I love your attention to detail when you do these mods to improve strength etc

Simplement magnifique boulot!

I love how you are managing your INav and BLHeli profiles, their comparison and file . I'm just not sure how to do this myself. nice build. I am building a Nano Goblin at this time . Hopefully with as much detail.

Arctic Silver CPU paste! Love it! I have been wondering why the big ESC was in there, with a Red Bottom and a BEC on your FC for the servos. Great idea with the heatsink, (and the leftover carbon plates for the motor mount), *Brilliant!*

Je me suis inspiré de vos vidéos du Dolphin pour préparer le mien et il vole à merveille. Merci !

nice build!

Damn.... Smooth dolphin 🔥

Love when tools are passed from father to son.

Dang, puttin work!

C'est propre. Je connaissais pas Winmerge. C'est pas mal pour comparer deux dumps.

You got a new sub....mate !! You have some of the amazing content on KZfaq.....These wings are removable or not? Or did you glued them ?

Now thats what i call committing to a battery size.

Nice bird....

Joli ! je decouvre seulement cette aile soit un an apres toi ;) Pourrais tu faire une mise en service de Inav 3.0 .

Nice build！btw how did you do custom osd stuff in iNav？ quite interesting！

Bonjour Olivier! Don't know if you remember but we chatted about the Runcam Split when it was first released a few years ago. I've ordered a Dolphin (from AliExpress, as Banggood price has gone up), looking forward to it arriving. My first fixed wing since about 1995! Just wondering what your thoughts are on inav vs Ardupilot? A few people in the rcgroups thread seem to be scathing of inav but I know you've always used it.

Hi mate! Nice work you've done there! Which kind of pain did you use? I tried a bunch of sprays, aerosols, etc., but it always come off the foam. Thanks!

Hey! Love your videos! Did you glue the nose or leave it just with magnets?

Very nice build! Are you using just standard hot glue?

i am ready for a little chase :D

Salut Olivier. Tu entoures les cables du Rx avec de l alu ? C est pour isoler des interférences ? Tu fais comment stp. Super ta video comme d'hab continue :)

Une fois de plus, tres cool à regarder. Question: Je suis intrigué par ton pistolet à colle chaude ? C'est quel modele de pistolet car j'ai jamais vu de bec tubulaire si long et fin. Merci d'avance !

Does inav really take so long or you are very particular?

hi... how you paint the epp? and whats type of paint do u use?

I have never known any rc airplane person who wants to take space away from their battery compartment?!

Why a high kv motor?

Hello The stock 30A esc is enougt with 4s battery and 5 or 6 inch propeller?

can you share diff all settings?

Wish it had English subtitles:(

Bonjour Olivier, Je ne vois pas de sélection pour le magnétomètre, c'est n'est pas utile avec le BN880 ?

Apologies in advance, but most of the wrok you have done on this build was very sloppy and not thought through step-by-step. Let's start with the camera moounting: There was no need to cut the front section off at all. All you needed to do is to mark the opening that you cut at the end from the top, then fit the camera from the inside with the cable attached, and then glue after you have fed it throught. Also, the PCB of the camera gets very hot. I suggest adding a small heat sink to the main IC on that board or you could fry it, especially considering that you have alsmot no airflow over it for coling. Next, the dipole antenna: This could have been placed elsewhere and I am sure there is an opening for that already. Mounting the lollipop from the bottom to avoid dead spots when flying above your head is a good idea and I have done the same on some of my models, but you will damage the antenna for certain on your first non-grass landing. I have mounted mine internally, but that;s because I have the space in the Ranger 2000 fuselage. In your case, there is a reason why the manufacturer has made the opening on the top and not on the bottom. Next was mounting the flight controller: Why on earth would you have it to the side and not centrered to the aircraft? The IMU needs to be placed as close to the centreline as possible so that your PID controller can work correctly. Also, the FC isn't even rotated 270deg. It was rotated at some angle above/below that, but it was not even orthogonal to the centerline of the aircraft. Regarding, the motor mount: You had so much space BEFORE gluing in that stupid plywood part, why didn't you cut out a circle from carbon fiber (perhaps slightly larger) and then glue that part into the back. There would have been no need to cut open the back and then glue a pirece of carbon fiber that doesen't even match the outline of what you have cut. Finally, the paintwork: Painting should be the last step, not the first. You made so many cuts after the aircraft was painted, it completely ruined your paintjob. Also, why add varnish AND clear tape at the same time. You don't need the varnish at the end, it just adds unncessary weight. The only partially good idea: The battery sides of the battery holder. having the battery not move around is a very good idea, but glueing everything in with hot glue is not a good idea. You could have made the two side parts as separate components and then stick them with double-sided tape. That way you can remove them non-destructively if you need to in the future. Honestly, you could have done a much better and cleaner job at this....

salut a 10:00 c'est quoi ces réglages aux ? svp

Meine ist neuere

I have the same strippers mine finally broke 😂😂

c'est trop reposant cette vidéo