Light-curing modes (continuous, ramp, pulse, high power, extra high power modes)

Light-curing modes (continuous, ramp, pulse, high power, extra high power modes) - Arabic عربي

Рет қаралды 2,041

Күн бұрын

Dental light-curing modes (continuous, ramp, pulse, high power, extra high power modes)
- To learn about dental light-curing units parts & types (QTH and LED generations), watch the video:
• Dental light-curing un...
- To learn about dental light-curing unit chairside radiometers (Types and how to use them), watch the video: • Dental light-curing un...
- To learn about budget dental light-curing units, watch the video: • Light-curing modes (co...
Subscribe for more Preclinical Operative Dentistry videos: / @drafnanoalzain
Music: www.bensound.com
--- Contents of this video ---
00:00 - Introduction
00:14 - Title: Curing modes
00:22 - Curing modes: LCU 1
01:41 - Curing modes: 1. Continuous / Standard / Fast
01:54 - Curing modes: 2. Ramp
02:08 - Curing modes: 3. Pulse
02:13 - Curing modes: LCU 2
02:17 - Curing modes: 1. High
02:20 - Curing modes: 2. Low
02:21 - Curing modes: 3. Ramp
02:25 - Curing modes: 4. Pulse
02:39 - Curing modes: Why?
03:50 - Curing modes: Example 1: 1. Continuous / Standard / Fast
04:16 - Curing modes: Example 1: 2. Ramp
05:03 - Curing modes: Example 1: 3. Pulse
05:39 - Curing modes: Example 2: 1. High
05:45 - Curing modes: Example 2: 2. Low
05:52 - Curing modes: Example 2: 3. Soft (ramp)
06:04 - Curing modes: Example 2: 1. High
06:18 - Curing modes: Example 2: 2. Low
06:34 - Curing modes: Example 2: 3. Soft (ramp)
07:20 - Curing modes: Example 3
07:30 - Curing modes: Example 3: 1. Standard
07:57 - Curing modes: Example 3: 2. High power
08:27 - Curing modes: Example 3: 3. Extra high power
08:46 - Curing modes: Example 3: High power & extra high power (Why?)
Instagram: @afnanalzain
Twitter: @afnanalzain
Email: info@afnanalzain.com

Пікірлер: 13

@amiralamarionnette1391 Жыл бұрын

نزلت من السماء كهدية للطلاب شكرا جزيلا ❤

@drafnanoalzain Жыл бұрын

الحمد لله وفضل منه ❤️ عفوا

@mohammadal-ashqar9589 Жыл бұрын

مجهود يشكر

@zainabdafaei1821 2 жыл бұрын

قناتك تجنننننن ❤️❤️❤️ استمري

@drafnanoalzain 2 жыл бұрын

الله يسعدك 🥰. الحمد لله وفضل منه إنكم بتستفيدوا ❤️❤️❤️

@user-of5ho1vx3t Жыл бұрын

اي كيورينج مود راح يعطي تماثر جيد المود ليس مهم المهم هو الطول الموجي wavelengthو توافقه مع محفزات التماثر photoinitiators في الكمبوزيت شكرا على الفيديوهات المفيدة

@drafnanoalzain Жыл бұрын

صحيح. عفوا

@ilovethepulp Жыл бұрын

Hello! Can you tell me why you would have a pulsing curing mode? thanks!

@drafnanoalzain Жыл бұрын

The rationale of the pulsing and ramp curing modes are similar. The rationale is to: 1. Slow the rate of cure. 2. Extend the viscoelastic phase. 3. Decrease the polymerization shrinkage stresses. 4. Less stress buildup at the bonded interface.

@ilovethepulp Жыл бұрын

@@drafnanoalzain amazing reply thank you! Do you know why you would use pulsing over ramping or is it personal preference?

@drafnanoalzain Жыл бұрын

@@ilovethepulp they are just different methods that were developed. So yes, it is a personal preference. And actually, according to a study they found that there was no significant difference clinically between the soft start curing modes and the continuous mode. So basically it does not make a clinical difference what mode you use. Except the short cure mode (the very short curing time mode such as 3 sec). According to studies the short curing modes generate a lot of stresses within the restoration or at the interface and negatively affects polymerization efficiency and restoration properties. Because there is very short time for the stresses to be released, and can cause entrapment of the unreacted monomers and free radicals within the restoration affecting its properties. So the very short curing modes are opposite to the soft start mode.

@ilovethepulp Жыл бұрын

@@drafnanoalzain amazing response, thank you again!

@drafnanoalzain Жыл бұрын

@@ilovethepulp you are most welcome.