Dreame L10s Ultra water dispensing check

Рет қаралды 18,334

Жыл бұрын

A few tips on how to check whether your L10s is dispensing water while mopping. If you’ve got no water in the base to start with, use the dock self clean (I had to do this about 10 times before water appeared). You can also try the dock self fix option too.
Hopefully Dreame will allow the robot to dispense more water while mopping in the future.

Пікірлер: 83

@tom9380 Жыл бұрын

Detailed showcase of the how the mopping functionality works ! Thanks for this, haven't seen this anywhere else yet.

@TomPattison Жыл бұрын

Glad to be of service 🙂

@zepultra2573 Жыл бұрын

Thank you so much for your video. I just purchased this robot and the mopping function didn’t work. I thought my robot had a default ! I followed your instructions and everything is working wonderfully well. You are a life saver!

@TomPattison Жыл бұрын

Great! Glad I could help. Mine is 5 months old now and is still performing perfectly 👌🏻

@VeroloxLP 3 ай бұрын

Excellent Video! Detailed, Short and straight to the point. You deserve a medal sir.

@lovejesus1393 Жыл бұрын

My manual on page 9 talks about Base Station Buttons. It really tells you to use it to clean the base bottom. You get the base wet and then use brush or washcloth to clean it. Then it will suck out the dirty water. The grate over it comes out to clean.

@MatTeague Жыл бұрын

Thanks for the great video really helped. For me however, base station is filling with water and the injection whole at the back of the robot has water on it, like in your video. It was as you video with the drops two days ago but since, when I take the pads off the plates have no water on them and there are no drops so I’m not sure what’s going on. From what you say it seems the robot is being filled with water but just not releasing it. Everything else though is great about it from my experience

@TomPattison Жыл бұрын

Thanks, glad it helped! If you read the other comments I think Maxairgo had the same issue after a few days too. You may need to use a syringe to pull water from the robot fill nozzle to fully remove any air 🤔

@OMPTraxxs 5 ай бұрын

I have the settings for wetness also on maximum. There is water coming out but not as much as i saw in you video. Could there be anywhere a little chocking and is it possible to clean it ?

@664662 Жыл бұрын

Thanks for this video. I'm about to buy it. One question though: Is the detergent refillable or you need to replace the whole piece everytime is finished?

@TomPattison Жыл бұрын

No problem! You can either buy a new detergent cartridge or fill the old one with another cleaning product. Have a look on Aliexpress and you will see they sell a ‘non official’ refill syringe 👍🏻

@starvictory7079 10 ай бұрын

We have the same issue. Tried straws but nothing. Will try to find a syringe.

@djokal 11 ай бұрын

For me, Auto-add detergent is disabled in the app, and I just replace the detergent bottle. Even if I put the old one back is the same. Any idea how to fix this? And check if the detergent is added.

@SIRTANKTHEBULLDOG-sk1uz Ай бұрын

I have the same mop. But my mop pads keep falling off. Any suggestions. It only happens occasionally like every other day

@alvinng5350 2 ай бұрын

i notice after each mop time, the robot disperse dirty water into the dirty water tank but the amount of water is very very little? is it normal? cleaning around is around 70m2

@3o55 Жыл бұрын

Hello, after how many minutes or square meters does the water come out?

@MaxAirGo Жыл бұрын

After about 6m^2 it starts to release water in bursts of 5 seconds every 25 seconds or so.

@3o55 Жыл бұрын

@@MaxAirGo Thanks

@VeroloxLP 3 ай бұрын

However, one quick question: When doing the deep clean of the base, also the middle dispenser (for the robot) releases some water. First the two bottom left and right dispensers start, but in the last second the middle one as well dispenes some. In your video it does not do this. Is this a defect of my base?

@TomPattison 3 ай бұрын

No mine doesn’t do that. However I’m sure a little bit of water from that nozzle isn’t too bad. Thanks for watching 👌🏻

@Trickster2212 Жыл бұрын

Is this with the mop settings at maximum wetness?

@TomPattison Жыл бұрын

Yes it is 👍🏻

@jpthsd Жыл бұрын

it's been months ,,,how is the water tank on the robot going? Is there any mole?

@TomPattison Жыл бұрын

Hard to tell really as you can’t see the tank. All seems fine though and still working well 👍🏻👍🏻

@jpthsd 8 ай бұрын

it's been months ,,,how's Dreame L10S Ultra servicing your vacuuming/mopping needs? any issue?

@TomPattison 8 ай бұрын

Still good after 8 months - Actually slightly better due to firmware updates 👍🏻

@sarahdara11 6 ай бұрын

I have done the home button at least 9 times and did the straw method. Water comes out when I suck it but still doesnt dispense water.

@TomPattison 6 ай бұрын

Try filling the clean water tank right to the brim first. If that doesn't help, you could also try removing the clean water tank and tipping water down the intake hole while holding the home button down. It should work eventually 🤞🏻

@miki3799 11 ай бұрын

my robot only 1 month, but now the wiper not working, anyone know how to fix? or can connect with Dreame support? :(

@SorryIAteYourCookiesSanta Жыл бұрын

I wonder if drilling the holes slightly will improve water flow🤔

@MaxAirGo Жыл бұрын

I don't think so. It's controlled electronically. It has to be done by firmware update. But then you will simply run out of water to soon with the small 80ml tank. I don't know what max area it runs out of water on max setting. Anyone know?

@TomPattison Жыл бұрын

I’ve done at least 18m2 with full water and it didn’t stop flowing. Also, apparently the water tank is 180ml not 80ml as it says everywhere 🤷🏼‍♂️

@MaxAirGo Жыл бұрын

@@TomPattison That is interesting. If you have a bathroom scale that can measure grams, you can see how much lighter it really gets. Looking at inside pics of L10s onboard tank and comparing it to S7 maxV 200ml tank, doubtful L10s is 180ml.

@xloweric Жыл бұрын

But does it continue dispensing water every time? I just returned a unit because water stopped dispensing after 3-4 minutes every time it ran. I am waiting for the replacement unit to show up. I hope this isn’t a design flaw in all units, but I am becoming less optimistic. Will see what the new one does. Sigh.

@TomPattison Жыл бұрын

Hmm interesting, I’ve got no reason to think it doesn’t continue to dispense water. Perhaps I’ll check later! I think the main problem is that the amount of water dispensed, can’t keep the mops wet enough. Although going back to the base would solve that.

@MaxAirGo Жыл бұрын

Did you get the replacement, how is it? I just ordered L10S and hope no water issues and is better than RR S7+.

@xloweric Жыл бұрын

@@MaxAirGo no I am still waiting. I emailed support yesterday to check and they are supposed to be following up with the warehouse to get a specific date for the shipment. It’s been a week since they received my unit back. I would have returned to Amazon but they only offer a refund so I would have lost my great price.

@MaxAirGo Жыл бұрын

@@xloweric I hope you get it soon and it works as it should.. I am expecting mine tomorrow.

@cykr0 Жыл бұрын

Well same here, it starts with much water and after a few minutes it’s just wet, not slobbery. It refills after every room but not when it’s empty… Chinese logic things I guess