DIY Unistrut Roof Rack | Sprinter Solar Panel Mount

DIY Unistrut Roof Rack | Sprinter Solar Panel Mount | Van Conversion

Рет қаралды 48,347

Күн бұрын

Join our van build extraordinaire email club here: bit.ly/3Apcz0r
Show your support by buying us a beer here: bit.ly/3bX58UE
________________________________________________________________________________
James and Sarah here, back with another episode in our Sprinter van conversion series. This week we’re up on the roof installing our DIY Sprinter roof rack and solar panel mounts.
As with most things during our van build, it took us a while to figure out how to build a DIY unistrut roof rack. But once we had all the parts, it was relatively quick and straightforward to put together.
Our camper van solar mounting system is simple, sturdy and inexpensive. And while designed for a Mercedes Sprinter van, there’s no reason the same setup wouldn’t work for any flat roof van with lengthways channels running down each side.
Hopefully we can save you a lot of time and money with the information in this homemade roof rack blog video.
There’s also a blog post on our website about which goes into more detail. Click here: thewholeworldornothing.com/di...
Thanks for watching! If you enjoyed this episode don’t forget to smash the thumbs up & hit subscribe so you don’t miss the next one.
Catch you in the comments fellas!
---------------------------------------------------------------------------------------------------------------------------
Here’s a list of the materials and tools we used in building our DIY roof rack:
- 2 x 3000mm Unistrut Channels (41x41x2.5): ebay.us/Fa6xzk
- Unistrut End Caps (x4): ebay.us/jLGC0i
- 6 x 1400mm Aluminium Angle (40x40x3mm): ebay.us/LZjJAR
- Mastic Sealing Strip: ebay.us/y3nOzq
- Sika 210 Primer: ebay.us/NEdajk
- Sikaflex: amzn.to/314N1D2
- M6 x 20mm Penny Washers: ebay.us/DrP1Xu
- Hexagonal M6 x 40mm Bolts: ebay.us/If76HV
- M6 Nyloc Nuts:ebay.us/NsWrwn
- 12 x Two Hole Angle Brackets (40x40mm): bit.ly/3dRbB1H
- Unistrut M6 Channel Nuts: ebay.us/TZgM82
- Solar Panel Cable Gland Box: ebay.us/xh3XF4
- Mini Heat gun: amzn.to/3dX92eI
- Trim Tools: amzn.to/3q2SS62
P.s. These are affiliate links, so if you buy through them we may earn a small commission from the seller. It’s at no extra cost to you so is a lovely way to say thanks if you found the video helpful.
Subscribe to our KZfaq Channel: bit.ly/32ZTD67
Follow our daily updates on Instagram: bit.ly/2ypQsXw
Visit our website: thewholeworldornothing.com
Full van tour video: bit.ly/3dVYWei
Full van conversion series: bit.ly/3dRSSDl
Work with us: hello@thewholeworldornothing.com

Пікірлер: 60

@marksmith4673 2 жыл бұрын

Excellent video guys, im literally following in your footsteps with my sprinter and did this part today. Love your vanlife content and the excellent walk through videos. Cheers!

@kevingalloway9338 Жыл бұрын

Love rewatching your videos it's help me out as I am building my own van now

@waheedtahan2428 2 жыл бұрын

Excellent work I'm learning a lot from you guys. I plan on buying my very first Sprinter cargo van by next month and mine should be ready in 30 days because of parts issues. Thank's for sharing this video.

@SamandMollieExplore 3 жыл бұрын

Hey guys, thanks for the great video :) love how your creating your own solutions to all these camper build challenges!

@TheWholeWorldorNothing 3 жыл бұрын

Ah thank you! Glad you enjoyed it 👍😀

@darrengregory6678 3 жыл бұрын

Hi you two, thanks another educational episode I’m a year behind your build and keep looking at your completed van episodes for layout ideas,

@TheWholeWorldorNothing 3 жыл бұрын

Hi Darren, glad to hear it! Let us know if you have any questions on the layout, we’d be happy to try and help.

@donaldindividual-1 2 жыл бұрын

Nicely done. I will use Strut material on my RV roof too. Very clean install.

@TheWholeWorldorNothing 2 жыл бұрын

Thanks! 👍 Good luck with yours too!

@jkcrypto8907 2 жыл бұрын

Great vid guys, I just ordered my unistrut bits and will be following along on your YT videos for instructions ! What a good way to save money instead of paying £400-£700 for a full rack ;)

@kevingalloway9338 3 жыл бұрын

Great job guys

@TheWholeWorldorNothing 3 жыл бұрын

Thanks!

@LonnieWormley 2 жыл бұрын

I got some ideas on how to install my solar panel on my 2017 ford Transit. Thanks for your inspiration.

@TheWholeWorldorNothing 2 жыл бұрын

Fantastic, glad you found it useful 👍

@garrykennedy5653 Жыл бұрын

Fantastic guys

@MyBoxingFitness 2 жыл бұрын

I like that the solar panels don't hang over the side of the van and look like wings, it's much tidier, this also allows you to attach a Fiamma. - Brilliant. :)

@catw6274 9 ай бұрын

You two are adorable. Nice job!

@darrengregory6678 3 жыл бұрын

Thanks

@zsofijakab9830 3 жыл бұрын

Hey, I'm early! Another great video, I've been waiting for it.😁 Have a nice day.

@TheWholeWorldorNothing 3 жыл бұрын

Ah thank you! Glad you liked it. Quick question, are you planning a van build yourself or just interested in them?

@zsofijakab9830 3 жыл бұрын

Yes actually, I'm planning to travel Europe one day in a van, but I'm still in school, so I'm just watching videos and making plans on my design at the moment. 😁

@TheWholeWorldorNothing 3 жыл бұрын

Amazing! Such a good idea 😀

@TheAffrojutty Жыл бұрын

Great job guys 👍 I’m looking to do something similar, what did you use to fix the angle bracket to the solar panels? Cheers!

@madeleinehughes4757 2 жыл бұрын

So helpful! How did you manage to tighten the nut underneath the channel nut once you had it on the unistrut?

@TyGunnlaugsson Жыл бұрын

Thanks for the video! What did you do with the holes that didn't line up with the unistrut holes? Have you noticed it whistling at all?

@Lostsome Жыл бұрын

Great video and job what size cable u use from controler to battery ? Thanks in advance

@nathanturner-whittle9525 2 жыл бұрын

Hi love the unistrut as a roof rack idea! Very modular as you can easily add to it down the line, quick question. Did you not consider running your wires from the solar panels through one of the unused plugs in the roof and routing the panel wires through the inside of the unistrut channel, that way saving you drilling a new hole in your roof

@waheedtahan2428 2 жыл бұрын

Great idea I'll do just that.

@gertsels1377 Жыл бұрын

Nice video! I'm thinking of using the same system for mounting the panels.. Unistrut rails are already installed. Ever had any issues or parts coming loose?

@mrgardiner4519 3 жыл бұрын

Evening all, just sorting out some pre-cut strut crossbeams for our 2014 MWB Sprinter high top, just confirming that the width between struts is 1400mm before I purchase :) Cheers J

@TheWholeWorldorNothing 3 жыл бұрын

Evening! While that’s a different year and size of van to ours, we’d assume that the width will still be the same and certainly not any wider. So yes, 1400 should do it 👍

@mrgardiner4519 3 жыл бұрын

@@TheWholeWorldorNothing ideal, many thanks :) If it helps anyone. I have sourced them from strutchannelsdirect.com, mainly due to them being pre-cut and powder coated.

@davep6977 2 жыл бұрын

Unistrut=erector set for adults (love to stuff) check out their catalog, the accessories are endless.

@royabayliss3277 Жыл бұрын

Hey guys just watched your video - really good.. but please would you be able to tell me where you sourced your unistruts etc for the DIY roof rack? I’m planning doing the same but also adding decking etc so need full length.. I have a Mercedes sprinter! Any tips would help!

@sky_daddy333 Жыл бұрын

Put two nuts on the bottom to make them lock and use the red stuff, the tread lock 👊👊

@jacobrobinson6001 Жыл бұрын

Hey guys! Love your videos. Quick question on this one - how did you end up fixing the panels (+angle aluminium) to the roof using the chunky aluminium bracket? I saw you playing with some methods (around 6:00 onwards) but you didn't clarify how you ended up securing them. Did you put the angle bracket on top of the long aluminium angle so the bolt went through both and into the channel nut? Or did you use a different method? Cheers!

@TheWholeWorldorNothing Жыл бұрын

Hi! Glad you’re enjoying the vids 😀 Yes that’s exactly what we did, the bolt goes through both and holds L bracket to the U channel 👍 Hope that helps!

@noahriding5780 Жыл бұрын

Do those unistruts come with the bolt kits to attach them? Thanks.

@TheWholeWorldorNothing 11 ай бұрын

No they don’t, we bought all of that separately

@somewhat7 3 жыл бұрын

4:44 may i suggest cutting or drilling a small hole on the bottom for water to escape?

@TheWholeWorldorNothing 3 жыл бұрын

Hmmmmm, hadn’t thought about that. I have a feeling that water flows out anyway but I’m going to check now to make sure 😅

@ThePistol1977 3 жыл бұрын

Great job guys iam thinking of doing the same to my van its a vw crafter just a quick question the nuts u put on the van to hold the unistut down what size screws didn't you use and was the van holes already heve trends in only asking because I don't know if i need riv gun hope this makes sense cheers 👍

@TheWholeWorldorNothing 3 жыл бұрын

Hi! The bolts we used are actually linked in the description, they’re the hexagonal M6 40mm ones 😀 We didn’t use a riv gun as we used nyloc nuts on the other side so it’s literally bolted on. Hope this helps 👍

@ThePistol1977 3 жыл бұрын

@@TheWholeWorldorNothing thanks for your reply much appreciated cheers 🍻

@TheWholeWorldorNothing 3 жыл бұрын

No problem! Hope it helps and good luck with the installation 😀

@neildoherty2199 3 жыл бұрын

Hi guys great job with the build , what guage of unistrut did you use?

@TheWholeWorldorNothing 3 жыл бұрын

Thank you! We put links to pretty much everything we use in the descriptions so you'll usually find product details down there, but this is the exact stuff we went for & the link- 2 x 3000mm Unistrut Channels (41x41x2.5): ebay.us/Fa6xzk 👍

@neildoherty2199 3 жыл бұрын

@@TheWholeWorldorNothing Thanks for the quick reply folks, I am on cef website just now to order up about £70 all in for everything i need : )

@TheWholeWorldorNothing 3 жыл бұрын

No problem! Great stuff, good luck with installing it 👍

@Outlander1963UK Жыл бұрын

Hi guys, did you use the 1.6mm light duty or the 2.6mm heavy duty strut.

@TheWholeWorldorNothing Жыл бұрын

We used 2.5mm strut here’s a link to the product - www.ebay.com/itm/392434561437?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=SAg9gRKkRra&sssrc=2349624&ssuid=&var=&widget_ver=artemis&media=COPY

@vickiwoods4412 2 жыл бұрын

Hey guys, can I ask where you bought the solar panel kit please?

@TheWholeWorldorNothing 2 жыл бұрын

Hi! It wasn’t a kit that we bought, we pieced together each individual element ourselves, but the solar panels and the mppt controller came from Photonic Universe. Everything should be linked in the description below. Hope that helps! 👍