With a bar that long you don’t even have to leave the house to to cut wood lol

Those rounds you cut first would make an awesome naturally finished electric guitar body, they were beautifully patterned...

Good video Sye!! I also have one of them. Love it so far. A little tip. When you are pouring bar oil from that type of a jug. Pour it from the side not the end. the handle doesn't get in the way. It's easier to not run it over.

I had a friend from Sweden who used a 60 in.bar on an MS 660 & 72 in. bar on his MS 880 but to me that 36 in bar looked huge compared to the 20 in. bars I used all the time and only used a bigger bar then a 28 in bar once - a (48 in.) bar once at a competition and it scared the hell out of me but I played tuff and wrestled through it . : )

Gotta Love A Good Deal when it comes along ! " Merry Christmas " From Canada ATB T God Bless

Now with that bar on there you could really call it the blue beast!! Sheesh!

Dude that saw is massive and awesome!

OK, did you see the spalting on that log? You had a ripping chain! Stand it on end and save that beauty! Whew! He did... just when the tears were starting to flow.

Hello from ireland. Love your videos

Wonderful video! May just order me one.

Another great video...thx for sharing

I like it. I've got to get me one of those 660.

I like the color a lot.

Late to the game here, but a tip: Oil the bar groove top and bottom generously when installing new or new chain. If dry, the initial few seconds of wear will be great.

That Chainsaw looks really well balanced with that bar on it & looks to cut like a really PO"d Beaver ! : ) : ) I love to have have a tiny piece of that Maple for knife scales it sure is purrty!! : )

The good news is parts off the Stihl 066 fits on these saws perfectly. I swapped out my pull start housing (which on the 660 is very generic) with an old 066 I had layin around.

Yeah I think some packing peanuts would be a big help. Just received my G388 and the chain break handle was broken. Runs great the chain tensioner is sketchy. I wrote their service an email now just waiting for replacement.

yo unck that saw is sick gonna get one

I like the full wrap bar on those

I received a G660 Chainsaw like this directly from Farmertec one week after ordering it and quickly unboxed it and it soon became apparent that it was not providing enough oil to the 36 inch Farmertec bar & Chain I purchased it with. I E-mailed the service dept. of Farmertec and they said it was probably a bad oil pump and offered to send me a replacement oil pump. I stated that they should send me another saw that worked out of the box and they refused and would not pay to install the new oil pump in the saw. So effectively no Warranty even for units defective out of the box! Then I tried another bar to see if it was a bad bar and the saw seized up. So next I asked them if they had a warranty station anywhere in the US and they said no. So buyer beware they do not know what a warranty is and if its bad out of the box-tough- they will send you parts so you can pay for repairs to a brand new saw!!!!

Absolutely love looks of this saw.

Love my blue thunder

Hopefully as these Chinese companies progress they will learn to spend a few cents more for better packing on international shipments. I bought one saw from hutzl and one from another Chinese company. Both boxes looked like they had been kicked down the interstate. And for some reason on both of them the only thing broken was the small screwdriver handle. Those things must be made of Austrian crystal!

That 8 pin rim sprocket seems to be holding that saw back, it should have a lot more to offer.

Looks like OVERNIGHT shipped that one. I used to do shipping and receiving. Hard to find a good fast shipper. OVERNIGHT always delivered in pieces.

How do you like those laser bars and chains? Thinking about picking up the 28".

Uncle another great video we appreciate your time. How much did you end up paying for the saw, it's a beast I really considering picking one up

Wow! Awesome saw! What were you saying about the 404 pitch chain? I have a nearly new bar and chain. Fits 08 stihl and other large body stihl saws but no saw for it. The 880 is the only new stihl that would take it . Too expensive for what I want to do. I turned my 08(S) into a cut off saw.

Hello, what are the factory settings of the holzfforma g660 carburettor. - because it doesn't work on those in the operating instructions

Thanks for the video. Question: I saw on another comment you were using a 3/8" .050" chain. Is that bar the Laser 41198? Thanks.

My new G660 showed up too. Some issues. The throttle linkage worked initially, now there is no response when it is blipped. The chain oil dumped a ton of oil on to the clutch and the antikick back bar no longer stops the saw. Any thoughts?

Your a VIP Customer!

You got any advice for trouble starting up a G660 brand new out of box? I'm a bit new to gas powered chainsaws... the few electric ones I've had just go at push of button, but after seeing one of your video's on milling wood I knew I needed a powerful chainsaw and maybe I just don't know the starting procedures... tried to follow along by the book, but maybe I'm missing something and I ended up flooding it. Any help would be greatly appreciated either by you or any of your followers! Thanks in advanced.

Mine wouldn't run after a year so I got an oem Tillitson carb and it runs good again but the idle tuning changes from day to day, rich or lean, any ideas?

I got a holzfforma g 660. The first time I tried to started it it sounded like it was about to start for second but didn't. That was the closest it got to starting after 30 minutes more of attempts. A few days later I tried again with the same results. A few days tried for the third time. Nothing. I had a neighbor help the following week and he got it going. After 5 minutes of running it started to sound like it wax running out gas and it died. It had plenty of gas. As it cooled and I tried to pull the starter chord got it got harder and finally jammed. Pulled off the starter cage and it was about to fine. the fly wheel was stuck but was able get it to move .looked online and an article said to put oil in cylinder and let it sit for a few days. After two more days I moved then piston and was moving. Today I tried and it would not move at all. Does it sound like the engine is seized? Can't seem to find a way to contact the company. Anyone know how to contact the company?

Wow that 36" bar looks soo long.I was cutting some big ash rounds with a 28" bar with a stihl ms 460 . Not used to that stuck tip in dirt. Guess those long bars are for guys out west

Over all is holtzfforma worth buying? Was thinking g372xp never had a chainsaw before

That's how you warm up a 2 stroke.

Hey man good video 👍 but please they are log dogs not bumper spikes.

What changed your mind about the 070?

What is the mix of fuel you used? was it 50:1 or 25:1?

Were can i order one of these saws? How much total all to get it to me. Saw 28inch bar. To springfield mo.

I just purchased the Yuzhoukee YZ105. It fired up fine butthe chain isn't turning. I took the bar off, and sprocket turns. Should I adjust the chain a little looser and try again? I don't want to take the clutch off if I don't need to. HELP. I need to mill 200 black locust cookies ranging from 30 in. to 40 in. in diameter.

Hi uncle cy Can you recommend the G660? Thanks for answer

packaging has always been a little "iffy" on a lot of the chinese stuff I buy. I have to wonder how much money they waste due to damaged parts? For the saw, a molded foam encasement would be just the ticket to insure freedom of shipping damage.

Anyone know what the life span or reliability is on the G660?

Have you invested any serious work hours into that saw yet? I'm looking for a powerful saw for milling as well, but due to a fixed income I cannot afford to buy a Stihl or Husqvarna.. I appreciate any info you can provide. Thank you and God bless!

Had to carve out a little section on my farmertec 660 so the handle would full engage the brake mine had to go well past the muffler.

I have the g72. Still won't start. On my 2nd carb. And now the pull handle is starting to stick. Thinking buying cheap was more expensive

Man that packaging is rough...

Daya tahan ny gmna om??bagus g sinso china

I just got my g660 n having a hard time starting it..keep flooding it..frustrating..any tips

Is this a common occurrence with delivery?.?.? Need to know.... thanks

Where can I get a 42" bar to fit this saw?

do you use 3/8 .50 chain on those?

What oil ratio are you using diy with Uncle cy

i just got a g660 at a auction i need to replace the chain tensioner have a vido

Will that saw accept an Oregon etc bar?

Where can we find that 36" bar & chain at ?

Would it work to cut up a body ?

Где можно такую пилу заказать? Где вы ее покупали?

Hi, I noticed the handle is a bit different than the normal one, like it goes over the right side of the chainsaw too, when usually they hast have it on the left one because when you saw you flip the chainsaw over its right side for cutting and then you handle it with the left, so I wonder, what is the purpose of that handle that goes over the right side as well?

Wow... AAA+++

How many cc's engine.

She throws the noodles all right

Bought a g444 and have had nothing but problems.waist of my hard earned money.Ill stick with my old mac's 50years old and no problems. At least I can count on it to do its job. what a rip off.

The logger boys, tell me that the plastic parts R kinda shity, if U use em hard throw em around or they get swatted. The pull starter housings and inner parts take a beating 2, so they swap em out for Stihl OEM pts. So I guess U kinda get watcha pay fer, A?

36" Paris