thank's for the interest from this experiment, this is for a quick test to make conclution, my opinion from this test is..if i use original li-ion battery (not fake cheap like this) and if we can set the minimum voltage for the battery on the P3S to for example 3v, i believe it can fly more than 30 minutes easy

Though lithium is absolutly volatile and can be dangerous as heck... its not a piece of dynamite. many many many people diy lithium power walls to power their house. If doing something like that never crossed your mind before reading this... then yiou are not the type of person who should be doing that type of thing lol

Thanks mate, oh this is a hobby that is not cheap, I want to help people with limited funds (like me) not to be discouraged, there are always many ways for us to survive, even if it's a little ridiculous way but the important thing is that it works 🙂

ah ah! i know someone will read my mind sadly we can't, the position of this gimbal was upside down is just perfect to put under the belly and i only have one plane with landing gear (skywalker) but we are far for now 😓

@@benznote2342 I've wanted to put a F16 Falcon like Tricycle landing gear on my Reptile Harrier? Or maybe suspend it on the fore deck of the Binary?

@@spartan3299 attaching the landing gear is only suitable for a tractor or pusher engine but with the propeller position on top (similar to a skywalker), I don't understand how you would fly it for a harrier without scratching the propellers into the ground 🙄

ah you so kind, thank you ☺

for charging cycles endurance converting to li-ion you're right JD is a good deal, but if we look at it from weight to flight time ratio not worth it for this phantom 3 (same as stock battery), too much pulling amp and li-ion is not happy with that

i'm using CP2112 method, you can search the howto from google there are plenty people using it, but carefull you also need to know what version bmc from the pcb of battery because not all can be unlock (only the old version) i'm forgot which one because this is a long time a go

thank you a lot!!@@benznote2342

Я делал односекундное короткое замыкание на MOSFET каждый раз при запуске (активировал питание от BCM). как я сделал с другим умным аккумулятором kzfaq.info/get/bejne/qN2Enc97sZu6Y6M.html может быть, неплохая идея ... этот эксперимент не потому, что он терпит неудачу, а скорее потому, что FC заставляет его приземлиться, потому что ПРЕДУПРЕЖДЕНИЕ О НИЗКОМ НАПРЯЖЕНИИ все еще использует стандартную липосакцию, на литий-ионе на самом деле все еще много энергии.

@@benznote2342 Да я об этом не подумал. Так как програмным способом нельзя это изменить. А вот для phantom 2 можно. Там в ассистент есть такая функция. Она не разрешает садиться при якобы низком заряде аккумулятлра. Кстати для размышления: в неоригинальных аккумуляторах phantom 3 применяют lipo а не lihv. Ее плата bms похоже обманывает полетный контроллер так как lipo имеет заряд ниже. Если у Вас все получится, то Вы первый кто это сделает.

@@benznote2342 Please forgive my stupidity. How did you activate the MOSFET of the lithium battery? Can you share the specific steps and the power supply location during activation? It is said that the battery of the P3 series cannot be permanently unlocked through software, right? If so, this battery-activated solution may be ideal for you. In addition, after activating battery power according to your method, will the communication between the smart battery and the drone also be available? For example, transmitting single cell voltage, temperature and other parameters to the drone. I have a P3A, and one of the batteries has experienced serious degradation. I plan to replace it with a set of large-capacity batteries and hang it on the tripod. Please feel free to enlighten me. As a keen DIY enthusiast, I am willing to take risks to gain new knowledge and skills, they are so fascinating. Thank you so much!😊

of course we can the capacity will increase but carefull the c rate will be follow from the lowest

the intelligent battery board is actually locked, I activated the mosfet by jumping it, the method is more or less the same as in this video kzfaq.info/get/bejne/qN2Enc97sZu6Y6M.html but i'm so sorry I didn't share how to do it because I consider it an irresponsible act 😪

lhooo ini orang indo toh, pke ingris"an segala weleh 😬

Sumuhun, orang bandung, tos lami abi ngfans teh, xixixii

​@@benznote2342haduhh kirain ytbnya orang luar pas baca baca ternyata 1negara.mantap om