Doubly Fed Induction Motors (Part 2 of 2)

Рет қаралды 1,146

5 ай бұрын

In this lesson we'll learn to repurpose a regular wound rotor induction motor as a doubly fed induction motor. We'll examine regular and flip flopped versions of induction and synchronous mode and introduce hyposynchronous and hypersynchronous operation. We'll learn that a rotating magnetic field on the rotor traveling in the same direction as the stator will allow operation below normal synchronous speed. Conversely we'll learn that a rotating magnetic field on the rotor traveling in the opposite direction as the stator will allow operation above normal synchronous speed. Finally, we'll examine the effect of field current variation in a doubly fed induction motor while in operation. (Part 2 of 2)
___________________
If you wish to support this project please visit the Patreon page at: / bigbadtech
___________________
Copyright information: Use this lecture. Use it at home, at work, or at school. Put it in a playlist, embed it in a website, share it with your coworkers, family, friends, and enemies. I made this lecture and posted it on KZfaq so users everywhere have free access to this information.
This being said, this KZfaq channel is meant to be the sole point of distribution for this lecture. Users are not authorized to download it, change it, or charge for access. Don’t even think of downloading it and uploading to your own channel and pretending it’s your own work. Not cool. Use this lecture and let your friends know this free resource exists.
Use it. Don't steal it. Be cool.
__________________
For more FREE online technical training check out the following playlists available at the bigbadtech channel:
DC Circuit Analysis • DC Circuit Analysis
Single Phase AC Circuit Analysis • Single Phase AC Circui...
3 Phase AC Circuit Analysis • 3 Phase AC Circuit Ana...
Hydraulics • Hydraulics and Electri...
Pneumatics • Pneumatics
Motor Control • Motor Control
Motors and Generators • Motors and Generators
Motor Drives/Variable Frequency Drives (VFD) • Motor Drives
Programmable Logic Controllers (PLCs) • Programmable Logic Con...

Пікірлер: 6

@bentBuilder 5 ай бұрын

So what would happen if you went to the extreme of increasing the variable frequency and voltage on the rotor, where p mech = < 0w. The motor stalls out? VERY GOOD JOB PUTTING THIS VIDEO TOGETHER!

@electrowizard2000 5 ай бұрын

In all the other cases of DFIG operation, you examined a "backwards" architecture (e.g. 3ph on rotor, and shorted stator for induction). Can you discuss a "backwards" DFIG where the AC/AC is supplying the stator? It might be an illuminating comparison; I'm trying to improve my understanding why the power requirements for AC/AC are so low. It's clear why they are lower than a AC/AC converting full generator power, but more wondering why it's not more 'difficult'/power hungry to drive the rotor windings to the requisite frequencies.

@hannespallorarson4285 5 ай бұрын

Could you then have increased speed and decreased speed if you flip the L1,L2, and L2 on the rotor or can you only use it in hypo or hyper mode only?

@BogdanTheGeek 5 ай бұрын

Great lecture. One question: What bonds the upper rotor frequency? As the rotor frequency increases, mechanical power decreases, however the torque remains constant in your examples. Seeing how mechanical power is proportional to torque, and field current is also proportional to torque, Is it safe to assume that once rotor frequency is equal to the stator frequency, the motor is basically in held in position with a torque proportional to the field current?

@bigbadtech 5 ай бұрын

Several folks have asked about this, yes, this is a type of "soft starter in reverse" application. Rather than ramping up stator excitation frequency one instead starts both the stator and rotor at 60Hz so there is no differential (and no physical movement). Then one ramps rotor frequency down so the differential slowly increases and the rotor slowly accelerates.

@BogdanTheGeek 5 ай бұрын

@@bigbadtech But i assume, due to the constant torque, and synchronization, you would get both velocity and position control. I couldn't find any papers describing dual excitation "induction" motors being used as servo motors, but its an interesting topic to explore, if limited in application.