Not negative comment, but you miss the most difficult component is changing new arms to remove the arm-shaft-spring-axis. There are four screws inside that must be removed using a 90-degree screwdriver.

Ughhh the only thing you forgot was the legs. The legs are the most commonly damaged/replaced part

This officially makes ya a legend, mate! Thanks for the tips. Now doing maintenance on my Mavic 3 Pro is no longer stressful. I am a fairly new owner but LONG time creator. This is Very appreciate good sir! GREAT work! \m/

Tremendo trabajo gracias por compartir

we need a tutorial on mavic 3 pro please

Perfectly made! You are Great!

Handling would be so much easier without the props !

Hello, excellent video, one question, I replaced a visual sensor on my Mavic 3, but now I get "calibration error" how can I solve that?

Very good video

Very interesting. Maybe you have already opened the DJI Charging hub ? Is it screwed or with clips ? Patrick

Great video.

hola. segui tus pasos y cmbie los sensores delanteros. pero como los calibro.

Hello my friend, thanks for the video. But it's still missing how to change the middle shell. The plastic got hard because I use it most of the time in the sun, and when I opened the wings, the connection on the middle shell just got broken. Please help continuing the disassemble!

How would I replace the front top sensor?

So, when I opened the front left motor arm, the middle shell just got broken... So, I have to order a middle frame, everything else on the drone is perfect, but I CAN'T find anywhere else how to disassemble all parts to replace the shell. Best regards and thanks!

Hello bro, 'am a new ur subscriber. A whole of urs vids are great! Keep it great, and hella pleased to found those channel. How a ultimate tutorial and perfect guide. Thanks

Say my guy what about the legs u started with the white wire

Anyone have a video on only replacing the landing legs without having to disassemble the whole drone ...I'm sure less steps are needed then in this bideo

Hello Can I disassemble mavic 2 with this video??

How do you get the 4 screws out for each of the rear arms? I've tried with a 90°ratchet and can't do it. Ugh!!! What's the trick?

Great video. Thank you so much for the guide. Couple questions. 1 - do you have a diagram showing what each ribbon cable and ufl antenna connections are for? 2 - how is the motherboard powered? Is it from the speed controller board through a ribbon cable or through a pin connection. Looking at how to use the motherboard and camera not with the drone itself.

Exemplary video. As much as I appreciate your work.......merely changing the ND filters on the M3 can be enough to bring me near a panic attack. It really feels like the pressure on the gimbal is nearing too much and I'm surprised that a simpler mechanism wasn't used (magnets?).

Hello everybody, I’ve crashed my mavic 3 cine and wanted to know if I could repair it by myself or it needs to be fixed at dji official center ? Does it require any programming after replacing new parts . Thank you

Definitely subscribing great content. 🙏🏻 have a question the first top frame body square you removed I couldn’t see if the usb type c port/micro sd card slot is accessible at that point.

hello friend I have a mavic 3 classic and when I make an orbit movement it loses the horizon little by little, do you have any idea what it could be? I've done all possible calibrations on it

The cover with the button and leds of one of my batteries broke off and tore the ribbon cable. Do you think there's anyway of finding that part and replacing it or is it not salvageable.

where can I find back replacement shells??

hello, what processor is used in this drone and where can i read about it?

Mine has a screw with a ball point on it for the body? Not sure how to take that off

Only piece im seeking to replace is at 4:19 what tool do i need?

How can one calibrate Mavic 3 gimbal, when the system is not reading the drone even with DJI Assistant 2? Please help

Can the cable signal of the camera be replaced ?

It's usually not a great idea to reuse thermal paste. Good video otherwise thanks

At this point I’m loss 😂😄👍🙌💪💪

Can I contact you via Facebook or the Internet?