Do it yourself brake cable repair

No video

Do it yourself brake cable repair

Рет қаралды 85,066

Күн бұрын

ear wire head can be used for throttle cable, brake cable, gear cable It is easy to make and install. the whole wire does not need to come out.
music • Arp Bounce - Geographe...
#throttle #cables #cablerepair #broken #brokencable #clutchcable #brokencable #clutchcable #bicycle
00:00:00 Brake Cable replacement free
0:29 steel screw lasts longer
0:43 how to drill the cut screw
1:28 in this hole I will put the wire

Пікірлер: 33

@johngranato2673 3 ай бұрын

Done the same and added Red Thread Locker--after cleaning cable end, set screw, and end-piece with carb-cleaner (and let dry for a few minutes).

@michaelbarton7295 8 ай бұрын

I have done almost exactly the same thing with a car accelerator cable, even down to the M4 tap and the grub screw, and I thought I was the only one to think of this, so good for you!

@MBPATENTS 8 ай бұрын

Hi michael Well done, congratulations as always

@andythehaymaker 11 ай бұрын

Ooh I like this!

@MBPATENTS 11 ай бұрын

Thank you very much!

@Insignificatos Жыл бұрын

Awesome job! Well done and thankyou for the Tips

@MBPATENTS Жыл бұрын

Thank you very much for your kind words!!!

@jeeko92 5 ай бұрын

Buying this tools is more expensive than the cable itself

@MBPATENTS 5 ай бұрын

Then you can buy a cable

@sumithpriyantha1212 2 жыл бұрын

Great thanks

@monstercolorfunco4391 Жыл бұрын

it's dangerous what he did because the metal gets fatigue stress once it's pinched like that, it will start to fray and cut slowly at the point where it is pinched... A few thousand brake movements and it will just come loose by surprise. The point with solder is that it holds all the strands and can (ideally) prevent the pinch stress completely by developing all the cable.

@creative7981 Ай бұрын

@LaurieFloodTeacher 2 жыл бұрын

Thank you! You are my absolute hero! I'm surprised more people haven't commented on this video. I'm somewhere where it's not convenient to try to fabricate something with solder. This is much simpler. Thank you a million times.

@MBPATENTS 2 жыл бұрын

Hello Laurie Flood, thank you very much for your kind words. !!!!!😀

@MBPATENTS 2 жыл бұрын

m.kzfaq.info/get/bejne/pa5la7CbvcfFXZc.html Here it is a little simpler

@monstercolorfunco4391 Жыл бұрын

Well, it's dangerous what he did because the metal gets fatigue stress once it's pinched like that, it will start to fray and cut slowly at the point where it is pinched... A few thousand brake movements and it will just come loose by surprise. The point with solder is that it holds all the strands and can (ideally) prevent the pinch stress completely by developing all the cable.

@dalepaladin916 Жыл бұрын

You must be one of his relatives

@monstercolorfunco4391 Жыл бұрын

I still think that it would be better to dip it in hot solder metal

@MBPATENTS Жыл бұрын

if you have the right tools, do it and tell me if it works for you or not because I've tried it. everyone does the same thing i said to do something different.

@ericputian975 2 жыл бұрын

Rather to buy new cable break than buying that expensive tools...

@MBPATENTS 2 жыл бұрын

you make two staples and you have them in time of need until the health weekend that is all closed You can wait or this is your opinion Thank you for your interest!!!

@LaurieFloodTeacher 2 жыл бұрын

Not all of us have that option. Maybe you don't have a prefabricated tool for the use case. On a bicycle, it's a different story. I am looking at my throttle cable.

@MBPATENTS 2 жыл бұрын

Laurie υπάρχουν πολύ τρόποι να φτιάξεις μια ντιζα ανάλογα με το τι σχήμα έχει τα φτιαχνω για ώρα ανάγκης παράδειγμα μου κοβεις ι ντιζα στο δρομο σε 2 λεπτα το εχου φτιάξει και κανω τι δουλειά μου άνετα το σαββατοκύριακο είναι όλα κλειστά δεν μπορώ να αγοράσω ντιζα τοποθετώ ενα ανταπτορα και ολα ειναι πολυ απλα!!! Έχω βάλει πριν 2 χρόνια δεν έχω κοπή ακόμα lol

@monstercolorfunco4391 Жыл бұрын

the pinch point of the repair can fray and crack more easily that a pro cable after 1000-2000 repetitions, for a life-death equipment, it's not the wisest. you will see that cables are always designed to have no pinches or bends, only crimps and welds, to avoid risking lives. If he did that first and then welded it would be ok.

@thehumancrumb.668 4 ай бұрын

Brake not break

@michelkwort3832 Ай бұрын

It is good for a throttle cable BUT no secure for a brake or clutch cable ant such système exist in all good meca supplier !?!?

@MBPATENTS 21 күн бұрын

Hi Michel if you treat it well it doesn't hurt anything if you put a thicker wire and pinch a bit in front with electric welding to make it thicker or not go away and the screw grips the cable well there is a chance that it will last for an animal and never get hurt

@gelo207 Жыл бұрын

DIY? 😂😂 you know what that means or no

@MBPATENTS Жыл бұрын

I know. But I don't think you do as it seems.

@jasondougal3438 Жыл бұрын

@@MBPATENTS 🤦‍♂️bro ! The title of this dumb fucking video is “ hot to change break cable with minimum tools. 😂 you think I have a whole metal shop on my bike. Dumb fuck!

@dalepaladin916 Жыл бұрын

I think he thinks that it is DIY and a master's degree