Does Anti-Seize Compound Actually Work? Let's find out! Anti-Seize vs Grease vs Fluid Film vs Wax

Рет қаралды 2,808,103

Күн бұрын

Does Anti-Seize compound and lubricant actually work better than other options such as grease, fluid film, or candle wax? Does it work better than using nothing at all? Copper, nickel, and aluminum anti-seize lubricant compared to bearing grease, Fluid Film, candle wax, and using nothing at all. All products tested for rust stopping or rust blocking, extreme temperature tolerance, water resistance, and even as an engine oil substitute to provide permanent protection against engine seizure.
➡ Thank you very much for supporting the channel: / projectfarm
➡ An easy way to find past videos along with products tested: bit.ly/2FCrBpk A big thanks to Jim for putting this together.
➡ Merch: www.Project-Farm.com
➡ Click here if you'd like to subscribe: / @projectfarm
➡ As an Amazon Associate I earn from qualifying purchases.
➡ Products Tested In This Video (in no particular order):
Permatex Aluminum Anti-Seize: amzn.to/34muTaQ
Loctite Copper-based Anti-Seize: amzn.to/2Ep8bDU
Nickel-Graf: amzn.to/32hL5aH
Candle: amzn.to/3hkUQez
LubriMatic High Temperature Grease: amzn.to/3j7v3ad
Videography Equipment:
Sony DSC-RX10 III Cyber-shot Digital Still Camera: amzn.to/2YdXvPw
Canon 70D Camera: amzn.to/31b5Gy0
Azden Microphone: amzn.to/34d3DLE
Go Pro Bundle: amzn.to/31aince
This video is only for entertainment purposes. If you rely on the information portrayed in this video, you assume the responsibility for the results. Project Farm LLC

Пікірлер: 12 000

@ProjectFarm 3 жыл бұрын

Products Tested In This Video (in no particular order): Permatex Aluminum Anti-Seize: amzn.to/34muTaQ Loctite Copper-based Anti-Seize: amzn.to/2Ep8bDU Nickel-Graf: amzn.to/32hL5aH Candle: amzn.to/3hkUQez LubriMatic High Temperature Grease: amzn.to/3j7v3ad

@bobthompson4319 3 жыл бұрын

Does it conform to the sn rating for motor oil? Lol

@rebel04343 3 жыл бұрын

Should test fluid film as a motor oil!

@proweyz 3 жыл бұрын

I know a mechanic that use engine oil. Can you do a test on engine oil as well?

@jamc666 3 жыл бұрын

I would argue that the candle would'^ve done a better job if it wasnt cooked away prior ....

@intellectualiconoclasm3264 3 жыл бұрын

I honestly didn't see the engine coming apart for that reason. I figured it would be too viscous and cause to much strain. Now you have me curious about these products for polishing or lapping abrasives.

@keldeweese7637 4 жыл бұрын

I’m just impressed that he and his shop weren’t coated in anti seize by the end of this. Anytime I touch it, it magically gets everywhere.

@ProjectFarm 4 жыл бұрын

lol That would have been a problem!

@shaggydaboy2 4 жыл бұрын

Yes. Especially the permatek. That stuff gets EVERYWHERE. Especially when coating wheel hubs with it lol

@woopimagpie 4 жыл бұрын

I know right! No matter how careful I am some always ends up somewhere I don't want it. Dreadful stuff. It does work though, both this video and my own experience has taught me that.

@Markomyt1 4 жыл бұрын

I really go through the gloves cuz I have issues with it.

@KB-ld7jw 4 жыл бұрын

The same thing happens to me. It always gets all over the place.

@RobertMoser 4 жыл бұрын

You need to give a masterclass to all other KZfaq content creators on how to get to the point. Seriously, you cover in fifteen minutes what would take others hours of stretched out yapping to do. Thanks for the work you put in, I genuinely appreciate it!

@ProjectFarm 4 жыл бұрын

Wow, thanks!

@davidzplace2011 4 жыл бұрын

I'll second that, much thanks, and loud clear audio, and to the point, absolutely love that, loud clear audio is actually rare, us truck drivers love that, cause we often listen to vids obviously not watching and audio quality is important

@rodneyharouff5739 4 жыл бұрын

@@ProjectFarm mr. moser is spot on there. yer the best i've seen on here anyplace.

@Arkanic 4 жыл бұрын

Agreed, these videos are excellent. I don't mind a little wandering if it's something I am watching purely for entertainment but for informative stuff this is about as good as it gets.

@s0nnyburnett 4 жыл бұрын

It's a wonderful thing when people don't waste your time.

@jbilletz 2 жыл бұрын

You sir in my opinion have one of the best channels on KZfaq. No loud obnoxious intro music. No watch my dog run around the yard. No incoherent rambling for 10 minutes. No make sure you subscribe and hit the thumbs up button. You are straight to the point with no BS. Keep up the good work.

@ProjectFarm 2 жыл бұрын

Thanks, will do!

@NONAME-kw3pu Жыл бұрын

right to the point

@frankvivone485 Жыл бұрын

I always come away amazed, humored, with increased common sense quickly

@Kgio-2112 Жыл бұрын

Exactly! All the others should take note.

@dannygingerich2360 Жыл бұрын

Notice how the loudness of the video is controlled? Just beautiful. The motor didn't wake up my cat, 🙀😻👌

@eeassa Жыл бұрын

This guy does some of the most thorough and scientific testing. And destroys a lot of lawn mower engines lol!

@ProjectFarm Жыл бұрын

lol Thanks!

@CR4T3Z 3 жыл бұрын

3 months of prep work, the effort you go through to show us a true review of a product. That's insane dedication! Much appreciated for all of your videos

@ProjectFarm 3 жыл бұрын

Thank you!

@the23er 3 жыл бұрын

I do not have any use for that information, but i stay just out of sheer amazement for all that effort put into those tests.

@wachocs16 3 жыл бұрын

I really was impressed when he compared all different brands of lithium AA batteries and came with test samples of 2 years of use

@racker5108 3 жыл бұрын

Yeah I’m frequently blown away from all of his improvised testing methods and his extensive level of detail. True talent dedication here.

@unclematt3 4 жыл бұрын

Not mentioned but relevant: Burgers no longer stick to the grill, and now have a distinctive coppery flavor.

@ProjectFarm 4 жыл бұрын

lol. Nice!

@oneselmo 3 жыл бұрын

unclematt3 Ah no, now you've made me pee myself laughing...

@x-man5056 3 жыл бұрын

Good for sex too. NOT

@Spooky4815 3 жыл бұрын

Copper is poison if inhaled or consumed i think so make sure you clean that grill good.

@Deckzwabber 3 жыл бұрын

That's good against bacteria. A great tip if you like your chicken wings rare.

@gregoryirvine5693 2 жыл бұрын

I worked 41 years in a coal fired steam electric plant. The units were rated for 450 Megawatts. Needless to say we had some massive equipment and valves under a lot of torque and stress. We used a lot of copper based Anti-Seize on a lot of different equipment. I learned my lesson well and I use it a lot on my farm and cattle equipment now in my retirement. I look forward to your products test every week and use your suggestions whenever I get a chance. You do an outstanding job. One of your fans. Thank you.

@ProjectFarm 2 жыл бұрын

Thank you!

@normajohnson6352 Жыл бұрын

YES! 41 years in a coal-fired plant also! Anti-Seize is used in all applications. Nickel and copper, depending on mfr's specs.

@willpestka2745 Жыл бұрын

I work in pump repair for power plants and most plants are converting to using copper-free anti-seize and graphite bearings. Any bronze or copper in the feed water apparently leaches out and can severly damage boilers.

@leislymejia2864 5 ай бұрын

@@normajohnson6352whst brands?

@johnwilcox4078 2 жыл бұрын

Thanks for confirming my faith in Permatex antiseize, I've used it my whole career as an HVAC service technician! A little goes a long way, one bottle lasts for years. New subscriber here from Wisconsin, corrosion protection is very important here in the Upper Midwest! You're making Consumer Reports look like amateurs!

@ProjectFarm 2 жыл бұрын

You are welcome! Thanks for watching and subscribing!

@robertlindsay9826 2 жыл бұрын

On some of the ball mills used in the gold mines, we used aluminum based anti seize on the big bolts that old the steel liners in place. man, give them 3 months, and that stuff acts like glue. Impossible to undo without a huge impact gun. The best is copper based but its expensive

@magicoddeffect 2 жыл бұрын

@@robertlindsay9826 He mentioned in the video that anti-seize can cause galvanic corrosion when used on certain metals, so it's important to pick either the aluminum or copper stuff based on what it's being applied to

@raumfahreturschutze 2 жыл бұрын

>You're making Consumer Reports look like amateurs! that's cause they are lol

@TheLegendBrolySS 2 жыл бұрын

Is it good for ball lube?

@CarlosAnthonyLopez 4 жыл бұрын

Lawn Mowers tremble when this man walks into the store.

@ProjectFarm 4 жыл бұрын

lol Thanks for watching.

@franciswhite419 4 жыл бұрын

Yes. You know who to never lend your mower to.

@Bandicoot803 4 жыл бұрын

One has already written a diary from personal experience!

@GunnysWrenches 4 жыл бұрын

Lol!!! That’s a fact, I think Project Farm is where all bad behaving mowers are sent to be tortured. Ha! Ha!

@theavengers3411 4 жыл бұрын

Project Lawn Mower Torture Chamber. I feel a rebranding is coming up soon.

@GroovesAndLands 4 жыл бұрын

I love the shot of the dipstick showing the crankcase "full" of anti-seize! Lolz

@ProjectFarm 4 жыл бұрын

lol. Nice!

@Pierobon 4 жыл бұрын

@@ProjectFarm It's definitely a lot more than just a regular test video :P

@dj68k 4 жыл бұрын

Second only to the timeless "The banana level is full."

@summertime303 Жыл бұрын

I worked as a pipefitter in a chemical plant for nearly 40 years. Anti seize was a must on every job. We used Never Seize most of the time. Made by Bostic. Great stuff. Your tests are amazing and informative. I love watching them. Please keep it up.

@ProjectFarm Жыл бұрын

Thanks, will do!

@tomrowe9773 Жыл бұрын

Another long time user of Never Seez here, over 45 years of using it.

@robertlevine2152 2 жыл бұрын

I know of two slow-speed diesel engines manufactured in the far east in the mid-70s that experienced some unusual encounters with anti-seize. The engines were both 10-cylinder, 900mm bore turning about 90rpm slow speed diesel engines. The crankshafts were assembled of individual pieces, using shrink or press fits. Someone in the assembly process, without the knowledge of the manufacturer, supervisors, quality control, owner's representatives, or regulatory agencies decided to speed the assembly process by coating the crankshaft parts with anti-seize in way of shrink or press fits. Both engines passed shop tests, dock trials, and sea trials. The ships were put into service with no apparent issues. A least one of the ships experienced engine problems. Examination of the engine found that some of the crankshaft components had shifted and the crankshaft was misaligned. The anti-seize worked as intended, it prevented the components from seizing. The problem was the crankshaft components were not intended to move relative to each other. The moral of the story; is don't put anti-seize in the crankcase and don't lubricate shrink or press fit with anti-seize materials. Bob

@slax59 Жыл бұрын

Great story. William Nixon, Metallurgist, Physicist

@Joseph-C Жыл бұрын

This is why it's so important for every person involved on a large project to understand the whole project and how it functions. That technician/team was clearly told to fit the parts together, but must have had no concept of why they were going together or what exactly was going to happen to the parts once they were in use. They just slapped the parts together because that's the job they were given. That or they just hated their jobs.

@robertlevine2152 Жыл бұрын

@@Joseph-C In this case, as I understood it, the individual loved his job and the company. He was trying to help speed the assembly. He didn't understand the consequences.

@Okurka. Жыл бұрын

How did you manage to misspell "seize" so often?

@robertlevine2152 Жыл бұрын

@Okurka I have no idea. I was never great at spelling. I can also claim it is a result of over-reliance on the spellchecker. I will go back and correct my mistakes.

@darkwinter6028 4 жыл бұрын

“I’ve been applying the rusting agent for the past ninety days” Now THAT’S dedication!

@ProjectFarm 4 жыл бұрын

Thanks for sharing.

@luckymillionaires3167 4 жыл бұрын

Only the best for us viewers lul

@SugarySnackMan 4 жыл бұрын

His dedication is off the charts. I wish other agencies would test as well as he does.

@eddyneill 4 жыл бұрын

I’ve always enjoyed watching your testing processes as you are very thorough keep up the good work

@DEATH_TO_TYRANTS 4 жыл бұрын

I am blown away each and every video.

@MystiqWisdom 4 жыл бұрын

The amount of work this guy puts in is impressive.

@ProjectFarm 4 жыл бұрын

Thanks so much.

@Chance57 3 жыл бұрын

Even putting in work in the comments section with the fans. It's beautiful 😢. Top Tier KZfaq GOAT.

@kick2299 3 жыл бұрын

I know right? Casually mentions having applied there rusting mixture to the bolts every day for 3 months.

@jayhughes3064 Жыл бұрын

I’ve always been a big consumer reports guy , because of their scientific and unbiased testing! Your test are right on par and often superior to them ! Your saving all your subscribers a ton of money and making life much easier by showing us the best products to use ! Please keep up the great work, and we all greatly appreciate the painstaking hours you put in ! Thanks again for all these great test !!

@ProjectFarm Жыл бұрын

Thanks and you are welcome!

@ranger178 Жыл бұрын

consumer reports has gone to crap they are all woke with their tests it is all what is best for environment or saves water or is safest not what works best and is cheapest.

@tommurphy4307 Жыл бұрын

CU is crooked as hell

@jinxtacy 8 ай бұрын

@@ranger178 I'd put them above the autogenerated sites that parse online reviews to create a generic generated review. Consumer Reports probably overall does a decent job and have a genuine business model. I think we should pay for information, but even that can be corrupted by people or companies( ie. Suzuki Motor Corp. v. Consumers Union of the U.S., Inc.). It's kind of like America's Test Kitchen, though I've found sometimes my opinions don't quite align with theirs so I just have to guess where the value lies and if needed return it.

@gregoryfairchild2460 Жыл бұрын

Love these tests! I have used the silver & copper antiseize for years, works great, don't need much. Like my dad used to say, one tube could paint a barn...lol

@ProjectFarm Жыл бұрын

Thanks! Thanks for sharing.

@bobh.4580 Жыл бұрын

One smudge can paint a face. Anti sieze seems seems to get everywhere!

@numberyellow 4 жыл бұрын

Ya' know.... i almost didn't click on this. I thought to myself: "Is anti-seize really THAT interesting?", and then i saw the list of things you were going to do with it.. I'm sorry i ever doubted your ability to make something as mundane as Anti-Seize, so goddamn interesting. I'll never make that mistake again.

@ProjectFarm 4 жыл бұрын

Thanks for watching.

@kamilzmich5961 4 жыл бұрын

you must be new here

@numberyellow 4 жыл бұрын

@@kamilzmich5961 Actually, i've been here pretty much since the beginning. Thanks for playing.

@grandrapids57 4 жыл бұрын

There is no other channel that combines the practical with the absurd like Project Farm.

@AlainVirgin 4 жыл бұрын

How about testing methods of treating wood for outdoor life: Cedar, pressure treated wood, paint, epoxy, linseed oil, boarate treatments, etc?

@Luckingsworth 4 жыл бұрын

That's a great idea. Definitely one we wouldnt see until next year though haha

@EM-fi2qg 4 жыл бұрын

Awesome idea!

@richardpehtown2412 4 жыл бұрын

Creosote, chromated copper arsenate, tar

@FzudemB 4 жыл бұрын

Old engine oil

@Alex632 4 жыл бұрын

That would take like 6 months to complete :0

@sbond1963 Жыл бұрын

I was thinking about making the switch to copper. But thanks to you I’m staying with the Permatex aluminum. Important reason you mentioned is galvanic corrosion. These new vehicles have so much aluminum on them. And the bolts are zinc coated!

@ProjectFarm Жыл бұрын

Thanks for sharing.

@vfb3377 7 ай бұрын

It seems that O2 sensors frequently have copper anti-sieze on them from the factory. Even though I've had no trouble using the aluminum stuff, the copper might be better for that application.

@fabianherrera5427 6 ай бұрын

If you have the money might be good to keep both on hand, i dont so ill stick with forcing the bolts lol

@garbo8962 2 жыл бұрын

Worked in a large slaughter house years ago. They had 2 French presses that worked under extreme pressure to squeeze every drop of tallow out of cooked guts. Had a lot of 1" bolts holding plates on. Before they started to use anti seeze on threads would take a full Saturday & Sunday to remove bolts and perform maintenance. Had to use a 1" old very heavy impact driver to remove bolts. Once anti seeze was used only took a day for entire job. Thanks for another well produced vid.

@alexp.3152 4 жыл бұрын

The extensive testing and the amount of money and time you spend on doing these videos, just to show people how good products are, is just unbelievable and amazing! I strongly belive i say this on behalf of all you other followers as well... THANK YOU SO MUCH!

@ProjectFarm 4 жыл бұрын

You are welcome!

@johnmckenzie1623 4 жыл бұрын

Just want to add my thanks to this comment. Really useful info

@QuippersUnited 4 жыл бұрын

Seeing long term experiments like this always makes me wonder: how many experiments do you have going on right now? Any hints as to what we can look forward to 3 months from now?

@ProjectFarm 4 жыл бұрын

Thank you very much! I always have at least 5 underway at one.

@adamheywood113 4 жыл бұрын

@@ProjectFarm Mate I can't even think of five things to do, let alone all at once.

@braapmoto9268 4 жыл бұрын

kingoftaurus smokes operator video from r6???

@B1gHagar 4 жыл бұрын

@@ProjectFarm One of them is the windshield wiper blade test and I'm looking forward to finding out which blades last the longerst. I live just outside of Houston and it seems like blades don't last for nothing.

@tarstarkusz 4 жыл бұрын

Well, there's the rechargeable batteries and the ongoing test with them.

@vanmann8347 Жыл бұрын

You are my go to guy whenever I want to know which tool, oil,fluids and just about anything else before I make a purchase. There’s nobody else out there like you. You are thorough and honest about everything you test. So many people count on your videos. You are one in a million. Thanks for doing what you do better than anyone else.👍👍👍🇺🇸🇺🇸🇺🇸

@ProjectFarm Жыл бұрын

Thanks so much!

@MicroRotors 6 ай бұрын

As many lawnmower's you have gone through over the years, I wouldn't be surprised the used lawnmower prices have been inflated in your neck of the woods. Great video as usual, Thank You!

@ProjectFarm 6 ай бұрын

lol Thanks!

@williamhu4205 4 жыл бұрын

Literally any viewer here: He's a man of focus, commitment and sheer ducking will.

@ProjectFarm 4 жыл бұрын

Thanks for watching!

@aaronmoritz9878 4 жыл бұрын

I watch this channel, seemingly, religiously. I can’t wait to see what’s next. The layout is great. I love the way he commentates a little and I wanted to add some feedback, which you probably have had before, the charts are perfect. It’s all easy to follow along, even if I have YT playing in the background while I’m doing something. That why I like the commentary.

@ProjectFarm 4 жыл бұрын

Wow, thank you!

@tupacamarushakur64 4 жыл бұрын

Very nicely explained, keep the way of making videos and we will all be very happily enjoying your videoss👍🏼👍🏼

@UnityThroughTruth 4 жыл бұрын

Me too, it's my favorite channel to splurge-watch, like Wranglerstar or Black Conservative Patriot. Awesome tests, often with comprehensive data. A wide variety of subject matter. No sponsorship bias. Never once have I felt talked down to, or like I was stupid. Nor have I been told or shown anything that I wasn't thoroughly explained. My favorite series on YT.

@loweredd 4 жыл бұрын

Make sure to send him a few bucks each month on Patreon guys!

@KJohansson 4 жыл бұрын

Also, PFs Like vs. Dislike ratio is amazing, it averages 10% likes on his views, thats high. Also the dislikes is often under 0.1%, This is legendary.

@MrReed666 Жыл бұрын

You're the real champ here Farm Projects. You are doing a great service to all of us with these outstanding, unbiased, truthful videos. Keep up the great work man 👍 Much love from Alberta.

@ProjectFarm Жыл бұрын

Thanks, will do!

@mBaggins 2 жыл бұрын

Absolutely love your content. You do the testing so that we can make an informed decision without any bias. Love it, thank you.

@ProjectFarm 2 жыл бұрын

Thanks and you are welcome!

@blakeappine 2 жыл бұрын

The fact that you are patient enough to wait 90 days for 1 experiment is amazing. Great dedication! Good content!

@ProjectFarm 2 жыл бұрын

Thanks!

@kviaak7979 2 жыл бұрын

Not being patient enough to wait for 90 days is the result of this smart phone era. And finding that impressive is a statement on its own.

@paultruesdale7680 2 жыл бұрын

😂

@Kittennyanya 2 жыл бұрын

@@kviaak7979 ok.

@ljprep6250 2 жыл бұрын

With all the projects he goes through, I'm surprised he got to it within a year. ;)

@disophisis 4 жыл бұрын

Old lawn mowers everywhere fear this man.

@ProjectFarm 4 жыл бұрын

lol Thanks for watching.

@Thirdbase9 4 жыл бұрын

Not if they want to go out in a blaze of glory!

@Markomyt1 4 жыл бұрын

It's like the little droids on Star Wars... No!!!

@UnityThroughTruth 4 жыл бұрын

I think you're onto something for a good shirt there. @P.F. needs to jump onto that, not just funny, but also true.

@Jetsonn 2 жыл бұрын

Project Farm, you do an excellent job of simulating real life conditions in your videos. I love it.

@ProjectFarm 2 жыл бұрын

Thank you very much!

@collinkasparek6439 Жыл бұрын

By far the best channel on KZfaq! Thank you for unbiased, legit reviews.

@ProjectFarm Жыл бұрын

Thanks and you are welcome!

@ImTheEpicCanadian 4 жыл бұрын

I just want to say that all your testing methods and test rigs are always so well thought out and detailed and I really appreciate it. You are the best! This test took 3 months, thats dedication!

@ProjectFarm 4 жыл бұрын

Thank you very much!

@_REVERIE 4 жыл бұрын

Dude goes hard in the paint, not to mention he's smarter than the average bear!

@muhammadeggy2129 4 жыл бұрын

Lawnmower : Ah, another day without him hurting myself. PF : Allright, lets test this anti seizure as engine oil~ Lawnmower : Ah shit, here we go again.

@endisaragih 4 жыл бұрын

Poor lawnmower..

@jerryvelasco1474 4 жыл бұрын

I believe this is lawnmower abuse.

@mikebolton4257 4 жыл бұрын

Call LPS (lawnmower protective services)

@bertgrau9246 4 жыл бұрын

@@jerryvelasco1474 Remember, if you want an omelet you've got to break some eggs. Meaning a small engine gave its life so we could learn that anti seize is not an oil

@BrewBlaster 4 жыл бұрын

@@robertpicton1 You made me laugh until it hurt.

@matthewharvey4964 2 жыл бұрын

I really enjoy saving money by watching your testing . I feel like the value is worth the time. Your very unbiased and show the good bad and ugly of the products.

@ProjectFarm 2 жыл бұрын

Thanks!

@red1inerr113 4 жыл бұрын

Now if manufacturers could add anti seize when assembling that would be great.

@ProjectFarm 4 жыл бұрын

Thanks for the feedback.

@harryinoklahoma1866 4 жыл бұрын

I've been saying that for years

@greetswithfire1868 4 жыл бұрын

Especially on snow blowers....

@KaMil-gw2qr 4 жыл бұрын

They do, on quality products.

@Beandiptheredneck 4 жыл бұрын

Red1ineRR it really should be factory mandatory.. I live in the rust belt and as far as I’m concerned seized bolts on a 5 years old vehicle should be considered unacceptable

@zin6749 4 жыл бұрын

He looks like he’s about to burst out laughing all the time, and I love it

@ProjectFarm 4 жыл бұрын

Thank you very much! I'm definitely having a lot of fun!

@deviouslick5097 4 жыл бұрын

That is a very accurate observation.

@danlevesque5437 4 жыл бұрын

He reminds me of the pranks we played as kids trying to get the poker face under control just as our pranks get sprung😂

@amycurd4485 4 жыл бұрын

Project Farm qq

@Shabec2982 Жыл бұрын

If you’re into automotive research there isn’t a better channel. I love it here, keep up the great work ✌🏾

@ProjectFarm Жыл бұрын

Thanks! Will do!

@balicrimechannel8143 Жыл бұрын

I spent half a day on the internet trying to get an idea about the best type of anti-seize / corrosion inhibitor to use for restoring my classic cars. After hours of research and still being confused, I watched your video and it gave me the answers I needed straight away. Thanks also for doing the wax and grease; they're things I probably would have tried but now I know their limitations. Thanks so much for taking the time and effort to do such conclusive tests in your videos; they're very educational and invaluable.

@ProjectFarm Жыл бұрын

Thanks and you are welcome!

@risunokairu 4 жыл бұрын

This where lawn mowers who lived wicked lives go when they die.

@spokehedz 4 жыл бұрын

For Science!

@poptartmcjelly7054 4 жыл бұрын

the lawnmower purgatory.

@thibs2837 4 жыл бұрын

@sniuchi2549 4 жыл бұрын

Most honorable death for a lawnmower

@lawpickinglocksmith7689 4 жыл бұрын

Only connecting rods are not properly built

@KDFROST1 4 жыл бұрын

This channel has the best non-bias product reviews. Period!

@ProjectFarm 4 жыл бұрын

Thank you very much! My goal is definitely to deliver unbiased reviews that help everyone. Thanks again!

@andreasguntoro5399 2 жыл бұрын

The only channel that all of the contents I watch never being skipped even a second and I can watch the same video more than once.

@ProjectFarm 2 жыл бұрын

Thanks!

@Richardj410 2 жыл бұрын

I've use the first two products most of my life. Nice to see I haven't been wasting my money. Worked great on my 6' lawn mower the bolts on the blades always came out easily.

@ProjectFarm 2 жыл бұрын

Thanks for the feedback.

@NiftyShifty1 4 жыл бұрын

This guy must be able to rebuild a lawn mower with his eyes closed by this point

@metalman69201 4 жыл бұрын

And he can definitely take one apart and put it back together faster than anybody I know!!

@davidoickle1778 4 жыл бұрын

Nathan Frey No mower is safe from him! LOL

@corpsiecorpsie_the_original 4 жыл бұрын

Every mower abandon near a street with a "Free" sign on it dreams of being picked up by Project Farm.

@MrOner07 4 жыл бұрын

everyone needs to hide their mowers. theres a killer on the loose!

@1979mackdriver 4 жыл бұрын

Corpsie Corpsie It’s like a great warrior death for derilict lawn mowers ,to to go to the project farm is like Valhalla for a Troy Bilt

@MikeHarris1984 4 жыл бұрын

"I suspect this damage was caused before the anti-seize" LMAO... I'd say. That little engine has been through hell!

@ProjectFarm 4 жыл бұрын

Thanks for watching.

@DragonZer0 4 жыл бұрын

@@ProjectFarm Now stupid question. Why did the connecting rod give way in such a fashion?

@yzhang8629 4 жыл бұрын

DragonZer0 prior damage? Maybe anti-seize doesn’t cool the components as well as engine oil, so overheating weakens and damages the components

@Markomyt1 4 жыл бұрын

@@DragonZer0 I think that the anti-seize was too viscous and would not carry away enough heat and once the heat built up in the big end it wore down, softened, and failed. IMHO of course.

@gettintheresafelywithpatf2869 4 жыл бұрын

It might have started before this test, but “anti-seize” lubricants act like marbles in Greece, so it couldn’t get into the journal of the crank/ connecting rod as easily a liquid oil, thus allowing the rod to heat up and expand beyond its capacity and breaking. There was no way that the cylinder would have seized, because the clearance between the piston, rings and cylinder was was more then ample in allowing the lubricant to slip in! Now what did the cam and lifters look like, when doing a test like this on an engine, before and after pics of more then the piston, crank and cylinder head should be taken, a long with any and all measurements possible. Not just use the engine as a Ginny pig! This way your before pics, and measurements will mean one thing, and the after will actually tell the story! I guess your going to send this one up to Musty1 to see if it can be saved , for yet again future failures!

@donhendricks2950 2 жыл бұрын

Always a great place to come and get viable test info to make an informed decision. 👍

@ProjectFarm 2 жыл бұрын

Thanks!

@lenkomsa1399 5 ай бұрын

I find these videos absolutely fascinating! Appreciate your channel

@ProjectFarm 5 ай бұрын

Thanks so much!

@charleetho 4 жыл бұрын

How about testing how much tightening torque and clamping force changes between bare threads, anti-seize and thread locker.

@ProjectFarm 4 жыл бұрын

Great video idea! I can definitely test that.

@kylefowler5082 4 жыл бұрын

yes I agree that's a great idea. I have a bolt torque tables i found online and if I use loctite I torque the bolt to the "lubricated" chart which seems to be around 80% of the "dry" chart

@JETZcorp 4 жыл бұрын

I'd also like to see grease, motor oil, and WD-40 added to that test. A lot of times motor oil on the threads is an unavoidable fact of life, and I'm known to use a bit of WD when reinstalling fasteners with light corrosion.

@somejoe7777 4 жыл бұрын

This is definitely a really good idea. You're not supposed to use anti-size on tire lug nuts/studs, for example, because it changes the proper torque values. Knowing how much the torque value should be modified may allow you to use anti-sieze on the lug nuts/studs should it be required (severe corrosive environment, for example).

@roger7943 3 жыл бұрын

After being an Auto Tech for 44 years, and 34 of those working on a fleet, the Copper anti seize has worked the best in my experience. Great job doing all of your testing!

@ProjectFarm 3 жыл бұрын

Thanks so much!

@wlrottge 3 жыл бұрын

@@ProjectFarm don't use copper anti seize on stainless in salt water, it actually corrodes the stainless; nickel based in marine applications only

@y.blanxo 3 жыл бұрын

Molykote M-77 is the best I've used. Takes longer to dry out than the copper stuff.

@benmac940 3 жыл бұрын

Always found res-q steel to be pretty good personally. Used it on ships for years without issue, would have been interested to see it against these other ones.

@mtn.srlrascu6675 3 жыл бұрын

@@wlrottge nope, tefgel we use

@bikemannc Жыл бұрын

Excellent video you've really confirmed what's best in anti-seize products. A real chuckle buster with the anti-seize in place of engine oil at the end! Keep your music choices going ; enjoying all your choices.

@ProjectFarm Жыл бұрын

Thanks!

@Stover1928 9 ай бұрын

Another great useful video! I look forward to what you are going to test next. Your past video's are just as great . I find myself researching what i need on your channel and finding good results

@ProjectFarm 9 ай бұрын

Thank you!

@Bluuplanet 4 жыл бұрын

Note: AvE emphatically said, "Never-sieze" is NOT a lubricant."

@mcmoolah 4 жыл бұрын

it is abrasive

@SurturLives 4 жыл бұрын

Correction: Never Sneeze

@Ian-ff2hz 4 жыл бұрын

@@SurturLives you beat me

@jamesfair9751 4 жыл бұрын

Dead Channel came to say the same oh well at least it’s been said lol

@mlenz2553 4 жыл бұрын

It's not a good lubricant, but it does lubricate the threads when torquing them down. Taper lock and QD bushings have a warning on them about putting never sieze on them, as it increases the clamping force so much you can split them in half.

@landonweber6123 4 жыл бұрын

This guy is proof you don’t need expensive editing software to be good. Uses movie maker yet makes better content than 90% of other youtubers.

@RustySh4ckleford 4 жыл бұрын

How can you tell?

@ProjectFarm 4 жыл бұрын

Thanks for watching.

@1-Six-dee 4 жыл бұрын

Amen

@ChrisGilliamOffGrid 4 жыл бұрын

@@RustySh4ckleford I use movie maker too, it's basic, but does everything a good producer needs.

@USA-nw7cf 4 жыл бұрын

@@ProjectFarm please do a vid on using transmission fluid as motor oil 🙏

@ashleysmith3906 Жыл бұрын

I really appreciate you making these videos! I feel like I learn so much!

@ProjectFarm Жыл бұрын

Thanks so much! Glad to hear!

@ericb.2519 4 жыл бұрын

I about died when you said 3 months. This guy is honestly one of my favorite content creators. Straight the point. Keep up the good work man!

@ProjectFarm 4 жыл бұрын

Thanks, will do.

@catsspat 4 жыл бұрын

Neighbor sees you grilling and asks, "what's cookin'?" You answer, "oh, just some nuts and bolts." Neighbor leaves you alone... forever.

@ProjectFarm 4 жыл бұрын

lol Thanks for watching.

@paisleyprince5280 4 жыл бұрын

Like when Klinger tried to eat a jeep lol

@benkeysor7576 4 жыл бұрын

Only PF cooks Motor Oil & Hardware.. lol

@ncdave4life 4 жыл бұрын

I was wondering how his next batch of grilled hamburgers tasted.

@catsspat 4 жыл бұрын

@@ncdave4life Not sure about taste, but plenty of iron, no doubt. No need for supplements!

@3betlightftw Жыл бұрын

Youre the man PF. What dedication to do a video over 3months!!

@ProjectFarm Жыл бұрын

Thanks!

@damarpo5467 2 жыл бұрын

As always amazing job! Enjoy all your tests!

@ProjectFarm 2 жыл бұрын

Thanks and you are welcome!

@TheGasMaskGuy96 3 жыл бұрын

I'm always amazed by how much effort you put into your videos

@ProjectFarm 3 жыл бұрын

Thanks so much!

@michaelmartinez1345 2 жыл бұрын

@@ProjectFarm I have to agree with the gasmaskguy95... Great set-up on your videos!!! But please, just a little less carnage using the poor lawnmower engines as sacrificial lambs...😕

@Karabetter 4 жыл бұрын

This guy is crazy-dedicated to his product evaluations and excellent video presentations !!! I only wish I had more thumbs to click up !!!

@ProjectFarm 4 жыл бұрын

Thank you very much!

@WhoTnT 4 жыл бұрын

Here's an extra thumb www.patreon.com/projectfarm 😉

@mikerayis456 6 ай бұрын

You are the King of reviews sir. Thank you.

@ProjectFarm 6 ай бұрын

Thanks!

@danielnewman4876 Жыл бұрын

Terrific video, great dedication, very useful, thanks

@notmeatall7116 4 жыл бұрын

As a marine engineer for the last 30 years I can say that all of these anti-seize products are very limited when used in the marine environment. I stopped using these many years ago and instead use silicone grease (such as caterpillar o-ring lubricant, Dow Corning Formula 111, or NAPA Sil-Glyde). I find that Anti-Seize tends to loose it's oil or grease after awhile leaving only the dry flake. Then sea water seeps in and starts to cause corrosion. Silicone grease stays for years and years. Sea water has no effect on it. Extreme high heat can be a problem though. Exhaust manifold bolts is the only place I use copper based anti-Seize.

@ProjectFarm 4 жыл бұрын

Thanks for sharing.

@peterpiper_203 4 жыл бұрын

So would you recommend it for small engines exposed to the elements

@bobbobbobbob1449 4 жыл бұрын

Years ago i was worki g on miltary vechicals that had been stored 'n the kuwait desert sense desert storm page 1 worki g on M1 abrams and Bradlys mostly, i found the nuuts and bolts cam e off pretty da g easy after 11/12 years ever sense then ive used the cooper based anti seize on all y tower and antennas a d anythi g automotive and marine.

@joshk.6246 4 жыл бұрын

@not meatall I've not been a marine engineer but have had good success with silicone grease on the farm. Ive been using Tribology Tech-Lube silicone paste. It works well. I've found I need to wear gloves because if I get it on my hands they stay slippery for a while as washing doesn't really have much affect taking it off. Maybe Project Farm will do a review of different silicone grease products.

@robertmurdock9750 4 жыл бұрын

I'm a retired marine engineer and I can tell you that anti-seize does work. Dow Corning does work on some things but not 950 degree superheat steam line flange studs but Loctite copper plated anti-seize does. Yard-birds don't like using it because it takes too much time to anti-seize the bolts and studs, and it is almost impossible to get them to apply it to fiber sheet gaskets. I always would have an understanding with the yard that they would apply it to boiler handhole plate threads after I had to burn off 80 handhole plate nuts one time when they used plain nuts instead of 2-H nuts, if they had used anti-seize the nuts would have not have galled.

@xirabolt 4 жыл бұрын

"We're going to test them on threads" Ok, makes sense. "And test bare metal" Works for me, a little extra data. "And if it'll work as engine oil" There's the Project Farm I love.

@ProjectFarm 4 жыл бұрын

Thanks for watching!

@adambauman8044 3 жыл бұрын

I know. He seems to have a fetish with replacing engine oil with things that obviously wont work. I love it. Makes me laugh.

@cbmech2563 3 жыл бұрын

The copper high temp works better wether it's locktite or permatex. My first experience with locktite was on the mold board adjustment bolt (2.5 inch) on a 12 cat grader that had spent 6 months working rip rap on an ocean beach . Absolutely no problem getting it loose .

@jonhunt5408 3 жыл бұрын

Ngl, I was waiting for the fluid film engine oil test.

@FunWithGuns 3 жыл бұрын

Yeah he goes above and beyond everytime 👍🙌

@theblubus Жыл бұрын

Love the double feature in this video here! Reminds me of the older days of seeing if something will run in a motor :)

@ProjectFarm Жыл бұрын

Thanks!

@kevindieterich1254 5 ай бұрын

Great idea and video, always wondered how well my Permatex would work versus bearing grease for antisoeze, now I know ! Thanks !

@ProjectFarm 5 ай бұрын

Thanks!

@RagnarNomad 3 жыл бұрын

I am blown away in amazement by the amount of effort put in by you in these tests!

@ProjectFarm 3 жыл бұрын

Thanks!

@crobinsfly9979 2 жыл бұрын

While you hinted at this in the video: the reason antiseize works so well (in addition to being a lubricant) is because it is hydrophobic and prevents most electrolyte solutions from penetrating the threads and blocking them with corrosion products. Without an observed difference in electric potentials, corrosion simply cannot occur - it's a similar effect to having coated metal with paint, it cannot see the electrolyte to exchange electrons. Anecdotally, in my engineering career, I require the use of antiseize in most fastener applications (just make sure to reduce the torque by about 20% to avoid overloading the fastener...). I believe in the fairly liberal application of it... In fact, a nuclear reactor in the industry I work in experienced an unplanned shutdown (costing the plant easily 2mil+) because several small fasteners had crevice corrosion which allowed a control valve to blow apart. What did all of the failed fasteners have in common? no antiseize. In a sampling of other fasteners at the facility in the same application, those which were installed using antiseize from approximately the same era had no observable corrosion. Antiseize is good stuff!

@ProjectFarm 2 жыл бұрын

Thanks for the feedback.

@BangBang-hk4rg 2 жыл бұрын

Very interesting. Thanks for posting this info 👍

@davidpowell3347 2 жыл бұрын

I usually use antiseize on my lugs but I tighten to the minimum not the maximum,I think if you work in a gas station or on customer's stuff you have to worry about liability since the owner's manuals say not to use antiseize or lubricant, It is amazing at the abuse that lug nuts get from grease monkeys in tire shops armed with air guns and still they may send out a car without tightening the lugs at all or even send out a car with no oil in the crankcase! you can also put antiseize behind the surface where your wheel backside or rotor sits

@isaiahshaffer Жыл бұрын

@@davidpowell3347 I got tires on my truck at a local tire shop, then took it to get inspected and they called me saying I needed several new studs and lug nuts because they had been put on so tight they couldn’t get them off without really messing them up

@Joseph-C Жыл бұрын

@@davidpowell3347 Just saw a truck shop send out a bus that just got new tires on it with several of the bolts hand tight, and several over torqued so hard they twisted them off.. These are bolts big enough to kill someone if they were to be struck by them at highway speed. Not to mention the damage and loss of life that could have been caused if a steering wheel popped off at the wrong time. Yet, nobody will get fired for this and every shop all over the country will keep letting their employees over tighten things with oversize impact wrenches and the like

@superfastjeffoftheworld5817 Жыл бұрын

Thos video for me was mostly entertainment. I really enjoy your channel and refer to it when in question of many DIY project purchases. I love your delivery and content. Thank you! BTW, I bought a 1/4" carbide burr set on Amazon because the comment section mentioned you. Sorry I didn't buy through your channel. You're the best!

@ProjectFarm Жыл бұрын

Thanks and you are welcome!

@williamsporing1500 2 жыл бұрын

This guy is amazing. These are very well thought out experiments.

@ProjectFarm 2 жыл бұрын

Thank you very much!

@williamsporing1500 Жыл бұрын

He’s the best, real world tester

@martymcgill1312 4 жыл бұрын

"It didn't seize, but it sounds like it threw a rod!" LOL

@benkeysor7576 4 жыл бұрын

More like snapped.. LOL

@dotar9586 4 жыл бұрын

To be fair, it says it's anti-seize. It doesn't say it's anti break. lol

@gdh613 Жыл бұрын

I'm amazed and really impressed at the work and preparation you do for these evaluations--the most thorough I've seen. Great use of Scientific method. Thank you.

@ProjectFarm Жыл бұрын

Thanks and you are welcome!

@jordancourtney6537 4 жыл бұрын

Man, I've been here since your channel was way smaller. I think it the first video I saw was the first seafoam video. I cant commend you enough for not selling out. With over 1 million subscribers you could have easily gotten sponsors and your test could have been favorable to those that pay you, but you didn"t and I'm glad you exist to make videos so we can be informed on the products we buy.

@kevinbare1674 3 жыл бұрын

I'm new to the channel, butI love the way he tests these products.

@alanbutler7712 Жыл бұрын

Watching the videos that you make really has me curious as to how you found yourself making videos comparing products? Did you originally go through these kind of evaluations, (in a more limited extent), before buying additional supplies? Thanks for all the great videos!

@Ottonic6 Жыл бұрын

Tough test with so many variables. But it was entertaining. Thanks!

@ProjectFarm Жыл бұрын

Very welcome!

@stanlojewski6761 4 жыл бұрын

Lmao, that was funny. "It did it's job, the engine didn't seize". I use that aluminum anti-sieze religiously, it definitely works well for me here in the rust belt. Great test.

@ProjectFarm 4 жыл бұрын

Thanks for sharing.

@hdog9046 4 жыл бұрын

@burningfeet 57 What are you talking about? The rust belt is a term used for the area where manufacturing has decreased greatly around the turn of the century. The bible belt, what you seem to have confused the rust belt with is just an area where Christianity is followed by more people than average. They are both demographic terms, not religious terms.

@ChrisGilliamOffGrid 4 жыл бұрын

@@hdog9046 Reread his post...🤣😂🤣

@hdog9046 4 жыл бұрын

@@ChrisGilliamOffGrid Well, don't I look stupid now.

@stanlojewski6761 4 жыл бұрын

Hahaha, dang man, some people are just way too bored. Btw,1st amendment, I'll say whatever I want. 🇺🇸 😁

@train1962 4 жыл бұрын

Just when I was getting ready to fill my crankcase with anti-seize.

@andya857 4 жыл бұрын

Now that is funny...

@Darjan_Spasojevic 3 ай бұрын

I know this video is older now, I appreciate your trustworthiness.

@ProjectFarm 3 ай бұрын

Thanks!

@dannygeed9322 2 жыл бұрын

Legend. Best resource on YT! Thanks for your hard work.

@ProjectFarm 2 жыл бұрын

Appreciate that

@omega17168 4 жыл бұрын

thx for the laugh. putting anti-seizer in was a killer idea!

@ProjectFarm 4 жыл бұрын

lol. Thank you! I had a LOT of fun with this video!

@jeremy8715 4 жыл бұрын

10 years living in Maine says yes, the anti-seize does work.

@nghermit4922 4 жыл бұрын

Yup! I bought a VW up here in Maine and someone was nice enough to use anti-seize, it was a pleasure to work on.

@ProjectFarm 4 жыл бұрын

Great point!

@danhard8440 4 жыл бұрын

ya same here in Minnesota but I also spray a can or two of chain lube on everything before every winter

@danhard8440 4 жыл бұрын

you phrased it almost word for word from Mustie1 lol

@virtuosoification 2 жыл бұрын

awesome !!! great video . cannot be thankful enough for what you do . constant knowledge . if only we could all be just as patient seeking answers as you . even a large portion would suffice .

@ProjectFarm 2 жыл бұрын

Thanks!

@nerdnoise 2 жыл бұрын

Wow. That was a lot of work to do that every day for so many days. Thank you.

@ProjectFarm 2 жыл бұрын

You are welcome!

@Hrubeshomes 4 жыл бұрын

Hey I have a very interesting video idea! There are “home defense” bug sprays that claim to prevent bugs from entering the area you spray for up to 12 months! There are many different brands of this product. I think it could make a very interesting and informative video! Thanks project farm

4 жыл бұрын

well i dont think hes an entomologist but its possible he worked pesticides as a profession.

@cdawson198600 4 жыл бұрын

Wyatt Hrubes I’ve always thought .22 rat shot as a good home defense against bugs but maybe that’s just me.

@ProjectFarm 4 жыл бұрын

Great video video idea! Thank you

@Mrcaffinebean 4 жыл бұрын

Wyatt Hrubes “we’ve bought a variety of bugs to test with lol”

@dreamingfool2 4 жыл бұрын

Yes! I live in an area with a lot of insects. I would love to know which residential home defense spray actually works

@simpleman806 4 жыл бұрын

Remember to have a torch nearby. A bolt can't be seized if it's liquid

@ProjectFarm 4 жыл бұрын

Heat is hard to beat! Thank you

@gorjy9610 4 жыл бұрын

My father broke a water tap in garden few days ago, half of old thread stuck in pipe. Extension to be correct, usually he will just go and buy new extension but with lockdown that's not a option. And only reason he ask me for help, usually he's to proud for that. Luckily chinesium taps melt at low temperatures, small blowtorch was enough to melt it away and install new tap.

@TejasToolMan 4 жыл бұрын

Good ole Smoke wrench antiseize

@gorjy9610 4 жыл бұрын

@Dirty Harry problem is that with so many ppl buying only these cheapshit taps it's impossible to buy good one any more in my town. I'll need to travel don't know, 100km to buy good one. One can always order something online but you know how it's going usually, it leak and you need to buy new one fast and then you forget about it for a year and then again it leak and you can't wait for post order and circle is complete, infinity repeat (and Chinese GDP grow :D).

@manstersr Жыл бұрын

Another great comparison video, thanks. I've always been a big fan of Anti-sieze compounds and have been using them for over 45 years as a mechanic. I was introduced to them as a beginner for spark plugs. In the old days spark plugs were prone to seizing in the head and Anti- Seize compounds were the best way to prevent a major job of removing them. I always enjoy your tidbits of info like this one, I didn't think about copper formulations causing a galvanic reaction with aluminum. Good to know. I was told early on that the way they work is with tiny glass beads that stay in the threads to act as bearings when the grease compound dries up. My theory is that the main advantage of using them on spark plugs is that the grease component of the Anti-Seize fills any void in spark plug threads to keep carbon deposits out of them. I'm not sure if that is accurate. I wasn't surprised at the lawn mower test as the main job that engine oil does is to carry heat away from the bearing surfaces and to other parts of the engine block where it can be dissipated through the flow of the oil. I wonder if Anti-Seize would perform better in an engine with an oil pump so it would flow through the bearings. One thing I was really surprised at was the expiration date on the one product. What the heck? It's not food. I have cans of Never-Seize brand from 30 years ago that I still use today.

@ProjectFarm Жыл бұрын

Thanks! Thanks for sharing.

@Tom-ik5sc 4 жыл бұрын

The alternate name for this channel: "Will it work as engine oil?" Lol

@ProjectFarm 4 жыл бұрын

Thanks for sharing.

@maddmaxx636 4 жыл бұрын

Kinda like Will It Blend haha. Will it run in a mower!

@Aperson156 4 жыл бұрын

"Will it lubricate?"

@ricbaker4739 4 жыл бұрын

🤣🤣🤣🤣🤣🤣

@kkrankie 4 жыл бұрын

Next up, Peanut butter or Fluff!

@SgtJoeSmith 4 жыл бұрын

Todd's grass never gets cut. He keeps breaking all his mowers to get out of mowing

@ProjectFarm 4 жыл бұрын

lol Thanks for watching.

@bhess1212 4 жыл бұрын

Probably gone through all of craigslist supply of used mowers in a 60 mile radius!

@tommypetraglia4688 4 жыл бұрын

I think that's the same mower, he owns only one

@mannyvasquez3733 2 жыл бұрын

Great experiment. Very well conducted!

@ProjectFarm 2 жыл бұрын

Thanks and you are welcome!

@axemastersinc3269 3 ай бұрын

Good stuff. Never stopped smiling after the anti-seize oil fill mower run for fun.

@ProjectFarm 3 ай бұрын

Thanks!

@etubrutus3501 4 жыл бұрын

I know this sounds crazy, but when I was in the military I worked on TF 34 jet engines. Our technical manuals would have us apply Phillips milk of magnesia as an anti-seize compound on the nuts and bolts that held the hot section together. I speculate that those areas would get so hot that they were beyond the flashpoint of most anti-seize compounds. But it is a good cheap and non-hazardous alternative to standard anti-seize. Also easily applied, we would put all our nuts and bolts in a Ziploc bag, pour in a little milk of magnesia and shake the bag. I love your show!

@ProjectFarm 4 жыл бұрын

Thanks for sharing.

@ridermak4111 4 жыл бұрын

Damon Traeger When I find tips that crazy-genius, I have to try it. Now if you’re trolling me, my test subject won’t be an expensive victim. Speaking of jet engines, you guys get a grin out of explaining the intricacies of axial compression to curious 12 year old wrenches. (Yeah, that was me 50 years ago). “Well, ya see son, yer family car sucks, squeezes, bangs, and blows....while this here screaming jet sucks, squeezes, and sneezes.” 😎

@T3sl4 4 жыл бұрын

Hmm, makes sense, leaves a granular but crumbly material in the threads, without interacting chemically, and without lubricating the fastener much if any. Magnesia is an incredibly refractory oxide, it will literally outlast anything you can make a bolt out of -- besides tungsten and a couple neighboring metals (none of which you'd want to make a bolt out of, for various reasons).

@Quinid1 4 жыл бұрын

Wish I saw your post before I posted. Yup my squadron used Milk of Magnesia on our T58-GE-8B turboshaft engines as well.

@lloydholt6511 4 жыл бұрын

Damon Traeger I’ve also used this on extreme high temps(2500f). We decanted the liquid off and used the remainder on or studs and nuts. It really does work well in these circumstances

@mr.anonymous6428 4 жыл бұрын

"After 3 months of exposure" ... This guy is amazing! His forethought for these videos is amazing! I have been a faithful watcher for years! I look forward to watching his videos every week.

@ProjectFarm 4 жыл бұрын

Thanks!

@kevinconmy3625 Жыл бұрын

Great video.Always wondered if using this stuff worked.Thankyou!

@ProjectFarm Жыл бұрын

Thanks!

@russtuff Жыл бұрын

lol I was just shopping for anti-seize (because I'm running low of permatex 80078), and I thought "This is something Project Farm really needs to cover". I just love this channel so much!

@ProjectFarm Жыл бұрын

Thanks!

@funkybott0ms 4 жыл бұрын

Could you test garage floor epoxy kits to see which ones resist scratching, oil staining, heat/cold, and wear resistance? Hope this is a good video idea thanks

@ProjectFarm 4 жыл бұрын

Great suggestion! Thank you.

@Ybsjek 4 жыл бұрын

That would be cool

@x_____________5550 4 жыл бұрын

Call Sherwin williams and ask them about tuff coat or the epoxy they have for concrete. Thats what installers use.

@toddrf 3 жыл бұрын

I'll save you all time. None of them. The end.

@stevenmoomey2115 3 жыл бұрын

The problem with the Epoxies, is people don’t prep the floor correctly. Wash and Brush scrub with a strong Powder HE detergent, Tide Recommended. Throughly rinse and rinse again. Squeegee all standing water. Before the floor has a chance to dry, mix 10 parts water to One Part Muriatic Acid, apply with a stiff brush, let set for a half hour, and flush with plenty of water, squeegee standing water. Dry for a week, fan assist if needed, with nothing on the floor, and restrict foot traffic. Rubber boots, protective clothing, safety glasses, Face Shield are a must. A respirator maybe needed, if a enough cross ventilation can’t be provided. I’m not a fan of rubber gloves** when working with acids, prefer a bucket near with cool clear water, for frequent hand, skin washing. If you get acid in the glove**, you may not realize it, till major damage has been done

@local378 4 жыл бұрын

After spending years working in refineries every bolt that I put back in my cars or bikes that does not use Loctite has anti-seize on it. It makes life easier my mechanic. (Me)

@kccodex8931 3 жыл бұрын

What's the best for spark plugs, aluminum head?

@josephgaviota 2 жыл бұрын

I always admire your thoroughness. 👏

@ProjectFarm 2 жыл бұрын

Thanks!

@codyserucsak2501 Жыл бұрын

I got a old can of never seez. Copper and graphite. Always worked well. . I definitely enjoy your test videos. Really putting things to extreme tests.

@ProjectFarm Жыл бұрын

Thanks!

@rickdff62 4 жыл бұрын

In every mechanic's shop or garage, I've been in since I was a child always had a jug of that Permatex anti-seize lying around and it's all I ever used as a result. Super testing my good man.