks for sharing

@alihasham1946 4 жыл бұрын

I am also doing this work

@felipelopez1116 3 жыл бұрын

@hamboza010 2 жыл бұрын

@@alihasham1946 فين؟

@alihasham1946 2 жыл бұрын

Yes

@kaleshsuthar6231 5 жыл бұрын

Very nice

@DJERUPSHUN 6 жыл бұрын

nice work, I like it

@ferinugroho1051 6 жыл бұрын

Good, i like it

@mokhlismahmoud4558 5 жыл бұрын

Feri Nugroho

@pareshrana6771 6 жыл бұрын

Good job

@niyiabdul6243 4 жыл бұрын

How can i get the hinge accessories imported please. I'm currently based in Lagos, Nigeria. Thanks

@tieubaoo 3 жыл бұрын

I have acrylic shower base. Do I still need drill hole through the aluminum rails and put down anchors?

@BascoShowers 3 жыл бұрын

Thank you for your question! The frame comes pre-drilled. If there is no stud behind your acrylic walls, you will want to use the anchors supplied in the hardware strip. We recommend not drilling into the base. The majority of our doors are sealed to the base with silicone, with the exception of our heavy glass frameless doors, which we do not advise putting on acrylic bases due to their overall weight.

@ahmedgmalden3533 5 жыл бұрын

Iam egyption iwork in saudia can the company send me permit work . i hope realy

@cgfdcvbh6015 5 жыл бұрын

اخي العربي من اين انت

@alihasham1946 4 жыл бұрын

I am doing this work in pakistan

@MotivationandInspiration-rd2ex Ай бұрын

Asslamualkim

@mdrahulamin5243 2 жыл бұрын

কাজ চাই আমি ডুবাই আছি

@shawnwalters641 6 жыл бұрын

Awesome now you have a leaky shower, good job fellas. You should never drill into the curb. Silicone or not

@martinwinlow 4 жыл бұрын

Nonsense. However else are you going to rigidly secure the bottom of the the fixed screen? In any event, a simple but properly applied silicone bead will ensure no water causes problems in the first place. Personally, I'd lay the channel on a small silicone sealant bed - paying particular attention to the screw holes. All that said, there is no way I would have such a high and wide upstand as it is an invitation for water to puddle and potentially cause problems. A mounded shower base would eliminate this issue and still allow for good connection to the fixed and moving glass screens and would facilitate entry and exit of the shower, especially for the elderly or infirm.