DIY throttle body sync

No video

DIY throttle body sync

Рет қаралды 36,076

Aaron Merchant

Күн бұрын

Home made throttle body sync for under 30$. All parts from lordco auto parts and a free board from Rona!

Пікірлер: 32

@mhiscott4925 6 жыл бұрын

Also a good tip for the tubing... Throw it in the clothes dryer on med setting for about 3 minutes. Softens and straightens the hose out so it's not a curled up from the spool.

@beehivevidz 6 жыл бұрын

GodSpeed good tip. Will need to try that out some time

@jasonbennett1131 3 жыл бұрын

This is why I love You tube easy to build stuff & ppl who chip in with great hints. Cheers

@900vasa 9 жыл бұрын

I used mine the other day and it worked like a charm. Bike runs great now!

@900vasa 9 жыл бұрын

Hey man! Great video! This is exactly what you want to find when you search for "how to make carb sync tool". We need more videos like this, basic level. I tried to sync my carbs with normal vacuum gages, but I find it hard to get it good since the needle is bouncing all over the place. But with this tool it seems really easy and exact! Would be fun to see when u use it. Cheers bro

@psyfertech 9 жыл бұрын

eric sanden i agree with you it seems like every other video you see when you search for this is just a video of the device in use not on how to build one but i actually found this very helpful i made one almost exactly like it i just used cardboard instead of wood for the backing

@beehivevidz 8 жыл бұрын

+Nick 636n8r (stuntn24-7) Thanks! i to looked all over the internet and couldnt find something detailed to build one. Finally decided to attempt making one and it actually worked out. Glad this video helped those who needed it.

@robertholsopple9451 8 жыл бұрын

thanks for the detail! I built one just like yours. I didn't try it yet but I know it will work. thanks again!

@Thatdavemarsh Жыл бұрын

Perfect. Nicely done.

@DonPedro6901 7 жыл бұрын

This flickering is making my eyes crazy!

@CrazycatRider 6 жыл бұрын

thankx for your tips i'll subs u

@beehivevidz 6 жыл бұрын

Crazycat Rider your welcome!

@AorusRtxGaming Жыл бұрын

sama2 bang hihik

@erhanalmas9959 3 жыл бұрын

How did you fill the fluids with hoses.?

@mhsucio6830 3 жыл бұрын

well...... did it work?

@fingloidfing3337 4 жыл бұрын

Can you use engine oil instead of ATF?

@sgtjoe2008 6 жыл бұрын

Can i use some kind of restrictor to each tube to minimize the tube length?

@beehivevidz 6 жыл бұрын

sgtjoe2008 the instructions I was following didn't call for it so I didnt do that

@forthebirds007 7 жыл бұрын

How did you get the AT fluid into the tubes after connecting everything? Just funnel it down the 6 foot tube or some other trick?

@beehivevidz 6 жыл бұрын

Jesse White just funnel it down

@beehivevidz 6 жыл бұрын

Jesse White acctually I remember now, it's not pretty but you literally need to put on side of the vynil tube into the ATS fluid and then suck back the clear end of the tube until you get the amount needed into the tube

@ancilblair7204 6 жыл бұрын

Hi does all the hose have to be same length

@beehivevidz 6 жыл бұрын

Ancil Blair no

@TeamSparkHere 9 жыл бұрын

Did you ever get to use it?

@beehivevidz 8 жыл бұрын

+TeamSparkHere Yup! worked great too!

@emmanouilgkoulis2709 7 жыл бұрын

finaly ...instructions...dude...!!!!!!!!

@maciek600r 3 жыл бұрын

Ten patent nie ma sensu bo nie pokaże wartości podciśnienia w psi, mmhg czy w bar czy są one po prostu prawidłowe, takie filmy jak ten to ogłupianie kolejnych ludzi przekazywane na YouTubie coraz dalej. Pozdrawiam

@maciek600r 3 жыл бұрын

@@stefanmelmak Ok. Tylko jak się ogląda te wszystkie filmy, to większość tych silników nie pracuje równo tym bardziej kiedy regulują gaźniki. W przypadku gsr-a jest łatwiej bo ma silnik na wtrysku i tutaj komputer będzie wspomagał utrzymywanie równej pracy poprzez map sensor, czujnik położenia przepustnic i czujnik obrotów. Regulowałem gaźnikówe i wtryskowe japońce przez 10 lat. Nie mówię że nie masz doświadczenia ale oglądają te filmy ludzie co będą to robić pierwszy raz i będą przeświadczeni że jest to słuszna droga. Pozdrawiam

@maximilianoolivieri9895 3 жыл бұрын

@@maciek600r I built it the same. I synced my suzuki GSF1200 to carburetors, and it goes beautifully.

@maciek600r 3 жыл бұрын

@@maximilianoolivieri9895 To gratuluję, ja mam profesjonalne podejście i nie bawię się w rurki i wężyki. Ja chcę mieć pokazany na wykresie cały cykl zasysania. Mnie ludzie za to płacą