DIY WINCH BUMPER for UNDER $100

Рет қаралды 62,211

Жыл бұрын

Save 10% Off your Vevor welder with discount code VVS10 bit.ly/3osSr6v
On this episode we build a custom winch bumper for our 1996 Toyota 4Runner! And we sure did it cheap, made with free scrap and $60 of new metal. We top off the bumper with 7" LED lights from Nilight!
Check out _broken_sensor on Instagram: / _broken_sensor
Support Dirt Garage by purchasing our Merch! - www.dirtgarage.ca
Brought to you by @ Alpine Toyota - alpinetoyota.com
INSTAGRAM - / dirt_garage
Get 10% OFF Afraid Knot Ropes with my discount code "dirtgarage"
www.afraidknotropes.ca/
Get 10% OFF Afraid Knot Ropes with my discount code "dirtgarage"
www.afraidknotropes.ca/
DIRT GARAGE MERCH!!!: dirtgarage.myspreadshop.ca/
My 2020 OFFROAD Gear Kit / Recommendations: USA Affiliate Links
Lunchbox Locker: amzn.to/34lDTfI
Smittybilt Compressor: amzn.to/2vhwEqm
Tire Deflator Tool: amzn.to/2SwmbPO
Smittybilt Winch: amzn.to/2HbKP2Y
Recovery Rope: amzn.to/39om3Ze
Soft Shackle: amzn.to/3bnRg0t
Hard Shackle: amzn.to/39ouyDA
Recovery Hitch: hamzn.to/2SeE6LN
CANADIAN Amazon Affiliate Links:
Smittybilt Compressor: amzn.to/35DcvY3
Tire Deflator Tool: amzn.to/2QBWPQA
Smittybilt Winch: amzn.to/35CBOJO
Recovery Rope: amzn.to/2s9qRlj
Soft Shackle: amzn.to/2R4j5Bx
Hard Shackle: amzn.to/39QXpl3
Recovery Hitch: amzn.to/306WyIL
Music Licensed @ Artlist
Find music for your videos on Artlist! artlist.io/Clinton-279876
My 1989 Toyota Pickup Build: • My DREAM Toyota Build!...
- 1UZ-FE V8 Swap
- Manual Swap
- Dual Transfer Cases 2.23 x 4.7
- Solid Axle Swap / SAS
- Lunchbox Rear, E-Locker Front
- OME Rear Springs & Tundra shackles
- Auxbeam Headlights: shrsl.com/38hjx
- 37x12.5r17 Toyo MT Tires
Camera Gear Used To Make This Video:
- Camera: amzn.to/36C4dkI
- Microphone: amzn.to/2QDkIaB
- Tripod: amzn.to/2sdCkR0
- Gimble: amzn.to/2FyndVf
Business contact: Dirt.Garage@outlook.com

Пікірлер: 133

@mrsdirtgarage1413 Жыл бұрын

MY SCISSORS!!!!!

@jacobgriffin2500 Жыл бұрын

As a husband and mechanic this is The most underrated and relatable comment ever!!! Haha love it

@megh9806 Жыл бұрын

😂

@Will-ht9cp Жыл бұрын

@@jacobgriffin2500 My gf has heavy duty gold colored shears that she uses for crafting and what not. One day I decided to use them cutting some chicken wings. We don't use her scissors anymore.

@jordanmercier3616 Жыл бұрын

@@Will-ht9cp my wife has those crafting scissors too, they used to be sharp until I couldn't find my snips and I had to cut wire one day lol.

@flyboy2610 10 ай бұрын

Nice bumper! Red Green would be proud! One tip about cutting steel with an angle grinder: Don't try to cut all the way through in one pass. Lightly score the steel with the first pass, and then make repeated passes cutting a little deeper each time. Your cutoff wheels will last much longer, and that saves money!

@dandahermitseals5582 Жыл бұрын

Those light I beans are salvaged from a mobile home floor frame. Dandahermit

@gregleblond9367 Жыл бұрын

i really like this, because this is how normal people would get it done.. not someone with a $150k dollars worth of tools and plasma tables etc... in a $250k shop....getting it done with cardboard and scrap plate.. love it

@mikejensen-fogt4662 Жыл бұрын

Your fab skills are definitely improving man, its great to see! Definitely better than the old go cart made from the bed frame lol. Keep it up man!

@kingofpaint4676 Жыл бұрын

Job well done, I have watched many videos of bumper fabrication, you are the first I have seen fit the winch inside the grill very creative.😎

@autobotsvsdecepticons9165 10 ай бұрын

Great work man, and you did it in the dirt!

@zandersbailey6546 Жыл бұрын

It always means so much when it's for someone you care about. It seems like it brings out the best in us.

@DirtGarage Жыл бұрын

Absolutely!

@gyffjogofl7676 6 ай бұрын

My favorite part is the bush beer template. Hell yeah

@john316transportllc Жыл бұрын

This is insane good simple build very cool bumper that I have see probably. Congrats you are simply a artist my friend thank for sharing your knowledge you might get me inspired to build one myself. Thank you

@natbarr Жыл бұрын

Nice man! Love your energy!

@curtissheppard1996 4 ай бұрын

Great job man.

@johnnybodangus2529 Жыл бұрын

Looking good man!! I just picked up some 1/4" plate yesterday to make a winch bumper for my pathfinder, freakin stoked!

@DirtGarage Жыл бұрын

Right on!

@Walkeranz Жыл бұрын

Nice work!

@RIDDYxMUSICH Жыл бұрын

Awesome work. Looks tough.

@x5or 6 ай бұрын

Great and Lovely work mate 👏 I also built my own one posted few weeks ago but differently

@davidoverton2432 12 күн бұрын

I like the shape looks good box in the wings to make it easier to clean

@jennifergreene1983 Жыл бұрын

Love it!! Great job!

@DirtGarage Жыл бұрын

Thank you! Cheers!

@JeffAdairKTM530 Жыл бұрын

Great job brother

@obedevert28 Жыл бұрын

Excellent craftmanship.

@DirtGarage Жыл бұрын

Thanks!

@PLUTON9475 Жыл бұрын

Amaizing 😍

@triedandtrue1820 Жыл бұрын

Always watch your vids, preventing me from selling my 99 runner, lol. Good work 👏

@DirtGarage Жыл бұрын

Thank you! I would keep it for sure!

@chevycoloradoinalaska7018 Жыл бұрын

Awesome! Looks great!

@DirtGarage Жыл бұрын

Thanks!

@kingtut5923 Жыл бұрын

Yahoo wonderful , I always wanted one like that , I am 76 and I will do that for my truck.

@CoolPhoenix15 Жыл бұрын

Great job man!

@DirtGarage Жыл бұрын

Thank you! Cheers!

@NN-cw9rb 8 ай бұрын

definitely would've assumed you bought it. looks awesome man. If you get that painted it's going to look even better. I wish my wife let me do things like that to her ride. luck guy right there.

@btxboom8061 Жыл бұрын

Good job AL BUNDY 😄😄

@raminzarea5131 Жыл бұрын

Excellent & Very Good 👌🏻😍

@dominofive5075 Жыл бұрын

You're on a whole-nutha-level bro! I'm building an overlanding honda odyssey🤣 and repainting it with raptor liner. Might be something you'd like to consider for the 4runner 👍🏻

@DirtGarage Жыл бұрын

Thank you! The bumper will be texture coated when its done!

@cardboardkiller6883 3 ай бұрын

Looks good, once you grind the booger welds off and paint it, it'll look as good as any $1,000+ bumper out there. Love it

@irondyne81 Жыл бұрын

Took inspiration off this and basically piggy backed your idea. Don't have pictures to show. Thank you for the idea, cheers.

@salimbenyahia8626 Жыл бұрын

Hello, any plans or tips to build bumper for toyota land cruiser prado 2009/2011 ? Thank you

@EngiTrek Жыл бұрын

Pretty neat! I used to use similar glasses to use with a cutoff wheel, until I got a metal shard in my eye. I have since switched to a full hood. Much better than the trip to the ER, and I think it actually is more comfortable to work with.

@DirtGarage Жыл бұрын

Oh I know, I've got a few slivers in the eye with glasses. Hood would defiantly be ideal

@theford302 Жыл бұрын

you guys don't use saftey squints?

@kevinmiller8265 8 ай бұрын

Do you know where I can get the tiny hole saw that dr. Stranger would use to drill a hole in my eyeball to extract some tiny alien camera . Maybe it was wood I'm not sure any one knows .

@TACOMASRT5 Жыл бұрын

What connecting rods do you recommend as an upgrade for a 5vz? Machined 1uz H beams?

@Bluecollar780 Жыл бұрын

I have the same grinder

@is300bros 21 күн бұрын

you almost lost me when you said C.A.D. 😂

@glennhobbs59 Жыл бұрын

Looks awesome

@DirtGarage Жыл бұрын

Thank you!

@gamer78full 3 ай бұрын

Love the video. I need to make a bumper for my gfs rodeo because she’s really asking me for one 😂

@henrydando 8 ай бұрын

I think i might make something like this for my 97 land cruiser prado. Swap it out for the factory one when i go offroad, and run the factory one the rest of the time

@freeidaho-videos 3 ай бұрын

Buy, beg, borrow or steal a table or bench to work on. Your future self will salute you.

@nopartsgarage6691 Жыл бұрын

The bumper turned out great. Inexpensive too.

@DirtGarage Жыл бұрын

Thank you!

@eddieo7660 4 ай бұрын

I don't know why the algorithm gods put this video upon me whilst on the john but I'm grateful, I had no desire to make a bumper, but now... seems like I have a pretty cool project ahead of me this weekend! 🤙🤙

@cardboardkiller6883 3 ай бұрын

Bed frame angle iron may not be a bad idea to weld up to the inside of your bumper. It's something that I have planned for my build....

@mamatronic963 Жыл бұрын

Mint!!!!!!!!!!1

@boisebiker4713 Жыл бұрын

now it just needs some raptor liner!

@Wdiedericks 4 ай бұрын

Looks good to me. Make do with what you've got. 👍

@nicholaspolhamus9228 2 ай бұрын

hey welder here, love the bumper, you should look into getting a MIG setup for these kind of projects. they go by much faster and you get cleaner welds

@DirtGarage 2 ай бұрын

I MIG all the time, I decided to try stick on this just for fun to learn it.

@Grey-Troll Ай бұрын

Maybe a wire welder with flux core out in the wind like that... not with gas though! It'd be a booger-weld machine.

@carsonspeedster149 Жыл бұрын

Ooooooh is that a yamaha DT I see in the background??

@ChuckUnderFire Жыл бұрын

I’d just cut out those two notched fins in the grill. It’d give it a nice finished look. That said, this is hands down the best, most realistic, and comprehensive bumper build I’ve seen to date. Excellent work.

@DirtGarage Жыл бұрын

I'm gonna wait and see what the actual winch is like in it, before I cut away the grill.

@Redneck_Technophile Жыл бұрын

1:43 NYOOOOOOOM

@nulcable Жыл бұрын

eyecrometer! Ahha hilarious. Bumper looks great. Better get those scissors ✂️ back to Mrs dirtgarage Pronto!

@DirtGarage Жыл бұрын

Haha! They are returned

@shagnasty6391 7 ай бұрын

It would be difficult for me to build a bumper like that.. I prefer to lay it all out on the table. Put it together, paint it, then attach it and make it sturdy... af...This guy did a great job and he sourced all the materials for near nothing... even greater job.. keep at it and you'll have to buy a welding fab truck.... 😊..also, i have plans for my 98 sr5 4x4 2.7 ... 2JZ.. maybe?

@welderse14 Жыл бұрын

Nice work.. Amazing how much "upcycling" of metal gets used from the local dump.. What kind of hole you gonna cut in the front plate? Roller fairlead or rub lead?

@DirtGarage Жыл бұрын

Getting synthetic line, so rub lead. Don't have it yet, otherwise I would have cut it in already

@michaelwinter9733 Жыл бұрын

Try using atf mixed with acetone for cutting oil

@DirtGarage Жыл бұрын

Haha WD was just there and convenient

@dandahermitseals5582 Жыл бұрын

Shoulda just scribed the cut off line of corner piece shallow to just fold it and back weld it

@RastusMcbride Жыл бұрын

Mighty fine 60$ bumper. You should make those "cad" templates put in them in a box and sell them for, I don't know $. I'll take one ;)

@lawcodynw30 Жыл бұрын

Aye man good job like your style ! What’s the link on this exact welder I don’t want to get the wrong vevor! Keep it up buddy !

@DirtGarage Жыл бұрын

bit.ly/3osSr6v and added discount code in description!

@parker6334 Жыл бұрын

Cover your radiator/t cooler when your welding so close to it.

@DirtGarage Жыл бұрын

Nah

@MrClubeg6 Жыл бұрын

Aw man I was hoping for that first gen taco front on it looks so bitchen with the lines

@DirtGarage Жыл бұрын

If I was able to find a 1st gen taco front end I would have swapped it!

@CB-hr6zs Жыл бұрын

Shop lion on the prowl at 1:44

@crazgreek Жыл бұрын

Look into primeweld and teach yourself how to tig. Ditch that stick welder. You'll Thank me

@autodidacticartisan Жыл бұрын

I have some of those exact same pieces of scrap metal that came off a modular home we were demolishing

@DirtGarage Жыл бұрын

I was told that's what they where from 🤣

@autodidacticartisan Жыл бұрын

@@DirtGarage the funny thing is that I was already planning on using them for a bumper on my 85 toyota! Seriously a crazy coincidence

@jfloydsea Жыл бұрын

Great looking bumper! Is that welder 120 or 240?

@DirtGarage Жыл бұрын

Both, I used it at 120 here though

@clamboni9 Жыл бұрын

lol the cat

@haizi7179 3 ай бұрын

1:43 Cat spotted

@CB-hr6zs Жыл бұрын

Since you started this 4Runner series it makes me want to fix up my second gen 4Runner and not sell it

@allenwilson9656 Жыл бұрын

You might want to cut out a hole in the bumper for your fairlead to let the winch line go thru ! Also why didn't you cover the lower part of the factory mount with some more metal pieces ? 🤔 you should also use cutting oil or motor oil instead of WD40 when you drill holes just a few ideas 💡

@DirtGarage Жыл бұрын

As mentioned its not done yet, gonna be lots more bracing added, also don't have the winch / fairlead yet, so I don't know where I want to put the holes for fairlead. WD was jus there and easy.

@LifeTimeDreams51 Жыл бұрын

🥇

@clayton203 Жыл бұрын

You out did me when you broke the scissors and cardboard out, Still the best way to go, A person saves a ton of money doing it yourself Nice fabrication

@deadgameguns Жыл бұрын

nice! looks post apocalyptic!

@DirtGarage Жыл бұрын

Thanks! It will be sanded down and painted. But for now the rustic look is neat haha

@nemesis851_ Жыл бұрын

Praying the incoming winch doesn't require more space to operate

@kenstricklin1233 5 ай бұрын

Good work, but the welding amps should have been higher. I would have stuck with a process you already knew. It's really important to know your welds are good. Of this comes apart while winching, someone could get hurt. The bumper looks good. I just question the quality of the welds. I will subscribe and keep watching. Fab on. K.O.R.E.

@Username72589 Жыл бұрын

Really need to wear safety glasses when cutting or drilling and grinding!!!

@heavymonty Жыл бұрын

does the 125 in the background run?

@DirtGarage Жыл бұрын

Yup! Ripped it apart and did a resto on it this spring, was my project before the 4Runner. Street legal 84 DT125.

@heavymonty Жыл бұрын

@@DirtGarage i want a steel tank enduro so bad.

@ConSeann3ry Жыл бұрын

Damn with that Mullet you are really growing stronger and becoming full form of guy-with-engines-in-his-front-yard lol. Not hating it's me too without cool hair 😛

@DirtGarage Жыл бұрын

Actually just took the motor out of my yard and brought it to dump last week! Haha

@ConSeann3ry Жыл бұрын

@@DirtGarage hahah must be to make room for another!

@TyScott85 Жыл бұрын

Where is Julian and Bubbles?

@tommcl8548 Жыл бұрын

👍👊

@fornammefternamn6724 10 ай бұрын

looks good. but using wd40 for drilling holes, damages the drill ant takes longer time. get some real cut and cool fluid on the store, its is not expensive and you will notice the difference

@nemesis851_ Жыл бұрын

Alternate video title: Installed fenders in 5 seconds

@DirtGarage Жыл бұрын

Only got 1 out of 8 bolts haha

@drewfleming7065 Жыл бұрын

You know the rules...you weld on youtube...ya have to show close up of the finished bead...LOL Nice design!!!

@DirtGarage Жыл бұрын

Haha, I'll pass. Definitely needs a little grinding! Maybe when I get more comfortable with the stick, if I chose to use it again. I think I like MIG more..

@drewfleming7065 Жыл бұрын

@@DirtGarage I just replaced a cheap mig with a cheap mig from harbor fright $215. Light weight 15lbs, good control of watts and wire speed, titanium brand...Lays a nice bead and Im the worlds worst welder....I do find that wire brand is important....harbor frieghts wire is not great, maybe dirty? Lincoln is best get it at home depot. Keep the vids coming, love your enthusiasm.....

@drewfleming7065 Жыл бұрын

Also I like you hate the wheel of death grinder...When I have to make a long straight cut I prefer a skill saw (circular saw) with a metal blade...much safer and can get a straighter cut....

@jameshuggins4300 Жыл бұрын

Not dogging your build but... what are you gonna do with subframe that is sticking out?

@DirtGarage Жыл бұрын

It's just the factory bumper brace thing, gonna cut it out, and make a piece to match up to skidplate.

@jameshuggins4300 Жыл бұрын

@@DirtGarage cool thanks! Done right and you could get a kinda prerunner look to it. 👍

@charlestonbrown9161 Жыл бұрын

No one gonna consider the random cat? 🤣

@pebblehilllane Жыл бұрын

The black cat was for good luck. Black cats are always good luck in spite of what has been said about them by some.

@makeitpay8241 Жыл бұрын

your headlights do not like it when you weld near them.

@DirtGarage Жыл бұрын

Nah, they are fine

@johnathanreigard512 8 ай бұрын

If you don’t paint that lol

@dandahermitseals5582 Жыл бұрын

That is gonna block the air flow to the radiator of an infamous overheating engine. Bad idea . Dandahermit

@DirtGarage Жыл бұрын

Nope! Lots of airflow. I've also used much smaller rads with no shroud in 3.4 swaps in other vehicles. 3.4s don't have a overheating issue.

@dandahermitseals5582 Жыл бұрын

Poor Toyota

@dandahermitseals5582 Жыл бұрын

You are totally blocking all the possible air flow to your radiator.

@zdavidzz 8 ай бұрын

Now just add some spikes to the front